Along with VDSP installation i have inted client application for BF518F.I need inetd.dpj for BF518F.How can i get that?
Along with VDSP installation i have inted client application for BF518F.
I need inetd.dpj for BF518F.How can i get that?
I suppose the server code is missing. I will notify the team and get back further.
Thanks Prasanth.I need it very much.
I just obtained the code (attached) from our driver team.
Hope this helps.
Message was edited by: Prasanth Rajagopal. Reattaching file.
Thanks a lot.
I just now build and run the program.I got following error.Can you tell me
how can I debug
"Read MAC address from target board failed, a pre-defined MAC address is
can you check the switch settings on your EZ-KIT lite against the LAN Software Readme, and the default switch settings from the EZ-KIT Lite Evaluation System Manual, to ensure these are configured correctly.
You can change this line in lwip_sysboot_threadtype.c to set the predefined MAC address that should be used (your board's MAC address is printed on the underside):
If you check line 96, you will see the address, in flash, where the MAC address is read from on the board. if this address in flash has been overwritten (the default driver should avoid touching this section of memory), you may need to re-write the MAC address to this location.
While building following error is obtained
Creating loader file...
http://ez.analog.com/message/35114#35114/Error ld0095: Unable to open file: ezkitBF527_initcode_ROM-V02.dxe.
1. Tool failed with exit/exception code: 4294967295.
Build was unsuccessful.
i change the load options with ezkitBF518f_initcode_ROM-V00.dxe,ezkitBF518f_initcode_ROM-V01.dxe,ezkitBF518f_initcode_ROM-V02.dxe.
2. then build failed with following error
C:\Program Files (x86)\Analog Devices\VisualDSP 5.0\gmake-378: *** No rule to make target `ADSP-21020, ADSP-21060, ADSP-21061, ADSP-21062,', needed by `Usage'. Stop.
How can I correct this?
for the first error, the path to the "Initialization File" under Project Options: Load would be wrong, as the engineer who provided the example likely had VisualDSP++ installed to a different directory from your setup. Pointing VisualDSP++ to the correct Init Code will help.
For the sectond error, I believe you will have an option that is not correctly wrapped in quotes (i.e. it only has the start quote, or only the end quote). Please check your project options under Project Options: Load, and ensure that any paths are correctly wrapped with both a start and an end quote.
please see the attached file attached which shows register values at error condition
i got following error even if i try to set mac address
I have tested the example here, and it works correctly using VisualDSP++ 5.0 Update 10, together with a Board rev 1.0, BOM rev 1.6, Silicon Rev 0.1 BF518F EZ-KIT Lite board.
Please provide the Board, BOM and Silicon revision of your EZ-KIT Lite. The Board Revision is silk-screened on the PCB, and the BOM revision is available as a sticker on the underside of the board (newer boards only). The Silicon revision is printed directly on the processor itself.
Please also let us know which update of VisualDSP++ 5.0 you are using. e.g. Update 10.
Please open a Blackfin Memory Window via 'Memory'->'Blackfin Memory', and go to address 0x203F0096. Do the values in the 6 memory locations here match the MAC address printed on the underside of your board?
thanks a lot craig .It worked now.
I may need your help later when i integrate the code to run through uart.
I will pre-empt that requirement by directing you to a helpful EE-Note that should give you some tips on adding further devices. EE-312 "Building Complex VDK/LwIP Applications Using Blackfin Processors" details the pitfalls, and how to avoid them, when adding further device drivers (such as UART) to existing LwIP applications, such as ensuring the appropriate resources are allocated.
This is available through the link below, via the 'Application Notes' link:
Retrieving data ...