• adxl372 read -15~15 (100mg) at nomal status

    with no impact or moving, adxl372 reads -15~15 [100mg] accelation range.

    it’s about 1.5g, and i think it is big. 

    is this normal range?

    and with just 1cm drop of pcb, the max peak reads 1300 [100mg].

    i am confused if it is right value.

    how can…

  • 2009-10-03 15:49:15     linphone: G722 audiocodec

    2009-10-03 15:49:15     linphone: G722 audiocodec

    Andreas Neubacher (AUSTRIA)

    Message: 80820   

    hi,

    linphone is currently not supporting the wideband audiocodec G722, but i've found some several forum-entries about implementing this codec to linphone…

  • 2010-06-15 15:30:38     request_irq(IRQ_UART0_TX) fails

    2010-06-15 15:30:38     request_irq(IRQ_UART0_TX) fails

    Steven Vacca (UNITED STATES)

    Message: 90327   

    Hi,

    I have a BF-537.

    In my driver, I am able to successfully request an IRQ for UART0_RX,  request_irq(IRQ_UART0_RX),  but get failure when trying to…

  • 2008-03-01 15:15:07     Question about blackfin_cam.c

    2008-03-01 15:15:07     Question about blackfin_cam.c

    Frank Van Hooft (CANADA)

    Message: 51957    I'm working my way through the blackfin_cam.c file as an educational exercise. I understand this is an example V4L1 driver, and the preferred method is V4L2…

  • 2008-09-30 15:15:01     buildind uclinux from trunk

    2008-09-30 15:15:01     buildind uclinux from trunk

    Omar Chanouha (UNITED STATES)

    Message: 62949   

    My setup: toolchain, uclibc, dist = r1.5 on fedora 9. I make menuconfig and selected BF548-ezkit and then answered 'default' to all the config questions…

  • 2008-01-15 15:42:35     network info at boot

    2008-01-15 15:42:35     network info at boot

    ketan bhardwaj (INDIA)

    Message: 49613    hello all,

    Can we automate passing of network info such as IP, DNS, GW from uboot to kernel?

    or how can we ensure that the previous settings remain after re booting also…

  • 2009-07-15 15:03:33     SPORT I/O Speeds

    2009-07-15 15:03:33     SPORT I/O Speeds

    Matthew Barousse (UNITED STATES)

    Message: 77404   

    Hey All,

    I have an ADC (AD7683) hooked up to SPORT0 and a DAC (AD5663) hooked up to SPORT1. As a simple system test I'm reading in samples from the ADC and formatting…

  • 2009-06-15 15:25:47     BF537 ezkit lite & AD73322

    2009-06-15 15:25:47     BF537 ezkit lite & AD73322

    Adrien Cottenceau (CANADA)

    Message: 75750   

    I have a BF537 ezkite lite and a custom sound card on SPORT1 with 3 cascaded AD73322.

    I'm using the Blackfin kernel driver AD73322,  with some changes…

  • AD9914/15 Bit 15:8 of CFR4 reads 0x21 after reset

    On an AD9915, bit 15:8 of CFR4 reads 0x21 after reset. But the Rev A DS states: "Requires register default value settings (0x31)" on page 36.


    Which one is correct? Or should the bits read 0x21, but require 0x31 on writes?

  • 2008-05-15 15:02:24     Any jpeg compressor on uClinux?

    2008-05-15 15:02:24     Any jpeg compressor on uClinux?

    Hadi Boulfelfel (FRANCE)

    Message: 55865   

    Hi,

    please,  is there any JPEG compressor application or source to be build on the uClinux dist?

    thank you,

    best regards,

    Hadi

    TranslateQuoteReplyEd…