Color-bar test pattern broken from ADV7280-M

Question

I have design custom board for raspberry pi board to support analog camera image. 
 as result i have get broken color-bar test pattern. 
 Is there any check point to resolve this issue? 
 
 Thanks for reply 
 
 (1) color-bar test pattern output

(2) used i2c script 
 * I used "Color Bars 480i MIPI Out" from ADV7280M_Cust-VER.4.1.txt 
 42 0F 00 ; Exit Power Down Mode 42 0E 00 ; Enter User Sub Map 42 0C 37 ; Force Free-run mode 42 02 54 ; Force standard to NTSC-M 42 14 11 ; Set Free-run pattern to color bars 42 03 4E ; ADI Required Write 42 04 57 ; Power-up INTRQ pin 42 13 00 ; Enable INTRQ output driver 42 17 41 ; select SH1 42 1D C0 ; Tri-State LLC output driver 42 52 CD ; ADI Required Write 42 80 51 ; ADI Required Write 42 81 51 ; ADI Required Write 42 82 68 ; ADI Required Write 42 FE 88 ; Set CSI Map Address 88 DE 02 ; Power up MIPI D-PHY 88 D2 F7 ; ADI Required Write 88 D8 65 ; ADI Required Write 88 E0 09 ; ADI Required Write 88 2C 00 ; ADI Required Write 88 00 00 ; Power up MIPI CSI-2 Tx 
 (3) schematic

PoornimaSubramani · Accepted Answer

Hi, 
 Please ensure your i2c configuration with below writes, 
 For AIN 1 pin configuration please check the below part in ADV7280M_Cust-VER.4.1.txt 
 ##CVBS AUTODETECT## 
 :AUTODETECT CVBS Single Ended In Ain 1, MIPI Out: 
 delay 10 ; 
 42 0F 00 ; Exit Power Down Mode 
 42 00 00 ; INSEL = CVBS in on Ain 1 
 42 0E 80 ; ADI Required Write 
 42 9C 00 ; ADI Required Write 
 42 9C FF ; ADI Required Write 
 42 0E 00 ; Enter User Sub Map&ensp; 
 42 03 4E ; ADI Required Write 
 42 04 57 ; Power-up INTRQ pin 
 42 13 00 ; Enable INTRQ output driver 
 42 17 41 ; select SH1 
 42 1D C0 ; Tri-State LLC output driver 
 42 52 CD ; ADI Required Write 
 42 80 51 ; ADI Required Write 
 42 81 51 ; ADI Required Write 
 42 82 68 ; ADI Required Write 
 42 FE 88 ; Set CSI Map Address 
 88 DE 02 ; Power up MIPI D-PHY 
 88 D2 F7 ; ADI Required Write 
 88 D8 65 ; ADI Required Write 
 88 E0 09 ; ADI Required Write 
 88 2C 00 ; ADI Required Write 
 88 00 00 ; Power up MIPI CSI-2 Tx 
 End 
 Please note that, Default configuration for INSEL register will be on "CVBS input on AIN1" (00000 by default). 
 But please note you need to take care with remaining I2c configuration also (i.e You must program the part with I2C), So please compare your configuration with '##02_CVBS SINGLE ENDED AUTODETECT ##'(Autodetect CVBS Single Ended In AIN1) at 7563.ADV7281_CUST-VER.1.4.txt.zip 
 Also note that the unused analog input pins (Ain X) of analog devices video decoders can be: 
 1) left floating. 
 2) connected via a resistor to ground. 
 3) connected directly to ground. 
 
 Thanks, 
 Poornima)

Electronic Design Services - PartnerZone

Products Mentioned

Color-bar test pattern broken from ADV7280-M