Analog.com Analog Dialogue Wiki 简体中文
EngineerZone
EngineerZone
  • Log In
  • Site
  • Search
  • User
  • Support

    Popular Forums

    • RF and Microwave
    • Power Management
    • Video
    • FPGA Reference Designs
    • Precision ADCs
    • Linux Software Drivers
    • SigmaDSP Processors & SigmaStudio Dev. Tool

    Product Forums

    • A2B
    • Amplifiers
    • Analog Microcontrollers
    • Clock and Timing
    • Data Converters
    • Direct Digital Synthesis (DDS)
    • Energy Monitoring and Metering
    • Interface and Isolation
    • MEMS Inertial Sensors
    • Processors and DSP
    • Switches/Multiplexers
    • Temperature Sensors
    • Voltage References
    View All

    Application Forums

    • Audio
    • Automated Test Equipment (ATE)
    • Condition-Based Monitoring
    • Depth, Perception & Ranging Technologies
    • Embedded Vision Sensing
    • Optical Sensing
    • Precision Technology Signal Chains
    • Video
    • Wireless Sensor Networks Reference Library

    Design Center Forums

    • ACE Evaluation Software
    • ADEF System Platforms
    • Design Tools and Calculators
    • FPGA Reference Designs
    • Linux Software Drivers
    • Microcontroller no-OS Drivers
    • Reference Designs
    • Signal Chain Power (SCP)
    • Software Interface Tools
    • System Demonstration Platform (SDP) Support
  • Learn

    Recent Discussions

    • Pluto + GNURADIO frequency change
    • Pluto SDR
    • pluto sdr pyadi-iio continous iq recording
    • attribute error
    • gps-sdr-sim is not working with my ADALM-PLUTO

    Places

    • ADI Education Home
    • ADI Education China
    • ADI Education India
    • ADI Education Philippines
    • StudentZone (Analog Dialogue)
    • Virtual Classroom

    Latest Webinars

    • Optimizing GaN and GaAs RF Amplifier Performance Using Novel Biasing Techniques
    • Webinar Improving Switch-Mode Power Supplies Using Noise Cancelling Technology
    • Webinar Accelerate Your Design With a 2 to 24 GHz Wideband Transceiver Reference Design
    • How to Design an Optimized Motion Control System for Intelligent Edge Based Surveillance Camera
    • How to Enhance High Precision Current Sensing Systems
    View All
  • Community Hub

    Challenge Yourself!

      KCC's Quizzes: Buffers and Fan Out
    View All

    Places

    • Community Help
    • Logic Lounge

    Resources

    • EZ Code of Conduct
    • Getting Started Guide
    • ADI: Words Matter
    • Community Help Videos
    View All
  • Blogs

     

    How To Design Fieldbus Agnostic Smart Factory Sensors

     

    You Passed EMC Testing… But Wait, Is There More?

    Latest Blogs

    • The 5 Things You Need to Know about RF Matching Networks
    • Does Reliability Prediction Uncertainty Justify Mandating Two Channel Safety?
    • An Inside Look at 2022
    • Meet the Person Behind the Quizzes
    • Updates Required: Why Newer is Better
    Read All Blogs

    ADI Blogs

    • EZ Spotlight
    • The Engineering Mind
  • Partners

    Electronic Design Services - PartnerZone

    • Boston Engineering
    • Calian, Advanced Technologies
    • Colorado Engineering Inc. (DBA CAES AT&E)
    • Clockworks Signal Processing
    • Epiq Solutions
    • Fidus
    • PalmSens
    • Richardson RFPD
    • Tri-Star Design, Inc.
    • VadaTech
    • Vanteon
    • X-Microwave
    View All
ADRadioNet Reference Library
  • Wireless Sensor Networks Reference Library
ADRadioNet Reference Library
Documents FAQ: Unable to connect my EndPoint to the ANodeConfig tool.
  • Members
  • Tags
  • More
  • Cancel
  • Documents
  • ADRadioNet for ADuCRF101
  • ADuCRF101 demodulation principle?
  • ADuCRF101 Shows up as "Unknown Device" in ADRadioNet when i click "Find Devices"
  • advantges and disadvantages between the EV-ADRN-WSN-1Z and EV-ADRN WSN-2Z?
  • Are the devices in the evaluation kit programmed and configured before hand
  • can't find the flash programmer tool in the ADRadioNet package
  • Default configuration settings in the evaluation demo
  • Dose ADI have detailed document for ADradioNet?
  • EVAL-ADF7XXXMB4Z Gerber file
  • EVAL-ADUCRF101 add sensor
  • FCC Certification
  • -Frequently Asked Q's
    • Data Dissemination in Downward Path
    • FAQ: ADRadioNet - Features & Value Proposition
    • FAQ: ADRadioNet - "Upstream" and "Downstream"
    • FAQ: ADRadioNet radio profiles with ADF7024
    • FAQ: Basic Requirements - Boards & Tools for ADRadioNet
    • FAQ: Default configuration settings in the evaluation demo
    • FAQ: Expanding ADRadioNet beyond Evaluation Demo
    • FAQ: How the payload in ADRadioNet protocol is encoded
    • FAQ: How to decipher the messages on the ANodeCenterPoint tool?
    • FAQ: Multi-band, Multi-PHY, Multi-channel?
    • FAQ: on Free Flash Programmer Utility for ADF7xxxMB4z
    • FAQ: Over the Air Commands
    • FAQ: Payload in ADRadioNet protocol
    • FAQ: Unable to connect my EndPoint to the ANodeConfig tool.
    • Procedure to create alternative solution for ANodeCenterPoint tool to receive data from CenterPoint device
  • how can create a graphic in real time with ev adrn wsn 1z ?
  • How can decrease a sleep time, down one second? ADuCRF101MK
  • How can I capture sensor data and use it in my application?
  • how can install ev adrn wsn 1z on windows 10?
  • How can save the data with ev adrn wsn 1z ?
  • How do I expand my network beyond evaluation demo
  • How the payload in ADRadioNet protocol is encoded
  • How to configure the sensor on Bunch WSN?
  • How to Create alternative application to AnodeCP tool?
  • How to decipher the messages on the ANodeCenterPoint tool?
  • How to decode Temperature and humidity value from Bunch sensor board that is seen at AnodeCP GUI?
  • How to recover the setting on EV-ADRN-WSN-1Z
  • How to wake up the EP to capture the active EP data?
  • Identifying sensors enabled and sensors data, from a data packet of End Point in a network
  • Multi-band, Multi-PHY, Multi-channel?
  • my endpoint is not acting immediately on CP commands
  • Node not joining the network after flashing with new firmware
  • port numbers in ADRadioNet?
  • programme microcontroller
  • Prolem with ADuCRF101MK, I don't see the bunch on AnodeCenterPoint
  • Question on data rate selection in router
  • Questions about the ADRadioNet, how to deploy a network?
  • Radio profiles with ADF7024
  • Unable to connect my EndPoint to the ANodeConfig tool.
  • unable to detect BUNCH EP on ANodeConfig tool with ADRadioNet01_EDKv2.0
  • Unable to detect device with ANodeConfig tool
  • Unable to see the node performance of Router
  • What is "Upstream" and "Downstream" in ADRadioNet
  • What's the difference between the WSN development kits EV-ADRN-WSN-1Z and EV-ADRN-WSN-2Z? When and where can they be ordered?
  • Will I loose my configuration settings if the device looses power?
  • WSN Bunch Node PCB Layout File
  • WSN Bunch Node sometimes cannot register

FAQ: Unable to connect my EndPoint to the ANodeConfig tool.

I want to reconfigure my factory configured EndPoint (EP) with new parameters, but I was not able to connect to the ANodeConfig tool. I tried several times in vain. This device is working fine in the network, and I am trying to understand what is preventing the ANodeConfig tool to detect my device.

If your End Point device is functioning perfectly fine, and you are unable to connect to the ANodeConfig tool, it sure could be because of a specific setting in the original configuration.


The setting "[ ] Not Sleepy" in the ANodeConfig tool can be used to set a specific device to disable or enable the sleep mode functionality. In your particular case, it is possible that you left the setting open, which means your device is a SLEEPY device as in a deployment scenario.

 

There are two ways to resolve this issue:

1. Network Mode: This works only if the EP is registered in a network. Using the ANodeCenterPoint tool, you can post a "Disable Low Power Mode" message from [Config/commands] window.

 

2. Normal Mode: Go and flash the device again. Open ANodeConfig tool, and configure all the settings. Before saving the configuration, ensure to check the "[v] Not Sleepy" box. Then write the configuration in to the device. You should be all set from now on.


Note: Please make sure to uncheck this box to operate the device in sleep mode. Usually you would need this in a deployment scenario.


This FAQ was generated from the following discussion: Unable to connect my EndPoint to the ANodeConfig tool.

  • Frequently Asked Q's
  • Share
  • History
  • More
  • Cancel
Related
Recommended
 
Social
Quick Links
  • About ADI
  • Partners
  • Analog Dialogue
  • Careers
  • Contact us
  • Investor Relations
  • News Room
  • Quality & Reliability
  • Sales & Distribution
  • Analog Garage
Languages
  • English
  • 简体中文
  • 日本語
  • Руccкий
Newsletters

Interested in the latest news and articles about ADI products, design tools, training and events? Choose from one of our 12 newsletters that match your product area of interest, delivered monthly or quarterly to your inbox.

Sign Up
Switch to mobile view
Analog Logo
© 1995 - 2023 Analog Devices, Inc. All Rights Reserved 沪ICP备09046653号-1
  • ©
  • 1995 - 2023 Analog Devices, Inc. All Rights Reserved
  • 沪ICP备09046653号-1
  • Sitemap
  • Privacy & Security
  • Privacy Settings
  • Terms of use
EngineerZone Uses cookies to ensure you get the best experience in our community. For more information on cookies, please read our Privacy & Security Statement.