I use the DVP Eval Latest Source 10-14-11 running adv7280-M, when i program the adv7280-M evaluation board, the Board Connected show red, and Device Scanner can not detect the USB. I do not why? Can you help me, thank you!
Did you complete the DVP Eval Program installation with Script files loaded?
When you connect 7.5V supply cable to Jumper J8 on the board, did you observe the D6 LED turns on?
Are you using the USB cable included in the evaluation kit to your computer?
Did you connect the other end of USB cable to Jumper J7 of eval board?
Did you observe LED D7 turns on this stage?
Yes, I do all the work according to the ADV7280-M Installation Guide step by step. Now I am doing the step: 2.6. PROGRAM THE ADV7280-M EVALUATION BOARD. When I press the Load button. A console similar to that shown in Figure 6 appears. But the Board Connected shows red, and many function can't operation. I don't know why? Can you help me? Thanks！
Please check whether you are using proper USB cables
Also check whether the installation is done correctly. If not do it once again and make sure that the files are downloaded correctly from FTP
Give a snapshot of what you are getting
Are you have the cy7c68013a driver? Can you give me transfer a driver? I think that is my USB driver installation is not correct.My email: email@example.com or firstname.lastname@example.org. Thanks!
Please follow the thread ADV7281-M EVB USB driver
Similar issue posted. Jumper made the problem. Please check whether this helps you.
Hi,The DVP Eval Latest Source 10-14-11 can be used for win10 system? Because my operating system is win10 system. Thank you.
Best Regards,ZQ, H
May be, but not sure. Please try to do it in windows 7 PC and check it. In the other thread saying starting the tool as an administrator in Windows 7. Please try this also.
Hi, Jeyasudha.MI tried in windows 7 PC. But it is still the problem above. 'Board Disconnected' shows red. I think this is my USB driver problem. But I don't know how to set up the drive. Can you help me. Thank you!
This is my main USB driver code:
;for all platforms[Device]%VID_04B4&PID_8613.DeviceDesc%=CyUsb, USB\VID_04B4&PID_8613
;for windows 2000 non intel platforms[Device.NT]; Cypress FX2LP default ID%VID_04B4&PID_8613.DeviceDesc%=CyUsb, USB\VID_04B4&PID_8613
; Cypress FX1 default ID%VID_04B4&PID_8613.DeviceDesc%=CyUsb, USB\VID_04B4&PID_8613
;for x86 platforms[Device.NTx86]; Cypress FX2LP default ID%VID_04B4&PID_8613.DeviceDesc%=CyUsb, USB\VID_04B4&PID_8613
;for x64 platforms[Device.NTamd64]; Cypress FX2LP default ID%VID_04B4&PID_8613.DeviceDesc%=CyUsb, USB\VID_04B4&PID_8613
; Cypress FX1 default ID%VID_04B4&PID_8613.DeviceDesc%=CyUsb, USB\VID_04B4&PID_8613...
CYUSB_Provider = "Cypress"
CYUSB_Company = "Cypress Semiconductor Corporation"
CYUSB_Description = "Cypress Generic USB Driver"
CYUSB_DisplayName = "Cypress USB Generic"
CYUSB_Install = "Cypress CYUSB Driver Installation Disk"
VID_04B4&PID_8613.DeviceDesc="Cypress EZ-USB FX2LP No EEPROM"
VID_04B4&PID_8613.DeviceDesc="Cypress EZ-USB FX1 - No EEPROM"
VID_04B4&PID_8613.DeviceDesc="Cypress EZ-USB Example Device"
VID_04B4&PID_8613.DeviceDesc="Cypress EZ-USB Streamer Device"
VID_04B4&PID_8613.DeviceDesc="Cypress USB Generic Driver (3.4.4.000)"
CYUSB_Unused = "."
Were you able to resolve the problem in your side? I could see that follow up posted on the thread ADV7281-M EVB USB driver and did you follow the same?
I have done follow up posted on the thread ADV7281-M EVB USB driver. But I still have not solve this problem.
I have a question. The all procedures and firmware have been flashed in the development board in advance? Who can tell me. Thank you!
Yes, the evaluation boards come with software programmed on them.
Can you confirm that the LED by the power connector is enabled?
Can you confirm that the LED by the USB is enabled?
When you plug the board in to your computer, does it appear in device manager?
Can you try running the software in a Windows 7 compatibility mode? We have not yet proven this software on Windows 10.
When you open the software and run the I2C scanner (Tools -> Device Scanner), does it identify any devices?
Retrieving data ...