groupUrl: https://ez.analog.com/wireless-sensor-networks-reference-library/adradionet/
Analog.com Analog Dialogue Wiki English
Analog.com Analog Dialogue Wiki 简体中文
EngineerZone
EngineerZone
  • Site
  • User
  • Site
  • Search
  • User
EngineerZone
EngineerZone
  • Log in
  • Site
  • Search
  • Log in
  • Home
  • Blogs ⌵
  • Browse ⌵
    • All Groups
    • All Members
  • Support ⌵
    • 3D ToF Depth Sensing
    • A2B
    • Aerospace and Defense (ADEF)
    • Amplifiers
    • Analog Microcontrollers
    • Analysis Control Evaluation (ACE) Software
    • Audio
    • Clock and Timing
    • Condition-Based Monitoring
    • Data Converters
    • Design Tools and Calculators
    • Direct Digital Synthesis (DDS)
    • Embedded Vision Sensing
    • Energy Monitoring and Metering
    • FPGA Reference Designs
    • Industrial Ethernet
    • Interface and Isolation
    • Low Power RF Transceivers
    • MEMS Inertial Sensors
    • Motor Control Hardware Platforms
    • Optical Sensing
    • Power Management
    • Precision Technology Signal Chains
    • Processors and DSP
    • Reference Circuits
    • RF and Microwave
    • Signal Chain Power (SCP)
    • Switches/Multiplexers
    • Temperature Sensors
    • Video
    • Wide Band RF Transceivers
    • Wireless Sensor Networks Reference Library
  • About EZ
  • More
  • Cancel
  • 主页
  • 浏览 ⌵
    • 收件箱
    • 个人设置
    • 会员
    • 专区列表
  • 论坛专区 ⌵
    • 放大器专区
    • 精密转换器专区
    • 音频专区
    • ADE电能计量专区
    • MEMS和传感器专区
    • 接口和隔离专区
    • Power 中文专区
    • ADUC微处理器专区
    • 锁相环专区
    • 开关和多路复用器专区
    • 温度传感器
    • 基准电压源专区
    • 资源库
    • 论坛使用指南
    • 技术支持参考库
    • 在线研讨会
    • 论坛社群活动
    • 论坛激励活动
  • More
  • Cancel
ADRadioNet Reference Library
  • Wireless Sensor Networks Reference Library
ADRadioNet Reference Library
Documents WSN Bunch Node sometimes cannot register
    • New
    ADRadioNet Reference Library requires membership for participation - click to join
    • Documents
    • ADRadioNet for ADuCRF101
    • ADuCRF101 demodulation principle?
    • ADuCRF101 Shows up as "Unknown Device" in ADRadioNet when i click "Find Devices"
    • advantges and disadvantages between the EV-ADRN-WSN-1Z and EV-ADRN WSN-2Z?
    • Are the devices in the evaluation kit programmed and configured before hand
    • can't find the flash programmer tool in the ADRadioNet package
    • Default configuration settings in the evaluation demo
    • Dose ADI have detailed document for ADradioNet?
    • EVAL-ADF7XXXMB4Z Gerber file
    • EVAL-ADUCRF101 add sensor
    • FCC Certification
    • +Frequently Asked Q's
    • how can create a graphic in real time with ev adrn wsn 1z ?
    • How can decrease a sleep time, down one second? ADuCRF101MK
    • How can I capture sensor data and use it in my application?
    • how can install ev adrn wsn 1z on windows 10?
    • How can save the data with ev adrn wsn 1z ?
    • How do I expand my network beyond evaluation demo
    • How the payload in ADRadioNet protocol is encoded
    • How to configure the sensor on Bunch WSN?
    • How to Create alternative application to AnodeCP tool?
    • How to decipher the messages on the ANodeCenterPoint tool?
    • How to decode Temperature and humidity value from Bunch sensor board that is seen at AnodeCP GUI?
    • How to recover the setting on EV-ADRN-WSN-1Z
    • How to wake up the EP to capture the active EP data?
    • Identifying sensors enabled and sensors data, from a data packet of End Point in a network
    • Multi-band, Multi-PHY, Multi-channel?
    • my endpoint is not acting immediately on CP commands
    • Node not joining the network after flashing with new firmware
    • port numbers in ADRadioNet?
    • programme microcontroller
    • Prolem with ADuCRF101MK, I don't see the bunch on AnodeCenterPoint
    • Question on data rate selection in router
    • Questions about the ADRadioNet, how to deploy a network?
    • Radio profiles with ADF7024
    • Unable to connect my EndPoint to the ANodeConfig tool.
    • unable to detect BUNCH EP on ANodeConfig tool with ADRadioNet01_EDKv2.0
    • Unable to detect device with ANodeConfig tool
    • Unable to see the node performance of Router
    • What is "Upstream" and "Downstream" in ADRadioNet
    • What's the difference between the WSN development kits EV-ADRN-WSN-1Z and EV-ADRN-WSN-2Z? When and where can they be ordered?
    • Will I loose my configuration settings if the device looses power?
    • WSN Bunch Node PCB Layout File
    • WSN Bunch Node sometimes cannot register

    WSN Bunch Node sometimes cannot register

    Original Question: WSN Bunch Node sometimes cannot register by tristantech

    I am using a WSN Bunch node and center point, both loaded with the latest firmware. When watching the packet window in the center point application, nodes occasionally will send one or two registration packets upon powering up, but then stop transmitting without ever sending any data. Other times they will register properly and begin reporting sensor readings. I was wondering if anybody else has experienced this problem and if there are any known workarounds.


    Verified Answer: RE: WSN Bunch Node sometimes cannot register by harishkumarkatam

    hi

    I have tried using the same combination of the hardware with different battery powered Bunch boards as EndPoints. I was not able to reproduce the issue of communication failure, with the prebuilt binaries provided with the ADRadioNet EDKv2.0 release. Can you try mass erasing the Bunch board using CM3WSD and flash again with the prebuilt binaries provided with the ADRadioNet EDKv2.0 package and check the communication.

    If the issue still exists, to eliminate the doubt on hardware please use the different set of hardware boards and test.

    thanks

    Harish


    Question: RE: WSN Bunch Node sometimes cannot register by harishkumarkatam

    I presume the ADRadioNet EDKv2.0 version of binaries are used for the demo setup.  How often the issue is noticed? Can you share the screen shots of Start and Network overview windows of the ANodeCenterPoint tool when the issue is observed.

    thanks

    Harish


    Question: RE: WSN Bunch Node sometimes cannot register by tristantech

    Hi Harish,

    I looked at those tabs, and they are both blank.


    Question: RE: WSN Bunch Node sometimes cannot register by harishkumarkatam

    Hi Tristan,

     

    If you don’t see any messages or data on Start and Network overview it means the EP is not getting registered to the network. Please provide me the following information.

    • Version of the binaries used on both the EP and CP
    • Mode of powering the EP (battery or USB-SWD/UART-EMUZ)
    • Revision of boards used.
    • How often you see the issue? Every time you power reset the EP you face this issue?

    Please try to power rest the EP board properly and check. Every time you flash or change the configuration of the board power reset is must.


    Question: RE: WSN Bunch Node sometimes cannot register by tristantech

    The binaries used on the EP and CP are the latest available for download from the ADI website. They are the second version of the protocol. The HEX files are dated April 8 2015. (These binaries are different from the ones included on the flash drive that shipped with the kit) The boards started out as the earlier version, which I upgraded using CM3WSD to the current version. The EPs are powered via coin cell, but when I tried to substitute the battery for a 3V bench supply, the issue did not go away. The center point is CP1Z/Rev E and the nodes are EV-BUNCH-WSN-1Z/Rev B. Perhaps the old hardware is not compatible? The issue happens very frequently. Sometimes packets never come, sometimes it stops after a few discovery packets, and occasionally data comes normally. I power cycle the boards between configurations.

    Thanks for all your help so far,

    Tristan


    Question: RE: WSN Bunch Node sometimes cannot register by tristantech

    Hi Harish,

    Performing the mass reset did the trick; the hardware is now running the V2.0 protocol reliably. There must have been some configuration settings from the old firmware stilled stored somewhere in the modules that was causing problems.

    Thanks so much for your help!

    Tristan

    • Share
    • History
    • More
    • Cancel
    Comments
    Anonymous
    Related
     
    社交网络
    快速链接
    • 关于ADI
    • Partners
    • 模拟对话
    • 职业
    • 联系我们
    • 投资信息
    • 新闻中心
    • 质量和可靠性
    • 办事处与代理商
    • Analog Garage
    语言
    • English
    • 简体中文
    • 日本語
    • Руccкий
    电子快讯

    欲获得最新ADI产品、设计工具、培训与活动的相关新闻与文章,请从我们的在线快讯中选出您感兴趣的产品类别,每月或每季度都会发送至您的收件箱。

    订阅
    Switch to mobile view
    Analog Logo
    © 1995 - 2022 Analog Devices, Inc. All Rights Reserved 沪ICP备09046653号-1
    • ©
    • 1995 - 2022 Analog Devices, Inc. All Rights Reserved
    • 沪ICP备09046653号-1
    • 网站地图
    • 隐私和保密政策
    • 隐私设置
    • 使用条款
     
    Social
    Quick Links
    • About ADI
    • Partners
    • Analog Dialogue
    • Careers
    • Contact us
    • Investor Relations
    • News Room
    • Quality & Reliability
    • Sales & Distribution
    • Analog Garage
    Languages
    • English
    • 简体中文
    • 日本語
    • Руccкий
    Newsletters

    Interested in the latest news and articles about ADI products, design tools, training and events? Choose from one of our 12 newsletters that match your product area of interest, delivered monthly or quarterly to your inbox.

    Sign Up
    Switch to mobile view
    Analog Logo
    © 1995 - 2022 Analog Devices, Inc. All Rights Reserved 沪ICP备09046653号-1
    • ©
    • 1995 - 2022 Analog Devices, Inc. All Rights Reserved
    • 沪ICP备09046653号-1
    • Sitemap
    • Privacy & Security
    • Privacy Settings
    • Terms of use
    EngineerZone Uses cookies to ensure you get the best experience in our community. For more information on cookies, please read our Privacy & Security Statement.