Hi, We are trying to configure the DPD in AD9375 with the default configuration that is given in the myk_init.c. There is no any detailed coding sequence so, We are following the below mentioned sequence. Radio Off Abort Init cals Enabling DPD in the TXProfile Structure Configuring DPD run init cals with DPD_INIT wait init cals getting the Enabled Tracking calMasks enabling the Tracking cals by adding TRACK_TX1_DPD with the existing tracking calMasks Radio ON Changing the ORX Path to OBS_INTERNALCALS With the above mentioned sequence waitInitCals is getting failed with an error "myKonos_WaitInitCals() returned an ARM Error", errorcode = 0 and errorFlag = 0; we don't know whether any additional calibration or other dependencies is required for the DPD Configurations. If anything wrong with the above sequence, Kindly share a working sequence to configure DPD. Thanks in advance Deva.

Products In This Thread

AD9375 Recommended for New Designs
The AD9375 is a highly integrated, wideband radio frequency (RF) transceiver offering dual-channel transmitters (Tx) and receivers (Rx), integrated synthesizers...
Datasheet
AD9375 on Analog.com

How to configure DPD in AD9375

Devaguru

on Aug 19, 2022

Category: Software

Product Number: AD9375

Hi,

We are trying to configure the DPD in AD9375 with the default configuration that is given in the myk_init.c.

There is no any detailed coding sequence so, We are following the below mentioned sequence.

Radio Off
Abort Init cals
Enabling DPD in the TXProfile Structure
Configuring DPD
run init cals with DPD_INIT
wait init cals
getting the Enabled Tracking calMasks
enabling the Tracking cals by adding TRACK_TX1_DPD with the existing tracking calMasks
Radio ON
Changing the ORX Path to OBS_INTERNALCALS

With the above mentioned sequence waitInitCals is getting failed with an error "myKonos_WaitInitCals() returned an ARM Error", errorcode = 0 and errorFlag = 0;

we don't know whether any additional calibration or other dependencies is required for the DPD Configurations.

If anything wrong with the above sequence, Kindly share a working sequence to configure DPD.

Thanks in advance

Deva.

0 srimoyi

on Aug 22, 2022 3:18 PM
Refer to the below link for running DPD on Python:

File Uploads

Refer to the below link for reference:

ADRV-DPD1/PCBZ Board DPD Python Script

https://ez.analog.com/wide-band-rf-transceivers/tes-gui-and-api-software-ad9371-ad9375/f/q-a/164489/how-to-config-dpd-on-ad9375/371893#371893
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
0 Deva1998
on Sep 13, 2022 7:40 PM in reply to srimoyi
Hi,

I am using C for my application and I referred the above given link (2nd).

I need to configure the DPD in run time like we are doing in the AD9375 DPD GUI, but the code is used to configure the DPD while initializing the chip.

I am following the below mentioned sequence:

RadioOff

Configuring DPD

abortInitCals

RunInitCals with DPD_INIT

WaitInitCals

GetEnabledTrakingCals

EnableTrakingCals with TRACK_ORX1_QEC and TRACK_TX1_DPD

Radio On

ObsPathSelection as OBS_INTERNALCALS

whenever I am trying to configure the chip with this sequence, it is getting failed at "waitInitCals()" and returned with an Error "282" stating "Unknown error was encountered", errorFlag as 7 and ErrorCode as 15.

But there is no error code 15 in the UG998. Please provide the significance of this error code.

Also, I tried DPD with Analog devices DPD GUI using Evaluation board. in the GUI on clicking the DPD Adaptation radio button under PA calibration tab, DPD was successfully observed.

Can you please share the Function calls and sequence in which they are being initiated on clicking the DPD Adaptation radio button?

Thanks

Deva.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
0 srimoyi

on Sep 15, 2022 4:49 PM in reply to Deva1998
Can you try running only DPD init cals?

Try following the below steps:

Enable TX data

Configuring DPD, run DPD init cals

WaitInitCals

GetEnabledTrakingCals

EnableTrakingCals with TRACK_TX1_DPD
Cancel
Up 0 Down

Reply

Verify Answer

Cancel