Hi,
We are using ADV7181C and ADV7343 in our design. We want to configure these device for our application. We don't have any Evaluation Board for these decoder and encoder.
Is there any PC software tool for configuring the ADV7181C and ADV7343 Registers without Eval boards? If tools there, please let me know how can I get it for both?
Regards,
Santhosh
These devices are configured over an I2C connection. You will need a USB to I2C adapter such as the Total Phase Aardvark adapter. All this depends on how your hardware is implemented.
At this location: https://ez.analog.com/video/w/documents/801/adv739x-design-support-files
you will find ADV739x_AVES_Files.zip
which contains 4721.ADV739x_Evaluation_Software.zip
which in turn contains ADV7403_XC3S400_ADV7393-VER.1.2c.txt.
that contains multiple format configurations. Only writes to address 0x54 are needed to program the ADV7393. I believe all the formats are defined in the data sheet also.
Here are the support files for the ADV7181C: https://ez.analog.com/video/w/documents/812/adv7181c-design-support-files
And the script files in this attachment:
*************************************** For Rev B Boards *************************************** ##SETTINGS## :version 3.2 May 4th 2010: End ##SD CVBS## :AUTODETECT CVBS IN NTSC/PAL/SECAM, 8-Bit 422 encoder: 42 00 00 ; CVBS IN 42 03 0C ; 8 Bit Mode 42 04 77 ; Enable SFL 42 17 41 ; select SH1 42 1D 47 ; Enable 28MHz Crystal 42 31 02 ; Clears NEWAV_MODE, SAV/EAV to suit ADV video encoders 42 3A 17 ; Set Latch Clock & power down ADC 1 & ADC2 & ADC3 42 3B 81 ; Enable internal Bias 42 3D A2 ; MWE Enable Manual Window, Colour Kill Threshold to 2 42 3E 6A ; BLM optimisation 42 3F A0 ; BGB 42 86 0B ; Enable stdi_line_count_mode 42 F3 01 ; Enable Anti Alias Filter on ADC0 42 F9 03 ; Set max v lock range 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 7F FF ; ADI Recommended Setting 42 81 30 ; ADI Recommended Setting 42 90 C9 ; ADI Recommended Setting 42 91 40 ; ADI Recommended Setting 42 92 3C ; ADI Recommended Setting 42 93 CA ; ADI Recommended Setting 42 94 D5 ; ADI Recommended Setting 42 B1 FF ; ADI Recommended Setting 42 B6 08 ; ADI Recommended Setting 42 C0 9A ; ADI Recommended Setting 42 CF 50 ; ADI Recommended Setting 42 D0 4E ; ADI Recommended Setting 42 D1 B9 ; ADI Recommended Setting 42 D6 DD ; ADI Recommended Setting 42 D7 E2 ; ADI Recommended Setting 42 E5 51 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 56 17 02 ; Software Reset 56 00 FC ; Power up all DAcs and PLL 56 01 80 ; SD only mode, Data input on Y-bus 56 80 10 ; SSAF Luma filter enabled, NTSC mode 56 82 c9 ; Step control on, pixel data valid, pedestal on, PrPb SSAF on,CVBS/YC out. 56 84 06 ; RTCO/SFL Enable 56 88 00 ; 8 bit input enabled 56 87 20 ; Encoder PAL/NTSC auto-detect enabled End ##SDP Y/C## :AUTODETECT Y/C IN NTSC/PAL/SECAM, 8 Bit 422 Encoder: 42 03 0C ; 8 Bit Mode 42 04 57 ; Enable SFL 42 1D 47 ; Enable 28MHz Crystal 42 31 02 ; Clears NEWAV_MODE, SAV/EAV to suit ADV video encoders 42 3A 13 ; Set Latch Clock & turn off ADC2 & ADC3 42 3B 81 ; Enable Internal Bias 42 3D A2 ; MWE Enable Manual Window, Colour Kill Threshold to 2 42 3E 6A ; BLM optimisation 42 3F A0 ; BGB 42 86 0B ; Enable stdi_line_count_mode 42 69 03 ; Sets SDM_SEL to 03 for YC/CVBS Auto 42 F3 03 ; Enable Anti Alias Filters on ADC0 & ADC1 42 F9 03 ; Set max v lock range 42 C4 80 ; Enable maual input muxing 42 C3 C2 ; Enable manual input muxing 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 7F FF ; ADI Recommended Setting 42 81 30 ; ADI Recommended Setting 42 90 C9 ; ADI Recommended Setting 42 91 40 ; ADI Recommended Setting 42 92 3C ; ADI Recommended Setting 42 93 CA ; ADI Recommended Setting 42 94 D5 ; ADI Recommended Setting 42 B1 FF ; ADI Recommended Setting 42 B6 08 ; ADI Recommended Setting 42 C0 9A ; ADI Recommended Setting 42 CF 50 ; ADI Recommended Setting 42 D0 4E ; ADI Recommended Setting 42 D1 B9 ; ADI Recommended Setting 42 D6 DD ; ADI Recommended Setting 42 D7 E2 ; ADI Recommended Setting 42 E5 51 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 56 17 02 ; Software Reset 56 00 FC ; Power up all DAcs and PLL 56 01 80 ; SD only mode, Data input on Y-bus 56 80 10 ; SSAF Luma filter enabled, NTSC mode 56 82 c9 ; Step control on, pixel data valid, pedestal on, PrPb SSAF on,CVBS/YC out. 56 84 06 ; RTCO/SFL Enable 56 88 00 ; 8 bit input enabled 56 87 20 ; Encoder PAL/NTSC auto-detect enabled End ##SDP YPrPb## :AUTODETECT YPbPr In, 8 Bit 422 Encoder: 42 8D 83 ; Fix for Connect/Disconnect Problem 42 00 09 ; YPrPb 42 03 0C ; 8 Bit Mode 42 1D 47 ; Enable 28MHz Crystal 42 27 18 ; YC Delay Correction 42 31 02 ; Clears NEWAV_MODE, SAV/EAV to suit ADV video encoders 42 3A 11 ; set latch clock settings to 001b, Power Down ADC3 42 3B 81 ; Enable internal Bias 42 3D A2 ; MWE Enable Manual Window 42 3E 6A ; BLM optimisation 42 3F A0 ; ADI Recommended 42 86 0B ; Enable stdi_line_count_mode 42 B4 F9 ; Fix for Connect/Disconnect Problem 42 B5 00 ; Fix for Connect/Disconnect Problem 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 F3 07 ; Enable Anti Alias Filters on ADC 0,1,2 42 F9 03 ; Set max v lock range 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 7F FF ; ADI Recommended Setting 42 81 30 ; ADI Recommended Setting 42 90 C9 ; ADI Recommended Setting 42 91 40 ; ADI Recommended Setting 42 92 3C ; ADI Recommended Setting 42 93 CA ; ADI Recommended Setting 42 94 D5 ; ADI Recommended Setting 42 7E 73 ; ADI Recommended Setting 42 B1 FF ; ADI Recommended Setting 42 B6 08 ; ADI Recommended Setting 42 C0 9A ; ADI Recommended Setting 42 CF 50 ; ADI Recommended Setting 42 D0 4E ; ADI Recommended Setting 42 D1 B9 ; ADI Recommended Setting 42 D6 DD ; ADI Recommended Setting 42 E5 51 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 56 17 02 ; Software Reset 56 00 FC ; Power up all DAcs and PLL 56 01 80 ; SD only mode, Data input on Y-bus 56 80 10 ; SSAF Luma filter enabled, NTSC mode 56 82 c9 ; Step control on, pixel data valid, pedestal on, PrPb SSAF on,CVBS/YC out. 56 84 06 ; RTCO/SFL Enable 56 88 00 ; 8 bit input enabled 56 87 20 ; Encoder PAL/NTSC auto-detect enabled End ##SCART RGB## :SCART RGB CP YPrPb 2X1 8 Bit 422 Encoder PAL: 42 03 0C ; 8 Bit Mode 42 04 57 ; Enable SFL 42 06 00 ; 27MHz sample rate 42 1D 47 ; Enable 28MHz Crystal 42 31 02 ; Clears NEWAV_MODE, SAV/EAV to suit ADV video encoders 42 3A 10 ; Set Latch Clock & Power UP ADC 1 & ADC2 & ADC3& ADC4 42 3B 61 ; Enable Internal Bias 42 3D A2 ; MWE Enable Manual Window, Colour Kill Threshold to 2 42 3E 6A ; BLM optimisation 42 3F A0 ; BGB 42 4D EE ; Disable CTI 42 67 01 ; Format 422 42 73 D0 ; Manual Gain Channels A,B,C 42 74 04 ; Manual Gain Channels A,B,C 42 75 01 ; Manual Gain Channels A,B,C 42 76 00 ; Manual Gain Channels A,B,C 42 77 04 ; Manual Offsets A to 64d & B,C to 512 42 78 08 ; Manual Offsets A to 64d & B,C to 512 42 79 02 ; Manual Offsets A to 64d & B,C to 512 42 7A 00 ; Manual Offsets A to 64d & B,C to 512 42 86 0B ; Enable stdi_line_count_mode 42 93 78 ; Clamp optimisation 42 94 23 ; Clamp optimisation 42 95 11 ; Clamp optimisation 42 96 C0 ; Clamp optimisation 42 C5 00 ; Clamp Mode 0 for FB hc based 42 ED C4 ; Enable Static Switching Mode and Select RGB Input 42 F3 0F ; Enable Anti Alias Filter on all ADCs 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 7F FF ; ADI Recommended Setting 42 81 30 ; ADI Recommended Setting 42 90 C9 ; ADI Recommended Setting 42 91 40 ; ADI Recommended Setting 42 92 3C ; ADI Recommended Setting 42 93 CA ; ADI Recommended Setting 42 94 D5 ; ADI Recommended Setting 42 B6 08 ; ADI Recommended Setting 42 C0 9A ; ADI Recommended Setting 42 CF 50 ; ADI Recommended Setting 42 D0 4E ; ADI Recommended Setting 42 D1 B9 ; ADI Recommended Setting 42 D6 DD ; ADI Recommended Setting 42 D7 E2 ; ADI Recommended Setting 42 E5 51 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 42 C4 F5 ; Manual Muxing 42 C3 62 ; Manual Muxing 42 F3 4F ; Manual Muxing 56 17 02 ; Software Reset 56 00 FC ; Power up all DAcs and PLL 56 01 80 ; SD only mode, Data input on Y-bus 56 80 10 ; SSAF Luma filter enabled, NTSC mode 56 82 c9 ; Step control on, pixel data valid, pedestal on, PrPb SSAF on,CVBS/YC out. 56 84 06 ; RTCO/SFL Enable 56 88 00 ; 10 bit input enabled 56 87 20 ; Encoder PAL/NTSC auto-detect enabled 56 8B 40 ; HS to Pixel shift required End ##FAST BLANK## :PAL 10 Bit 422 Encoder: 42 03 00 ; 10 Bit Mode 42 17 41 ; select SH1 42 06 00 ; 27MHz sample rate 42 1D 47 ; Enable 28MHz Crystal 42 31 02 ; Clears NEWAV_MODE, SAV/EAV to suit ADV video encoders 42 3A 10 ; Set Latch Clock & Power UP ADC 1 & ADC2 & ADC3& ADC4 42 3B 61 ; Enable Internal Bias 42 3D A2 ; MWE Enable Manual Window, Colour Kill Threshold to 2 42 3E 6A ; BLM optimisation 42 3F A0 ; BGB 42 67 01 ; Format 422 42 73 D0 ; Manual Gain Channels A,B,C 42 74 04 ; Manual Gain Channels A,B,C 42 75 01 ; Manual Gain Channels A,B,C 42 76 00 ; Manual Gain Channels A,B,C 42 77 04 ; Manual Offsets A to 64d & B,C to 512 42 78 08 ; Manual Offsets A to 64d & B,C to 512 42 79 02 ; Manual Offsets A to 64d & B,C to 512 42 7A 00 ; Manual Offsets A to 64d & B,C to 512 42 86 0B ; Enable stdi_line_count_mode 42 C5 00 ; Clamp Mode 0 for FB hc based 42 ED 12 ; FB_CAP_RES,Enable Dynamic Fast Blank Mode 42 F3 0F ; Enable Anti Alias Filter on all ADCs 42 0E 80 ; ADI Recommended Setting 42 49 01 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 7F FF ; ADI Recommended Setting 42 81 30 ; ADI Recommended Setting 42 90 C9 ; ADI Recommended Setting 42 91 40 ; ADI Recommended Setting 42 92 3C ; ADI Recommended Setting 42 93 CA ; ADI Recommended Setting 42 94 D5 ; ADI Recommended Setting 42 B6 08 ; ADI Recommended Setting 42 C0 9A ; ADI Recommended Setting 42 CF 50 ; ADI Recommended Setting 42 D0 4E ; ADI Recommended Setting 42 D1 B9 ; ADI Recommended Setting 42 D6 DD ; ADI Recommended Setting 42 D7 E2 ; ADI Recommended Setting 42 E5 51 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 42 C4 F5 ; Manual Muxing 42 C3 62 ; Manual Muxing 42 F3 4F ; Manual Muxing 56 17 02 ; Software Reset 56 00 FC ; Power up all DAcs and PLL 56 01 80 ; SD only mode, Data input on Y-bus 56 80 10 ; SSAF Luma filter enabled, NTSC mode 56 82 c9 ; Step control on, pixel data valid, pedestal on, PrPb SSAF on,CVBS/YC out. 56 84 06 ; RTCO/SFL Enable 56 88 00 ; 10 bit input enabled 56 87 20 ; Encoder PAL/NTSC auto-detect enabled 56 8B 40 ; HS to Pixel shift required 74 FC FC ; Power down DAC and HDMI (Bus expander address may vary) End ##CP YPrPb 525i & 625i## :525I YPrPb In 10Bit 422 Encoder: 42 05 00 ; Prim_Mode =000b for SD-M 42 06 0A ; VID_STD=1010b for SD 4x1 525i 42 1D 47 ; Enable 28MHz Crystal 42 3A 11 ; Set Latch Clock 01b, Power Down ADC3 42 3B 81 ; Enable internal Bias 42 3C 52 ; PLL_QPUMP to 010b 42 6B C1 ; Select 422 10 bit YPrPb out from CP 42 7B 06 ; clears the bits CP_DUP_AV and AV_Blank_EN 42 85 19 ; Turn off SSPD and force SOY. For Eval Board. 42 86 1B ; Enable stdi_line_count_mode 42 8F 77 ; FR_LL to 1820 & Enable 28.63MHz LLC 42 90 1C ; FR_LL to 1820 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 C5 01 ; CP_CLAMP_AVG_FACTOR[1-0] = 00b 42 C9 0C ; Enable DDR Mode 42 F3 07 ; Enable Anti Alias Filters on ADC 0,1,2 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 56 17 02 ; Software Reset 56 00 FC ; Power up all DAcs and PLL 56 01 80 ; SD only mode, Data input on Y-bus 56 80 10 ; SSAF Luma filter enabled, NTSC mode 56 82 C9 ; Step control on, pixel data valid, pedestal on, PrPb SSAF on,CVBS/YC out. 56 84 06 ; RTCO/SFL Enable 56 88 10 ; 10 bit input enabled 56 87 20 ; Encoder PAL/NTSC auto-detect enabled End ##CP YPrPb 525i & 625i## :525I YPrPb In 10Bit 422 HS/VS Encoder: 42 05 00 ; Prim_Mode =000b for SD-M 42 06 0A ; VID_STD=1010b for SD 4x1 525i 42 1D 47 ; Enable 28MHz Crystal 42 3A 11 ; Set Latch Clock 01b, Power Down ADC3 42 3B 81 ; Enable internal Bias 42 3C 52 ; PLL_QPUMP to 010b 42 6B C1 ; Select 422 10 bit YPrPb out from CP 42 7B 1C ; Disable AV Codes 42 85 1B ; Turn off SSPD and force SOY. Enable DS_Out For Eval Board. 42 86 1B ; Enable stdi_line_count_mode 42 8F 77 ; FR_LL to 1820 & Enable 27 MHz LLC 42 90 1C ; FR_LL to 1820 42 C5 01 ; CP_CLAMP_AVG_FACTOR[1-0] = 00b 42 C9 0C ; Enable DDR Mode 42 F3 07 ; Enable Anti Alias Filters on ADC 0,1,2 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 56 17 02 ; Software Reset 56 00 FC ; Power up all DAcs and PLL 56 01 80 ; SD only mode, Data input on Y-bus 56 80 10 ; SSAF Luma filter enabled, NTSC mode 56 82 c9 ; Step control on, pixel data valid, pedestal on, PrPb SSAF on,CVBS/YC out. 56 84 06 ; RTCO/SFL Enable 56 88 10 ; 10 bit input enabled 56 87 20 ; Encoder PAL/NTSC auto-detect enabled 56 8A 0C ; H&v 56 8B 40 ; HS to Pixel shift required End ##CP YPrPb 525i & 625i## :525I YPrPb In 12Bit RGB DDR HS/VS HDMI: 42 05 01 ; PRIM_MODE = 001b COMP 42 06 00 ; VID_STD for 525i 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28.63636MHz crystal 42 3A 11 ; Set Latch Clock 01b. Power down ADC3. 42 3B 81 ; Enable Internal Bias 42 3C 53 ; PLL QPUMP to 011b 42 52 04 ; Setup reg 52 to 66 in CSC for RGB color space 42 53 00 ; CSC Register 42 54 78 ; CSC Register 42 55 23 ; CSC Register 42 56 8C ; CSC Register 42 57 C5 ; CSC Register 42 58 BB ; CSC Register 42 59 00 ; CSC Register 42 5A 00 ; CSC Register 42 5B 28 ; CSC Register 42 5C 94 ; CSC Register 42 5D 00 ; CSC Register 42 5E 05 ; CSC Register 42 5F DB ; CSC Register 42 60 00 ; CSC Register 42 61 00 ; CSC Register 42 62 00 ; CSC Register 42 63 01 ; CSC Register 42 64 05 ; CSC Register 42 65 25 ; CSC Register 42 66 DB ; CSC Register 42 6B 84 ; Enable DE output, swap colours 42 C9 08 ; Enable DDR 42 F4 37 ; Set drive strength 42 73 F0 ; Enable Manual Gain and set CH_A gain 42 74 0C ; Set CH_A and CH_B Gain 42 75 03 ; Set CH_B and CH_C Gain 42 76 00 ; Set CH_C Gain 42 77 04 ; Set offset to 64d 42 78 01 ; Set offset to 64d 42 79 00 ; Set offset to 64d 42 7A 40 ; Set offset to 64d 42 7B 1D ; Turn off EAV and SAV Codes. Set BLANK_RGB_SEL. 42 85 19 ; Turn off SSPD and force SOY 42 86 0B ; Enable STDI Line Count Mode 42 B7 1B ; use internal VS width for fixing VS vibration 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 80 ; default color 42 C2 F0 ; Default color 42 0E 80 ; ADI recommended sequence 42 52 46 ; ADI recommended sequence 42 54 00 ; ADI recommended sequence 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI recommended sequence 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 56 00 13 ; Power down Encoder End ##CP YPrPb 525i & 625i## :525I YPrPb In 20Bit 422 HS/VS Encoder: 42 05 00 ; PRIM_MODE = 001b COMP 42 06 0A ; VID_STD for 525i 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28.63636MHz crystal 42 3A 11 ; Set Latch Clock 01b. Power down ADC3. 42 3B 81 ; Enable Internal Bias 42 3C 52 ; PLL QPUMP to 010b 42 6B 81 ; 42 C9 00 ; SDR 42 73 CF ; Enable Manual Gain and set CH_A gain 42 74 A3 ; Set CH_A and CH_B Gain - 0FAh 42 75 E8 ; Set CH_B and CH_C Gain 42 76 FA ; Set CH_C Gain 42 7B 1C ; Turn off EAV and SAV Codes. 42 85 1B ; Turn off SSPD and force SOY 42 86 1B ; Enable STDI Line Count Mode 42 8F 77 ; FR_LL to 1833 & Enable 28.63MHz LLC 42 90 29 ; FR_LL to 1833 42 B7 1B ; use internal VS width for fixing VS vibration 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 F4 37 ; Set drive strength 42 0E 80 ; ADI recommended sequence 42 52 46 ; ADI recommended sequence 42 54 00 ; ADI recommended sequence 42 57 01 ; ADI recommended sequence 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI recommended sequence 56 17 02 ; Software Reset 56 00 FC ; Power up all DAcs and PLL 56 01 80 ; SD only mode, Data input on Y-bus 56 80 10 ; SSAF Luma filter enabled, NTSC mode 56 82 c9 ; Step control on, pixel data valid, pedestal on, PrPb SSAF on,CVBS/YC out. 56 84 06 ; RTCO/SFL Enable 56 88 18 ; 20 bit input enabled 56 86 0A ; 861B timing 56 87 20 ; Encoder PAL/NTSC auto-detect enabled 56 8A 0C ; HS/VS 56 8B 80 ; HS to Pixel shift required End ##CP YPrPb 525i & 625i## :625I YPrPb In 10Bit 422 Encoder: 42 05 00 ; Prim_Mode =000b for SD-M 42 06 0B ; VID_STD=1010b for SD 4x1 525i 42 1D 47 ; Enable 28MHz Crystal 42 3A 11 ; Set Latch Clock 01b, Power Down ADC3 42 3B 81 ; Enable internal Bias 42 3C 52 ; PLL_QPUMP to 010b 42 6B C1 ; Select 422 10 bit YPrPb out from CP 42 7B 06 ; clears the bits CP_DUP_AV and AV_Blank_EN 42 85 19 ; Turn off SSPD and force SOY. For Eval Board. 42 86 1B ; Enable stdi_line_count_mode 42 8A B0 ; Manual VCO_RANGE=01 42 8F 77 ; FR_LL to 1820 & Enable 28.63MHz LLC 42 90 1C ; FR_LL to 1820 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 C5 01 ; CP_CLAMP_AVG_FACTOR[1-0] = 00b 42 C9 0C ; Enable DDR Mode 42 F3 07 ; Enable Anti Alias Filters on ADC 0,1,2 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 56 17 02 ; Software Reset 56 00 FC ; Power up all DAcs and PLL 56 01 80 ; SD only mode, Data input on Y-bus 56 80 11 ; SSAF Luma filter enabled, NTSC mode 56 82 C1 ; Step control on, pixel data valid, PrPb SSAF on,CVBS/YC out. 56 84 06 ; RTCO/SFL Enable 56 88 10 ; 10 bit input enabled 56 87 20 ; Encoder PAL/NTSC auto-detect enabled End ##CP YPrPb 525i & 625i## :625I YPrPb In 12Bit RGB DDR HS/VS HDMI: 42 05 01 ; PRIM_MODE = 001b COMP 42 06 01 ; VID_STD for 525i 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28.63636MHz crystal 42 3A 11 ; Set Latch Clock 01b. Power down ADC3. 42 3B 81 ; Enable Internal Bias 42 3C 53 ; PLL QPUMP to 011b 42 52 04 ; Setup reg 52 to 66 in CSC for RGB color space 42 53 00 ; CSC Register 42 54 78 ; CSC Register 42 55 23 ; CSC Register 42 56 8C ; CSC Register 42 57 C5 ; CSC Register 42 58 BB ; CSC Register 42 59 00 ; CSC Register 42 5A 00 ; CSC Register 42 5B 28 ; CSC Register 42 5C 94 ; CSC Register 42 5D 00 ; CSC Register 42 5E 05 ; CSC Register 42 5F DB ; CSC Register 42 60 00 ; CSC Register 42 61 00 ; CSC Register 42 62 00 ; CSC Register 42 63 01 ; CSC Register 42 64 05 ; CSC Register 42 65 25 ; CSC Register 42 66 DB ; CSC Register 42 6B 84 ; Enable DE output, swap colours 42 C9 08 ; Enable DDR 42 F4 37 ; Set drive strength 42 73 F0 ; Enable Manual Gain and set CH_A gain 42 74 0C ; Set CH_A and CH_B Gain 42 75 03 ; Set CH_B and CH_C Gain 42 76 00 ; Set CH_C Gain 42 77 04 ; Set offset to 64d 42 78 01 ; Set offset to 64d 42 79 00 ; Set offset to 64d 42 7A 40 ; Set offset to 64d 42 7B 1D ; Turn off EAV and SAV Codes. Set BLANK_RGB_SEL. 42 85 19 ; Turn off SSPD and force SOY 42 86 0B ; Enable STDI Line Count Mode 42 B7 1B ; use internal VS width for fixing VS vibration 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 80 ; default color 42 C2 F0 ; Default color 42 0E 80 ; ADI recommended sequence 42 52 46 ; ADI recommended sequence 42 54 00 ; ADI recommended sequence 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI recommended sequence 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 56 00 13 ; Power down Encoder End ##CP YPrPb 525i & 625i## :625I YPrPb In 20Bit 422 HS/VS Encoder: 42 05 00 ; PRIM_MODE = 000b COMP 42 06 0B ; VID_STD for 625i 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28.63636MHz crystal 42 3A 11 ; Set Latch Clock 01b. Power down ADC3. 42 3B 81 ; Enable Internal Bias 42 3C 52 ; PLL QPUMP to 010b 42 6B 81 ; 422 20bit OUT 42 C9 00 ; SDR 42 73 CF ; Enable Manual Gain and set CH_A gain 42 74 A3 ; Set CH_A and CH_B Gain - 0FAh 42 75 E8 ; Set CH_B and CH_C Gain 42 76 FA ; Set CH_C Gain 42 7B 1C ; Turn off EAV and SAV Codes. 42 8A B0 ; Manual VCO_RANGE 01 42 85 1B ; Turn off SSPD and force SOY 42 86 1B ; Enable STDI Line Count Mode 42 8F 77 ; FR_LL to 1833 & Enable 28.63MHz LLC 42 90 29 ; FR_LL to 1833 42 B7 1B ; use internal VS width for fixing VS vibration 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 F4 37 ; Set drive strength 42 0E 80 ; ADI recommended sequence 42 52 46 ; ADI recommended sequence 42 54 00 ; ADI recommended sequence 42 57 01 ; ADI recommended sequence 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI recommended sequence 56 17 02 ; Software Reset 56 00 FC ; Power up all DAcs and PLL 56 01 80 ; SD only mode, Data input on Y-bus 56 80 11 ; SSAF Luma filter enabled, PAL mode 56 82 C1 ; Step control on, pixel data valid, PrPb SSAF on,CVBS/YC out 56 84 06 ; RTCO/SFL Enable 56 86 0A ; 861B timing 56 87 20 ; Encoder PAL/NTSC auto-detect enabled 56 88 18 ; 20 bit input enabled 56 8A 0C ; HS/VS 56 8B 00 ; 56 8C CB ; Subcarrier Frequency PAL 56 8D 8A ; Subcarrier Frequency PAL 56 8E 09 ; Subcarrier Frequency PAL 56 8F 2A ; Subcarrier Frequency PAL End ##CP 525p/625p## :525p/60Hz YPrPb In 12Bit 444 RGB HS/VS HDMI: 42 05 01 ; PRIM_MODE = 001b COMP 42 06 04 ; VID_STD for 525P 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28.63636MHz crystal 42 3A 11 ; Set Latch Clock 01b. Power down ADC3. 42 3B 81 ; Enable Internal Bias 42 3C 53 ; PLL QPUMP to 011b 42 52 04 ; Setup reg 52 to 66 in CSC for RGB color space 42 53 00 ; CSC Register 42 54 78 ; CSC Register 42 55 23 ; CSC Register 42 56 8C ; CSC Register 42 57 C5 ; CSC Register 42 58 BB ; CSC Register 42 59 00 ; CSC Register 42 5A 00 ; CSC Register 42 5B 28 ; CSC Register 42 5C 94 ; CSC Register 42 5D 00 ; CSC Register 42 5E 05 ; CSC Register 42 5F DB ; CSC Register 42 60 00 ; CSC Register 42 61 00 ; CSC Register 42 62 00 ; CSC Register 42 63 01 ; CSC Register 42 64 05 ; CSC Register 42 65 25 ; CSC Register 42 66 DB ; CSC Register 42 6B 84 ; Enable DE output, swap colours 42 C9 08 ; Enable DDR 42 73 F0 ; Enable Manual Gain and set CH_A gain 42 74 0C ; Set CH_A and CH_B Gain 42 75 03 ; Set CH_B and CH_C Gain 42 76 00 ; Set CH_C Gain 42 77 04 ; Set offset to 64d 42 78 01 ; Set offset to 64d 42 79 00 ; Set offset to 64d 42 7A 40 ; Set offset to 64d 42 7B 1D ; Turn off EAV and SAV Codes. Set BLANK_RGB_SEL. 42 85 19 ; Turn off SSPD and force SOY 42 86 0B ; Enable STDI Line Count Mode 42 BF 06 ; Blue Screen Free Run Color 42 C0 40 ; default color 42 C1 80 ; default color 42 C2 F0 ; Default color 42 0E 80 ; ADI recommended sequence 42 52 46 ; ADI recommended sequence 42 54 00 ; ADI recommended sequence 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI recommended sequence 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 56 00 13 ; Power down Encoder End ##CP 525p/625p## :525p/60Hz YPrPb In 20Bit 422 EAV/SAV Encoder: 42 05 01 ; PRIM_MODE = 001b COMP 42 06 06 ; VID_STD for 525P 2x1 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28.63636MHz crystal 42 3A 11 ; Set Latch Clock 01b. Power down ADC3. 42 3B 81 ; Enable Internal Bias 42 3C 53 ; PLL QPUMP to 011b 42 6B 81 ; 422 20bit out 42 C9 00 ; SDR mode 42 73 CF ; Enable Manual Gain and set CH_A gain 42 74 A3 ; Set CH_A and CH_B Gain - 0FAh 42 75 E8 ; Set CH_B and CH_C Gain 42 76 FA ; Set CH_C Gain 42 7B 1E ; Enable EAV and SAV Codes. 42 85 19 ; Turn off SSPD and force SOY 42 86 0B ; Enable STDI Line Count Mode 42 8A B0 ; Manual VCO Range=01 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 C5 01 ; 42 0E 80 ; ADI recommended sequence 42 52 46 ; ADI recommended sequence 42 54 00 ; ADI recommended sequence 42 57 01 ; ADI recommended sequence 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI recommended sequence 56 17 02 ; Software Reset 56 00 1C ; Power up DACs and PLL 56 02 21 ; YPbPr out / Rev.3 operation 861B 56 01 10 ; ED/HD-SDR only mode 56 30 04 ; 525p@60 Frame rate, EAV/SAV 56 31 01 ; H54X enabled, Pixel data valid 56 33 6D ; PrPb SSAF, Sync filter enabled, 422 enabled 56 39 20 ; ED/HD 861B Timing End ##CP 525p/625p## :525p/60Hz YPrPb In 20Bit 422 HS/VS Encoder: 42 05 01 ; PRIM_MODE = 001b COMP 42 06 06 ; VID_STD for 525P 2x1 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28.63636MHz crystal 42 3A 11 ; Set Latch Clock 01b. Power down ADC3. 42 3B 81 ; Enable Internal Bias 42 3C 53 ; PLL QPUMP to 011b 42 6B 81 ; 422 20bit out 42 C9 00 ; SDR mode 42 73 CF ; Enable Manual Gain and set CH_A gain 42 74 A3 ; Set CH_A and CH_B Gain - 0FAh 42 75 E8 ; Set CH_B and CH_C Gain 42 76 FA ; Set CH_C Gain 42 7B 1D ; Turn off EAV and SAV Codes. Set BLANK_RGB_SEL. 42 85 19 ; Turn off SSPD and force SOY 42 86 0B ; Enable STDI Line Count Mode 42 8A B0 ; Manual VCO Range=01 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 C5 01 ; 42 0E 80 ; ADI recommended sequence 42 52 46 ; ADI recommended sequence 42 54 00 ; ADI recommended sequence 42 57 01 ; ADI recommended sequence 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI recommended sequence 56 17 02 ; Software Reset 56 00 1C ; Power up DACs and PLL 56 02 21 ; YPbPr out / Rev.3 operation 861B 56 01 10 ; ED/HD-SDR only mode 56 30 00 ; 525p@60 Frame rate, H&V 56 31 01 ; H54X enabled, Pixel data valid 56 33 6D ; PrPb SSAF, Sync filter enabled, 422 enabled 56 39 20 ; ED/HD 861B Timing End ##CP 525p/625p## :625p/60Hz YPrPb In 20Bit 422 HS/VS Encoder: 42 05 01 ; PRIM_MODE = 001b COMP 42 06 07 ; VID_STD for 625P 2x1 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28.63636MHz crystal 42 3A 11 ; Set Latch Clock 01b. Power down ADC3. 42 3B 81 ; Enable Internal Bias 42 3C 53 ; PLL QPUMP to 011b 42 6B 81 ; 422 20bit out 42 C9 00 ; SDR mode 42 73 CF ; Enable Manual Gain and set CH_A gain 42 74 A3 ; Set CH_A and CH_B Gain - 0FAh 42 75 E8 ; Set CH_B and CH_C Gain 42 76 FA ; Set CH_C Gain 42 7B 1D ; Turn off EAV and SAV Codes. Set BLANK_RGB_SEL. 42 85 19 ; Turn off SSPD and force SOY 42 86 0B ; Enable STDI Line Count Mode 42 8A B0 ; Manual VCO Range=01 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 C5 01 ; 42 0E 80 ; ADI recommended sequence 42 52 46 ; ADI recommended sequence 42 54 00 ; ADI recommended sequence 42 57 01 ; ADI recommended sequence 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI recommended sequence 56 17 02 ; Software Reset 56 00 1C ; Power up DACs and PLL 56 02 21 ; YPbPr out / Rev.3 operation 861B 56 01 10 ; ED/HD-SDR only mode 56 30 18 ; 625p@60 Frame rate, H&V 56 31 01 ; H54X enabled, Pixel data valid 56 33 6D ; PrPb SSAF, Sync filter enabled, 422 enabled 56 39 20 ; ED/HD 861B Timing End ##CP 720p## :720p/60Hz YPrPb In 16Bit 422 EAV/SAV Out Encoder: 42 05 01 ; Prim_Mode =001b COMP 42 06 0A ; VID_STD=1010b for 720P 1x1 42 1D 47 ; Enable 28MHz Crystal 42 3A 21 ; set latch clock settings to 010b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5D ; PLL_QPUMP to 101b 42 6B C3 ; Select 422 16 bit YPrPb out from CP 42 85 19 ; Turn off SSPD and force SOY. For Eval Board. 42 86 1B ; Enable stdi_line_count_mode 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 0E 80 ; Enable Hidden Space. 42 52 46 ; Enable SOG/SOY Clamp Filter 42 54 00 ; CML Level Change 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; Disable Hidden Space. 56 17 02 ; Software Reset 56 00 1C ; Power up DACs and PLL 56 01 10 ; ED/HD-SDR Only mode 56 30 2C ; 720p@60 Frame rate, EAV/SAV codes enabled 56 31 01 ; HD4X enabled, Pixel data valid 56 33 68 ; PrPb SSAF, SINC filter enabled, 8 bit input mode enabled End ##CP 720p## :720p/60Hz YPrPb In 12Bit 444 RGB HS/VS HDMI: 42 05 01 ; Prim_Mode =001b COMP 42 06 0A ;VID_STD=1010b for 720P 1x1 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 21 ; set latch clock settings to 010b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5D ; PLL_QPUMP to 101b 42 52 04 ;setup reg 52 to 66 in CSC for RGB color space 42 53 00 ; CSC Register 42 54 78 ; CSC Register 42 55 23 ; CSC Register 42 56 8C ; CSC Register 42 57 C5 ; CSC Register 42 58 BB ; CSC Register 42 59 00 ; CSC Register 42 5A 00 ; CSC Register 42 5B 28 ; CSC Register 42 5C 94 ; CSC Register 42 5D 00 ; CSC Register 42 5E 05 ; CSC Register 42 5F DB ; CSC Register 42 60 00 ; CSC Register 42 61 00 ; CSC Register 42 62 00 ; CSC Register 42 63 01 ; CSC Register 42 64 05 ; CSC Register 42 65 25 ; CSC Register 42 66 DB ; CSC Register 42 6B 84 ; Enable DE output, swap colours 42 C9 08 ; Enable DDR 42 73 F0 ; Enable Manual Gain and set CH_A gain 42 74 0C ; Set CH_A and CH_B Gain 42 75 03 ; Set CH_B and CH_C Gain 42 76 00 ; Set CH_C gain 42 0E 80 ; Enable Hidden Space. 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; Disable Hidden Space. 42 77 04 ; Set offset to 64d 42 78 01 ; Set offset to 64d 42 79 00 ; Set offset to 64d 42 7A 40 ; Set offset to 64d 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 7C 93 ; set HS position & polarity 42 7D 90 ; set HS position 42 7E 40 ; set HS position 42 85 19 ;Turn off SSPD and force SOY. For Eval Board. 42 86 0B ; Enable stdi_line_count_mode 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 80 ; default color 42 C2 F0 ; Default color 42 C5 01 ; CP_CLAMP_AVG_FACTOR[1-0] = 00b 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 56 00 13 ; Power down Encoder End ##CP 720p## :720p/60Hz YPrPb In 20Bit 422 HS/VS Encoder: 42 05 01 ; Prim_Mode =001b COMP 42 06 0A ; VID_STD=1010b for 720P 1x1 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 21 ; set latch clock settings to 010b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5D ; PLL_QPUMP to 101b 42 6B 81 ; 422 20bit out 42 C9 00 ; SDR 42 73 CF ; Enable Manual Gain and set CH_A gain 42 74 A3 ; Set CH_A and CH_B Gain - 0FAh 42 75 E8 ; Set CH_B and CH_C Gain 42 76 FA ; Set CH_C gain 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 7C 00 ; set HS position & polarity 42 7D 00 ; set HS position 42 7E 00 ; set HS position 42 7F 00 ; 42 85 19 ; Turn off SSPD and force SOY. For Eval Board. 42 86 0B ; Enable stdi_line_count_mode 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 C5 01 ; CP_CLAMP_AVG_FACTOR[1-0] = 00b 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 57 01 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 56 17 02 ; Software Reset 56 00 1E ; Power up DACs and PLL 56 01 10 ; ED/HD-SDR only mode 56 02 21 ; Rev.3 861B timing mode 56 30 28 ; 720p@60 Frame rate, H&V Mode 56 31 01 ; H54X enabled, Pixel data valid 56 33 6D ; PrPb SSAF, SINC filter enabled, 10 bit input mode enabled, 422 Enabled 56 39 20 ; ED/HD 861B Timing End ##CP 720p## :720p/50Hz YPrPb In 20Bit 422 EAV/SAV Encoder: 42 05 01 ; Prim_Mode =001b COMP 42 06 0A ; VID_STD=1010b for 720P 1x1 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 21 ; set latch clock settings to 010b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5D ; PLL_QPUMP to 101b 42 6B 81 ; 422 20bit out 42 C9 00 ; SDR 42 73 CF ; Enable Manual Gain and set CH_A gain 42 74 A3 ; Set CH_A and CH_B Gain - 0FAh 42 75 E8 ; Set CH_B and CH_C Gain 42 76 FA ; Set CH_C gain 42 7B 1E ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 7C 00 ; set HS position & polarity 42 7D 00 ; set HS position 42 7E 00 ; set HS position 42 7F 00 ; 42 85 19 ; Turn off SSPD and force SOY. For Eval Board. 42 86 0B ; Enable stdi_line_count_mode 42 87 E7 ; Reprogram pll_div_ratio for 1080i/50Hz = 1980 42 88 BC ; 42 8F 02 ; Reprogram freerun_line_length also to 764 for 28.636MHz xtal 42 90 FC ; 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 C5 01 ; CP_CLAMP_AVG_FACTOR[1-0] = 00b 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 57 01 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 56 17 02 ; Software Reset 56 00 1E ; Power up DACs and PLL 56 01 10 ; ED/HD-SDR only mode 56 02 21 ; Rev.3 861B timing mode 56 30 34 ; 720p@50 Frame rate, EAV/SAV 56 31 01 ; H54X enabled, Pixel data valid 56 33 6D ; PrPb SSAF, SINC filter enabled, 10 bit input mode enabled, 422 Enabled 56 39 20 ; ED/HD 861B Timing End ##CP 720p## :720p/50Hz YPrPb In 20Bit 422 HS/VS Encoder: 42 05 01 ; Prim_Mode =001b COMP 42 06 0A ; VID_STD=1010b for 720P 1x1 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 21 ; set latch clock settings to 010b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5D ; PLL_QPUMP to 101b 42 6B 81 ; 422 20bit out 42 C9 00 ; SDR 42 73 CF ; Enable Manual Gain and set CH_A gain 42 74 A3 ; Set CH_A and CH_B Gain - 0FAh 42 75 E8 ; Set CH_B and CH_C Gain 42 76 FA ; Set CH_C gain 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 7C 00 ; set HS position & polarity 42 7D 00 ; set HS position 42 7E 00 ; set HS position 42 7F 00 ; 42 85 19 ; Turn off SSPD and force SOY. For Eval Board. 42 86 0B ; Enable stdi_line_count_mode 42 87 E7 ; Reprogram pll_div_ratio for 1080i/50Hz = 1980 42 88 BC ; 42 8F 02 ; Reprogram freerun_line_length also to 764 for 28.636MHz xtal 42 90 FC ; 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 C5 01 ; CP_CLAMP_AVG_FACTOR[1-0] = 00b 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 57 01 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 56 17 02 ; Software Reset 56 00 1E ; Power up DACs and PLL 56 01 10 ; ED/HD-SDR only mode 56 02 21 ; Rev.3 861B timing mode 56 30 30 ; 720p@50 Frame rate, HS/VS 56 31 01 ; H54X enabled, Pixel data valid 56 33 6D ; PrPb SSAF, SINC filter enabled, 10 bit input mode enabled, 422 Enabled 56 39 20 ; ED/HD 861B Timing End ##CP 1080i## :1080i/60Hz YPrPb In 20Bit 422 EAV/SAV Encoder: 42 05 01 ; Prim_Mode =001b COMP 42 06 0C ; VID_STD=1100b for 1125 1x1 42 1D 47 ; Enable 28MHz Crystal 42 3A 21 ; set latch clock settings to 010b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5D ; PLL_QPUMP to 101b 42 6B C1 ; Select 422 20 bit YPrPb out from CP 42 85 19 ; Turn off SSPD and force SOY. For Eval Board. 42 86 1B ; Enable stdi_line_count_mode 42 B7 1B ; use internal VS width for fixing VS vibration 42 BF 0E ; Default Color 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 0E 80 ; Enable Hidden Space. 42 52 46 ; Enable SOG/SOY Clamp Filter 42 54 00 ; CML Level Change 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; Disable Hidden Space. 56 17 02 ; Software Reset 56 00 1C ; Power up DACs and PLL 56 01 10 ; ED/HD-SDR only mode 56 30 6C ; 1080i@30 Frame rate, EAV/SAV codes enabled 56 31 01 ; HD4X enabled, Pixel data valid 56 33 6C ; PrPb SSAF, SINC filter enabled, 20 bit input mode enabled End ##CP 1080i## :1080i/60Hz YPrPb In 12Bit 444 RGB HS/VS HDMI: 42 05 01 ; Prim_Mode =001b COMP 42 06 0C ;VID_STD for 1080i 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 21 ; set latch clock settings to 010b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5D ; PLL_QPUMP to 101b 42 52 04 ; setup reg 52 to 66 in CSC for RGB color space 42 53 00 ; CSC Register 42 54 78 ; CSC Register 42 55 23 ; CSC Register 42 56 8C ; CSC Register 42 57 C5 ; CSC Register 42 58 BB ; CSC Register 42 59 00 ; CSC Register 42 5A 00 ; CSC Register 42 5B 28 ; CSC Register 42 5C 94 ; CSC Register 42 5D 00 ; CSC Register 42 5E 05 ; CSC Register 42 5F DB ; CSC Register 42 60 00 ; CSC Register 42 61 00 ; CSC Register 42 62 00 ; CSC Register 42 63 01 ; CSC Register 42 64 05 ; CSC Register 42 65 25 ; CSC Register 42 66 DB ; CSC Register 42 6B 84 ; Enable DE output, swap colours 42 C9 08 ; Enable DDR 42 73 F0 ; Enable Manual Gain and set CH_A gain 42 74 0C ; Set CH_A and CH_B Gain 42 75 03 ; Set CH_B and CH_C Gain 42 76 00 ; Set CH_C gain 42 77 04 ; Set offset to 64d 42 78 01 ; Set offset to 64d 42 79 00 ; Set offset to 64d 42 7A 40 ; Set offset to 64d 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 7C 53 ; set HS position 42 7D 90 ; set HS position 42 7E 40 ; set HS position 42 85 19 ; Turn off SSPD and force SOY. For Eval Board. 42 86 0B ; Enable stdi_line_count_mode 42 B7 1B ; use internal VS width for fixing VS vibration 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 80 ; default color 42 C2 F0 ; Default color 42 C5 01 ; CP_CLAMP_AVG_FACTOR[1-0] = 00b 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 56 00 13 ; Power down Encoder End ##CP 1080i## :1080i/60Hz YPrPb In 20Bit 422 HS/VS Encoder: 42 05 01 ; Prim_Mode =001b COMP 42 06 0C ;VID_STD for 1080i 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 21 ; set latch clock settings to 010b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5D ; PLL_QPUMP to 101b 42 6B 81 ; 422 20bit OUT 42 C9 00 ; SDR 42 73 CF ; Enable Manual Gain and set CH_A gain 42 74 A3 ; Set CH_A and CH_B Gain - 0FAh 42 75 E8 ; Set CH_B and CH_C Gain 42 76 FA ; Set CH_C gain 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 7C 93 ; set HS position/ HS Polarity - positive 42 7D D4 ; set HS position 42 7E 2D ; set HS position 42 85 19 ; Turn off SSPD and force SOY. For Eval Board. 42 86 1B ; Enable stdi_line_count_mode 42 B7 1B ; use internal VS width for fixing VS vibration 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 C5 01 ; CP_CLAMP_AVG_FACTOR[1-0] = 00b 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 57 01 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 56 17 02 ; Software Reset 56 00 1E ; Power up dacs and PLL 56 01 10 ; ED/HD SDR 56 02 21 ; Rev.3 861B timing mode 56 30 68 ; 1080u@30Hz AV codes disabled 56 31 01 ; H54x enabled, Pixel Data Valid 56 33 6C ; PrPb SSAF, Sync filter enabled, 422 enabled - CbCr swap for old Rev.2 silicon 56 39 20 ; ED/HD 861B Timing End ##CP 1080i## :1080i/50Hz YPrPb In 20Bit 422 EAV/SAV Encoder: 42 05 01 ; Prim_Mode =001b COMP 42 06 0C ; VID_STD for 1080i 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 21 ; set latch clock settings to 010b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5D ; PLL_QPUMP to 101b 42 6B 81 ; 422 20bit OUT 42 C9 00 ; SDR 42 73 CF ; Enable Manual Gain and set CH_A gain 42 74 A3 ; Set CH_A and CH_B Gain - 0FAh 42 75 E8 ; Set CH_B and CH_C Gain 42 76 FA ; Set CH_C gain 42 7B 1E ; Enable EAV & SAV CODES 42 7C 93 ; set HS position/ HS Polarity - positive 42 7D D4 ; set HS position 42 7E 2D ; set HS position 42 85 19 ; Turn off SSPD and force SOY. For Eval Board. 42 86 0B ; Enable stdi_line_count_mode 42 87 EA ; Reprogram pll_div_ratio for 1080i/50Hz = 2640 42 88 50 42 8F 03 ; Reprogram freerun_line_length also to 1018 for 28.636MHz xtal 42 90 FA 42 B7 1B ; use internal VS width for fixing VS vibration 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 C5 01 ; CP_CLAMP_AVG_FACTOR[1-0] = 00b 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 57 01 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 56 17 02 ; Software Reset 56 00 1E ; Power up dacs and PLL 56 01 10 ; ED/HD SDR 56 02 21 ; Rev.3 861B timing mode 56 30 74 ; 1080u@25Hz AV codes 56 31 01 ; H54x enabled, Pixel Data Valid 56 33 6D ; PrPb SSAF, Sync filter enabled, 422 enabled - CbCr swap for old Rev.2 silicon 56 39 20 ; ED/HD 861B Timing End ##CP 1080i## :1080i/50Hz YPrPb In 20Bit 422 HS/VS Encoder: 42 05 01 ; Prim_Mode =001b COMP 42 06 0C ; VID_STD for 1080i 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 21 ; set latch clock settings to 010b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5D ; PLL_QPUMP to 101b 42 6B 81 ; 422 20bit OUT 42 C9 00 ; SDR 42 73 CF ; Enable Manual Gain and set CH_A gain 42 74 A3 ; Set CH_A and CH_B Gain - 0FAh 42 75 E8 ; Set CH_B and CH_C Gain 42 76 FA ; Set CH_C gain 42 7B 1C ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 7C 93 ; set HS position/ HS Polarity - positive 42 7D D4 ; set HS position 42 7E 2D ; set HS position 42 85 19 ; Turn off SSPD and force SOY. For Eval Board. 42 86 0B ; Enable stdi_line_count_mode 42 87 EA ; Reprogram pll_div_ratio for 1080i/50Hz = 2640 42 88 50 42 8F 03 ; Reprogram freerun_line_length also to 1018 for 28.636MHz xtal 42 90 FA 42 B7 1B ; use internal VS width for fixing VS vibration 42 BF 06 ; Blue Screen Free Run Colour 42 C0 40 ; default color 42 C1 F0 ; default color 42 C2 80 ; Default color 42 C5 01 ; CP_CLAMP_AVG_FACTOR[1-0] = 00b 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 57 01 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 56 17 02 ; Software Reset 56 00 1E ; Power up dacs and PLL 56 01 10 ; ED/HD SDR 56 02 21 ; Rev.3 861B timing mode 56 30 70 ; 1080u@25Hz AV codes disabled 56 31 01 ; H54x enabled, Pixel Data Valid 56 33 6C ; PrPb SSAF, Sync filter enabled, 422 enabled - CbCr swap 56 39 20 ; ED/HD 861B Timing End ##CP VGA 640x480## :640x480 _@ 60 Autodetecting sync source 25.175MHz Out through HDMI: 42 05 02 ; Prim_Mode =010b for GR 42 06 08 ; VID_STD=1000b for 640x480 @ 60 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 11 ; set latch clock settings to 001b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5C ; PLL_QPUMP to 100b 42 6A 00 ; DLL Phase Adjust 42 6B 84 ; Enable DE output, swap Pr& Pb 42 C9 08 ; Set DDR_EN 42 73 90 ; Set man_gain 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 85 03 ; Enable DS_OUT 42 86 0B ; Enable stdi_line_count_mode 42 8A 90 ; VCO Range to 00b 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 42 52 80 ; ADI Recommended Setting 42 57 08 ; ADI Recommended Setting 42 5B 20 ; ADI Recommended Setting 42 5C 00 ; ADI Recommended Setting 42 62 00 ; ADI Recommended Setting 42 63 01 ; ADI Recommended Setting 42 67 03 ; ADI Recommended Setting 42 68 01 ; ADI Recommended Setting 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 54 00 13 ; Power down Encoder End ##CP VGA 640x480## :640x480 _@ 72 Autodetecting sync source 31.5MHz Out through HDMI: 42 05 02 ; Prim_Mode =010b for GR 42 06 09 ; VID_STD=1000b for 640x480 @ 72 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 11 ; set latch clock settings to 001b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5C ; PLL_QPUMP to 100b 42 6A 00 ; DLL Phase Adjust 42 6B 84 ; Enable DE output, swap Pr& Pb 42 C9 08 ; Set DDR_EN 42 73 90 ; Set man_gain 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 85 03 ; Enable DS_OUT 42 86 0B ; Enable stdi_line_count_mode 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 42 52 80 ; ADI Recommended Setting 42 57 08 ; ADI Recommended Setting 42 5B 20 ; ADI Recommended Setting 42 5C 00 ; ADI Recommended Setting 42 62 00 ; ADI Recommended Setting 42 63 01 ; ADI Recommended Setting 42 67 03 ; ADI Recommended Setting 42 68 01 ; ADI Recommended Setting 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 54 00 13 ; Power down Encoder End ##CP VGA 640x480## :640x480 _@ 75 Autodetecting sync source 31.5MHz Out through HDMI: 42 05 02 ; Prim_Mode =010b for GR 42 06 0A ; VID_STD=1000b for 640x480 @ 72 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 11 ; set latch clock settings to 001b, Power Down ADC3 42 3B 81 ; Enable Internal Bias 42 3C 5C ; PLL_QPUMP to 100b 42 6A 00 ; DLL Phase Adjust 42 6B 84 ; Enable DE output, swap Pr& Pb 42 C9 08 ; Set DDR_EN 42 73 90 ; Set man_gain 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 85 03 ; Enable DS_OUT 42 86 0B ; Enable stdi_line_count_mode 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 42 52 80 ; ADI Recommended Setting 42 57 08 ; ADI Recommended Setting 42 5B 20 ; ADI Recommended Setting 42 5C 00 ; ADI Recommended Setting 42 62 00 ; ADI Recommended Setting 42 63 01 ; ADI Recommended Setting 42 67 03 ; ADI Recommended Setting 42 68 01 ; ADI Recommended Setting 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 54 00 13 ; Power down Encoder End ##CP SVGA 800x600## :RGB 800x600 _@ 56 36MHz Out through HDMI: 42 05 02 ; Prim_Mode =010b for GR 42 06 00 ; VID_STD=0000b for 800x600 _@ 56 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 11 ; set latch clock settings to 001b, Power Down ADC3 42 3B 81 ; Enable External Bias 42 3C 5D ; PLL_QPUMP to 101b 42 6A 00 ; DLL Phase Adjust 42 6B 84 ; Swap Pr & Pb 42 C9 08 ; Set DDR_EN 42 73 90 ; Set man_gain 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 85 03 ; Enable DS_OUT 42 86 0B ; Enable stdi_line_count_mode 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 42 52 80 ; ADI Recommended Setting 42 57 08 ; ADI Recommended Setting 42 5B 20 ; ADI Recommended Setting 42 5C 00 ; ADI Recommended Setting 42 62 00 ; ADI Recommended Setting 42 63 01 ; ADI Recommended Setting 42 67 03 ; ADI Recommended Setting 42 68 01 ; ADI Recommended Setting 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 54 00 13 ; Power down Encoder End ##CP SVGA 800x600## :RGB 800x600 _@ 60 40.000MHz Out through HDMI: 42 05 02 ; Prim_Mode =010b for GR 42 06 01 ; VID_STD=0000b for 800x600 _@ 56 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 11 ; set latch clock settings to 001b, Power Down ADC3 42 3B 81 ; Enable External Bias 42 3C 5D ; PLL_QPUMP to 101b 42 6A 00 ; DLL Phase Adjust 42 6B 84 ; Swap Pr & Pb 42 C9 08 ; Set DDR_EN 42 73 90 ; Set man_gain 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 85 03 ; Enable DS_OUT 42 86 0B ; Enable stdi_line_count_mode 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 42 52 80 ; ADI Recommended Setting 42 57 08 ; ADI Recommended Setting 42 5B 20 ; ADI Recommended Setting 42 5C 00 ; ADI Recommended Setting 42 62 00 ; ADI Recommended Setting 42 63 01 ; ADI Recommended Setting 42 67 03 ; ADI Recommended Setting 42 68 01 ; ADI Recommended Setting 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 54 00 13 ; Power down Encoder End ##CP SVGA 800x600## :RGB 800x600 _@ 72 50.000MHz Out through HDMI: 42 05 02 ; Prim_Mode =010b for GR 42 06 02 ; VID_STD=0000b for 800x600 _@ 56 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 11 ; set latch clock settings to 001b, Power Down ADC3 42 3B 81 ; Enable External Bias 42 3C 5C ; PLL_QPUMP to 100b 42 6A 00 ; DLL Phase Adjust 42 6B 84 ; Swap Pr & Pb 42 C9 08 ; Set DDR_EN 42 73 90 ; Set man_gain 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 85 03 ; Enable DS_OUT 42 86 0B ; Enable stdi_line_count_mode 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 42 52 80 ; ADI Recommended Setting 42 57 08 ; ADI Recommended Setting 42 5B 20 ; ADI Recommended Setting 42 5C 00 ; ADI Recommended Setting 42 62 00 ; ADI Recommended Setting 42 63 01 ; ADI Recommended Setting 42 67 03 ; ADI Recommended Setting 42 68 01 ; ADI Recommended Setting 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 54 00 13 ; Power down Encoder End ##CP SVGA 800x600## :RGB 800x600 _@ 75 49.500MHz Out through HDMI: 42 05 02 ; Prim_Mode =010b for GR 42 06 03 ; VID_STD=0000b for 800x600 _@ 56 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 11 ; set latch clock settings to 001b, Power Down ADC3 42 3B 81 ; Enable External Bias 42 3C 5C ; PLL_QPUMP to 100b 42 6A 00 ; DLL Phase Adjust 42 6B 84 ; Swap Pr & Pb 42 C9 08 ; Set DDR_EN 42 73 90 ; Set man_gain 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 85 03 ; Enable DS_OUT 42 86 0B ; Enable stdi_line_count_mode 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 42 52 80 ; ADI Recommended Setting 42 57 08 ; ADI Recommended Setting 42 5B 20 ; ADI Recommended Setting 42 5C 00 ; ADI Recommended Setting 42 62 00 ; ADI Recommended Setting 42 63 01 ; ADI Recommended Setting 42 67 03 ; ADI Recommended Setting 42 68 01 ; ADI Recommended Setting 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 54 00 13 ; Power down Encoder End ##CP XGA 1024x768## :RGB 1024x768 _@ 60Hz 12-Bit DDR 65.000MHz Out through HDMI: 42 05 02 ; Prim_Mode =010b for GR 42 06 0C ; VID_STD=1100b for 1024x768 _@ 60 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 21 ; set latch clock settings to 010b, Power Down ADC3 42 3B 61 ; Enable Internal Bias 42 3C 5D ; PLL_QPUMP to 101b 42 6A 00 ; DLL Phase Adjust 42 6B 84 ; Swap Pr & Pb 42 C9 08 ; Set DDR_EN 42 73 90 ; Set man_gain 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 85 03 ; Enable DS_OUT 42 86 0B ; Enable stdi_line_count_mode 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 42 52 80 ; ADI Recommended Setting 42 57 08 ; ADI Recommended Setting 42 5B 20 ; ADI Recommended Setting 42 5C 00 ; ADI Recommended Setting 42 62 00 ; ADI Recommended Setting 42 63 01 ; ADI Recommended Setting 42 67 03 ; ADI Recommended Setting 42 68 01 ; ADI Recommended Setting 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 56 00 13 ; Power down Encoder End ##CP XGA 1024x768## :RGB 1024x768 _@ 70Hz 12-bit DDR 75.000MHz Out through HDMI: 42 05 02 ; Prim_Mode =010b for GR 42 06 0D ; VID_STD=1101b for 1024x768 _@ 70 42 C3 46 ; ADC1 to Ain4, ADC0 to Ain6, 42 C4 B5 ; ADC2 to Ain5 and enables manual override of mux 42 1D 47 ; Enable 28MHz Crystal 42 3A 21 ; set latch clock settings to 010b, Power Down ADC3 42 3B 61 ; Enable Internal Bias 42 3C 5E ; PLL_QPUMP to 110b 42 6A 00 ; DLL Phase Adjust 42 6B 84 ; Select 444 12 bit YCrCb out from CP 42 C9 08 ; Set DDR_EN 42 73 90 ; Set man_gain 42 7B 1D ; TURN OFF EAV & SAV CODES Set BLANK_RGB_SEL 42 85 03 ; Enable DS_OUT 42 86 0B ; Enable stdi_line_count_mode 42 F4 3F ; Max Drive Strength 42 0E 80 ; ADI Recommended Setting 42 52 46 ; ADI Recommended Setting 42 54 00 ; ADI Recommended Setting 42 F6 3B ; ADI Recommended Setting 42 0E 00 ; ADI Recommended Setting 42 52 80 ; ADI Recommended Setting 42 57 08 ; ADI Recommended Setting 42 5B 20 ; ADI Recommended Setting 42 5C 00 ; ADI Recommended Setting 42 62 00 ; ADI Recommended Setting 42 63 01 ; ADI Recommended Setting 42 67 03 ; ADI Recommended Setting 42 68 01 ; ADI Recommended Setting 7A 41 10 ; Power up 7A 01 03 ; 20N bytes of CTS audio Clk 7A 03 18 ; 20N bytes of CTS audio Clk 7A 0A 64 ; Mclk setup,Refresh rate settings. 7A 0C 0C ; I2S Setup, Format 7A 15 0A ; 12-bit DDR In 7A 16 02 ; 12-bit style1 rising edge 7A 17 08 ; CSC coeffients +-2 (8192_8190) 7A 44 F8 ; SPDIF enable 7A 45 C0 ; Clear AV Mute 7A 46 04 ; Aspect Ratio 16_9 7A 50 60 ; Audio Channel Count 7A 51 90 ; Speaker mapping 7A 96 20 ; Interrupt action for VS 7A 98 03 ; RSVD 7A 9E 10 ; RSVD 7A A0 00 ; RSVD 7A AF 06 ; set HDMI Mode 7A BA E0 ; Input Video clk(negedge) 7A CB 01 ; RSVD 74 F5 F5 ; Power down DAC (Bus expander address may vary by board) 56 00 13 ; Power down Encoder End
Writes to address 0x42 are ADV7181C writes
