Discussion - Recent Threads

Can MDuCM3029 + ADF7030-1 be used for AD6LoWPAN ?

Hichem_Ncir — Thu, 20 Jul 2017 12:33:34 GMT

hello everyone,

i have an ADuCM3029 EZ-KIT 1.2 with ADF7030-1 transceiver. Let me know if i can use AD6LoWPAN over it, and what am i suppose to change or add to the code?

Can I send data from Node to Border Router in AD6LoWPAN?

akla — Tue, 01 Nov 2016 14:33:34 GMT

Is it possible, that Node initiates communication with Border Router?
For example, sensor, attached to Node measures something critical and Node application software sends alarm trap to Border Router .

GPIO and Transceiver Interrupts

Maria — Fri, 28 Oct 2016 17:30:38 GMT

How to disable GPIO or Transceiver Interrupts? in AD6LoWPAN01 EDKv1.0 Platform: EV-ADRN-WSN-1Z.

I tried calling the API Disable_Transceiver_Interrupts( ), it got re-enabled after 10 sec by itself, is their any default time set for disabling the interrupts.

ADUCRF101 Software and Application framework; Mesh Network in Sub-GHz

ijaz — Thu, 20 Oct 2016 14:11:04 GMT

Hi,

We were looking for Sub-1-GHz Low Cost Low Power Mesh Network Solution, MCU + RF transceiver integrated. ADUCRF101 is under consideration for the same.
I could find that, 6LoWPAN is the only open standard that supports ‘mesh’ in Sub-GHz RF band.

Could you please clarify the following points to proceed with module selection:

Does ADUCRF101 has a supported 6LoWPAN software stack?

As we don’t require IP driven nodes and due to lack of IPv6 support, is it possible to create a mesh network with the software package for monitoring application with out internet connectivity. That is only local data exchange between devices inside the 6LoWPAN

I would be grateful for any comments or suggestions. Thank you

Ijaz Fazily

Received packets size

Ramya — Tue, 04 Oct 2016 14:43:46 GMT

With reference to the posts Data Packets from Node WSN and Restrict End Node from pushing packets continuously. The size of Packets received is 80 bytes, Is their any possibilities to reduce this packets size , say only to the Mac ID and the Accelerometer Measured values.

Data Packets from Node WSN

Ramya — Sat, 17 Sep 2016 09:44:00 GMT

how to stop receiving packets for 30 sec once the 1st packet is received from the node WSN , even though their s activities detected in sensors

ADXL362 sleep time and activity

Ramya — Sat, 17 Sep 2016 09:27:34 GMT

in Bunch WSN , once the activity is detected in ADXl362 it should go to sleep for 30 sec , in should not detect any activity for 30 sec, what should be done to achieve this

ADF7242 with RaspberryPi

mchetan133 — Wed, 07 Sep 2016 20:53:14 GMT

Is radio module ADF7242 (Low Power IEEE 802.15.4) compatible with RaspberryPi3?

How to set sleep mode in ADXL362(MEMS)?

Praveeng — Wed, 03 Aug 2016 09:01:05 GMT

Hi, I am working on AD6LoWPAN01 EDKv1.0 Platform: EV-ADRN-WSN-1Z. Its an Evaluation kit. I am not able to set sleep mode of ADXL362, So can any one suggest me , How to set sleep mode?

ADXL362

Praveeng — Mon, 18 Jul 2016 10:34:03 GMT

Hi..

I am not able to set threshold value in ADXL362, please suggest me how to set the threshold value in this .

Thanks

HOW CAN I GET THE TINY WSN SCHEMATICS

chithra — Tue, 12 Jul 2016 11:05:47 GMT

Hi,

Is it possible to obtain full documentation for Tiny WSN. Specifically schematics and layout design. Please find the required documentation file to be attached

ADWSN-UI tool displaying "unknown device" on my centerpoint node

yoshimasa — Mon, 06 Jul 2015 19:31:35 GMT

Hi,

I have a similar issue with another discussion regarding the ADWSN-UI tool.
My centerpoint node (AduCRF101) is displayed as "unknown device" whilst my BUNCH WSN boards are recognized properly as "endpoint"

Does any of you know how to make the solution recognize the centerpoint?

Thanks

I have WSN Bunch version kit, Can this be used for AD6LoWPAN also?

NagarjunaG — Fri, 26 Jun 2015 07:07:37 GMT

I purchased Wireless Sensor Network Development Kit – Bunch Version (EV-ADRN-WSN-1Z) from www.analog.com/wsn about a month back to evaluate the other technology. Will I be able to use the same kit to evaluate this AD6LoWPAN solution, Let me know.

Does the new kit come with AD6LoWPAN devices pre-programed and pre-configured? Explain the demo binaries.

Packet format for 6LoWPAN/AD6LoWPAN?

NagarjunaG — Fri, 26 Jun 2015 05:30:23 GMT

What is the standard packet format for AD6LoWPAN?

How different is AD6LoWPAN from Contiki OS based implementation?

NagarjunaG — Fri, 26 Jun 2015 05:12:26 GMT

How different is AD6LoWPAN from Contiki OS based implementation? List the main differences if any?

IP address allocation for my 6LoWPAN devices in the network?

NagarjunaG — Fri, 26 Jun 2015 04:07:28 GMT

How is the IP address assigned to each of WSN/6LoWPAN devices in the network?

Device types in AD6LoWPAN EDK?

NagarjunaG — Fri, 26 Jun 2015 03:58:55 GMT

What are the different types of devices supported in AD6LoWPAN EDK? Can you explain the functionality very briefly?

How to interpret the sensor data collected on ADWSN tool?

NagarjunaG — Fri, 26 Jun 2015 02:04:29 GMT

I know the data from different sensors gets collected by the Border Router, and is displayed on the PC monitor using the ADWSN-UI tool. I want to know how the raw data can be interpreted?

How to send “User Defined Commands” from Border Router to Node?

NagarjunaG — Fri, 26 Jun 2015 01:24:20 GMT

Can I make my own “User Defined Commands” to send from Border Router to the Node.

I prefer to do this without any code modifications. Is this possible?

My WSN nodes are not communicating

NagarjunaG — Thu, 25 Jun 2015 09:00:45 GMT

My WSN nodes are not communicating. How do I know if these devices joined a network?

Can I send commands from Border Router to Node in AD6LoWPAN?

NagarjunaG — Thu, 25 Jun 2015 08:35:28 GMT

Can I send commands from Border Router to Node in AD6LoWPAN? What type of commands are supported inthe evaluation package?

question on multi-channel, and channel hopping

NagarjunaG — Thu, 25 Jun 2015 08:32:38 GMT

In a single 6LoWPAN WSN network, can the devices operate in different channels?

Is there any channel hopping concept in AD6LoWPAN?

What is the default tx power in AD6LoWPAN EDKv1.0, and how do I change it?

NagarjunaG — Thu, 25 Jun 2015 08:20:26 GMT

What is the default transmit power used in AD6LoWPAN EDKv1.0?

How do I change it to experiment more with my network?

How to interpret the different messages received on the UI tool?

NagarjunaG — Thu, 25 Jun 2015 08:00:18 GMT

How to interpret the different messages received at the ADWSN UI tool in the “Monitor And Control” window start tab?

how many number of sensors can be displayed in the monitor?

NagarjunaG — Thu, 25 Jun 2015 07:57:45 GMT

Data corresponding to how many number of sensors is displayed in the ADWSN UI tool?

What if I want interface more sensors in my design, how would I be able to visualize this data from new/additional sensors?