• State Verified Answer
  • Replies 4 replies
  • Subscribers 1 subscriber
  • Views 1544 views
  • Users 0 members are here
Similar Content 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
ADN2820 Question



		

			

									
					    Carlos976
					
							

			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Feb 14, 2017 
				
			
			
		
    

				
		
    
		    		    
		    
		    	
			
    Dear Sir/Madame
    
 
          I would like to use your TIA ADN2820 with an photo-diode. The functional block diagram proposed in Figure 1. of datasheet has the anode of photo-detector connected with input pin (IN). However, I have only access to cathode of our photo-detector and the anode is directly connected to ground. Can be this request satisfied using your TIA ADN2820, having the photo-diode correctly biased and respecting all the chip specifications? If not, may Analog propose other TIA?
    
 
    Yours sincerely, Carlos Ferreira  
    
									
			        
		
    

				
						
        

    
    Tags: 
                                            
                 amplifiers
                
                                                    
                 Digital Beamforming Techniques for Phased Array Applications
                
                                                    
                 optical transimpedance amplifiers
                
                                                    
                 Specialty Amplifiers
                
                                                    
                 adn2820 question
                
                                        
                                            
                
                
                                        
                                            
                
                
                                
                    Show More
            
    
    
    

		
    
			
						
									
									
						
						
			
			
			
			
		
    

        
        

					
    
			
    


    
















    
	
    
	
    
					



			








	
	
	
	



Parents
	
      
	

    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
        
            
						
                            
            
            				
            
                on Feb 14, 2017 5:05 PM
            
            
					
        
	
        

		
		
        
					
        Thank you for your fast response
        
 
        The interest bandwidth of the photo-detector signal should be between 1.4 GHz and 2.6 GHz (the data will have about 2 Gbits/s). Our photo-detector was designed using photonic integrated techniques and only has two pads: one ground and the cathode (their impedance is capacitive) . The TIA and photo-diode will be bond to "top layer" pads/tracks using one of the ROGERS substrates. We thought in connected the TIA outputs to SMA RF connectors, the grounds to PCB bottom layer using vias and the DC voltages to Right Angle SMT 2 male connectors.
        
 
        Maybe, we will need a reverse bias voltage of +2.0V. Could be a bias-T circuit a possible solution to this problem?
        
 
        Best regards,
        
 
        Carlos Ribeiro
        
			
        

		
			
	      

		
		
	
        
	
        
		
        
			
		
        
	
        
	
        
		
						
						
				
						
				
				
		
		
        
			
		
        
	
        

        

        • 

	
      



Reply

        


      • 
	
        



	
		
	
	



        
	
        
		
        
							
					
        
		
        
			
													0
							
			
				
									
							        
			
			
			
          
            
						
                            
            
            				
            
                on Feb 14, 2017 5:05 PM
            
            
					
          
	
          

		
		
          
					
          Thank you for your fast response
          
 
          The interest bandwidth of the photo-detector signal should be between 1.4 GHz and 2.6 GHz (the data will have about 2 Gbits/s). Our photo-detector was designed using photonic integrated techniques and only has two pads: one ground and the cathode (their impedance is capacitive) . The TIA and photo-diode will be bond to "top layer" pads/tracks using one of the ROGERS substrates. We thought in connected the TIA outputs to SMA RF connectors, the grounds to PCB bottom layer using vias and the DC voltages to Right Angle SMT 2 male connectors.
          
 
          Maybe, we will need a reverse bias voltage of +2.0V. Could be a bias-T circuit a possible solution to this problem?
          
 
          Best regards,
          
 
          Carlos Ribeiro
          
			
          

		
			
	      

		
		
	
          
	
          
		
          
			
		
          
	
          
	
          
		
						
						
				
						
				
				
		
		
          
			
		
          
	
          

          

          • 


        


Children
	
        No Data