Products In This Thread

AD9889B Not Recommended for New Designs
The AD9889B is a 165 MHz, high definition multimedia inter-face (HDMI®) v. 1.3 transmitter. It supports HDTV formats up to 1080p, and computer graphic...
Datasheet
AD9889B on Analog.com

  • State Verified Answer
  • Replies 13 replies
  • Subscribers 81 subscribers
  • Views 2111 views
  • Users 0 members are here
Options
Related 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
AD9889B and 1080p60 problem



		

			

									
					    Jacky-zheng
					
							

			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Jul 1, 2012 
				
			
			
		
    

				
		
    
		    		    
		    
		    	
			
    Hello,
    
 
    I am using an AD9889B,sucessfully transmitting 720p60 and 480p60 signals.
    
 
    Now I tried to transmit 1080p60.
    
 
    AD9889B corrently recognizes the mode that I send to it by reading these registers(R0x3D=0x10,R0x41=0xF8,R0x42=0x10,all circuits powered up and Hot plug active),but the display is black.I've tried many diffrent displays(samsung and others),all displays are black.
    
 
    I modify R0xA2 and R0xA3 to 0X87,and change the timing sequence following EIA-CEA-861-D(verified with a scope),and using videoclock of 148.5MHz,but it's not working.
    
 
    I've tried 1280*768 60Hz too,the videoclock of 108MHz,the display is sign good and black from time to time.
    
 
    I am not using HDCP.
    
 
    Any other regiter must be modfied?
    
 
    many thanks
    
 
    Tom
    
								
    

				
				
		
    
			
						
									
									
						
						
			
			
			
			
		
    

        
        

					
    
			
    


    


	
    
		
	
    















    
	
    
	
    
					



			








	
	
	
	



Parents
	
      
	

    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
        
            
			                            
                        
                on Jul 6, 2012 12:19 PM
            
            
					
        
	
        

		
		
        
					
        Hi Dave,
        
 
        I've tested the noise of power supply,The scope told me Vp-p=140mv,I checked document of AD9889B and found noise of power supply=50mv Vp-p, then I go to internet,someone told me the meaning of noise on power supply is about 1/6 of Vp-p, I'm confused???? Counld my power meet the requirement of AD9889B?
        
 
        By the way,Would you please give me the complete details about register setting of AD9889B?
        
 
        I give AD9889B like these:
        
 
        RGB:              4:4:4;  8bit
        
 
        H,V and DE:    separate H,V and DE
        
 
        data bus:         D[23:0]
        
 
        polarity:           High(I'm not sure about this...there's no words to sign polarity of syncs and DE when these signals running separately.
        
 
                                      what's kind of polarity syncs and DE signals AD9889B needed,High or low?)
        
 
        HDCP:             No HDCP
        
 
        Audio:              No audio
        
 
        Output: 1080P@60
        
 
        Output:  720P@60
        
 
        So much appreciation!
        
 
        Tom
        
			
        

		
		
		
		
	
        
	
        
		
        
			
		
        
	
        
	
        
		
						
						
				
						
				
				
		
		
        
			
		
        
	
        

        

        • 

	
      



Reply

        


      • 
	
        



	
		
	
	



        
	
        
		
        
							
					
        
		
        
			
													0
							
			
				
									
							        
			
			
			
          
            
			                            
                        
                on Jul 6, 2012 12:19 PM
            
            
					
          
	
          

		
		
          
					
          Hi Dave,
          
 
          I've tested the noise of power supply,The scope told me Vp-p=140mv,I checked document of AD9889B and found noise of power supply=50mv Vp-p, then I go to internet,someone told me the meaning of noise on power supply is about 1/6 of Vp-p, I'm confused???? Counld my power meet the requirement of AD9889B?
          
 
          By the way,Would you please give me the complete details about register setting of AD9889B?
          
 
          I give AD9889B like these:
          
 
          RGB:              4:4:4;  8bit
          
 
          H,V and DE:    separate H,V and DE
          
 
          data bus:         D[23:0]
          
 
          polarity:           High(I'm not sure about this...there's no words to sign polarity of syncs and DE when these signals running separately.
          
 
                                        what's kind of polarity syncs and DE signals AD9889B needed,High or low?)
          
 
          HDCP:             No HDCP
          
 
          Audio:              No audio
          
 
          Output: 1080P@60
          
 
          Output:  720P@60
          
 
          So much appreciation!
          
 
          Tom
          
			
          

		
		
		
		
	
          
	
          
		
          
			
		
          
	
          
	
          
		
						
						
				
						
				
				
		
		
          
			
		
          
	
          

          

          • 


        


Children
	
        No Data