• Buck circuit using LTC3810, its output current increase significantly.

    Hi !

    I'm beginer hardware engineer and for a power supply project we are very interested in your regulator controller. The LTC3810 is typically a component we are interested in to regulate 51V to 34V at 12V while providing 6A.

    We immediately bought…

  • LTC3810芯片没有输出

    供电电压48V，测试INTVCC处电压为10V，BOOST处电压为9.6V，FB和SW处电压为0V，VON处和VRNG处电压为10V，NDRV处电压为13V左右，ION处电压为1.33V，没有输出电压，请帮忙分析一下怎么解决！非常感谢！

  • LTC3810 Dead Time

    Referring Data sheet 3810fc for LTC3810 I can not find the specification of dead time between main output FET operations.  So how does one determine the largest gate charge that can be switched quickly enough?

  • LTC3810控制器技术

    在设计一款84-50V的DC-DC同步降压变换器（设计工作频率1MHz,最大输出功率100W）中，采用了贵公司的LTC3810作为控制器。在使用中，遇到了一些问题，所以想咨询下有没有相关的解决办法。
          目前遇到的主要问题就是，在开环测试及轻负载测试时，输出电压能够稳定输出约为50V，在输出电流约大于0.5A时，开启电子负载之后，输出电压降低，然后保持稳定（典型测试结果为当输出电流为0.5A，输出电压降至47V；当输出电流为0.6A，输出电压降至45V）。设计的电路原理图如附件所示。
          我们也调节了环路稳定的端口…

  • LTC3810 - Constant Current Mode CC - possible?

    hi guys,

    how i have to design the ltc3810 circuit layout to get a constant current limited output? 

    1. we use a precast pcb product design

    2. we configurated the output voltage over the Vfb Voltage divider to 29,28V output CV

    3. we try to limit the output…

  • LTC3810 constant current with fix voltage limit?

    hi guys,

    how i have to design the ltc3810 circuit layout to get a constant current limited output? 

    1. we use a precast pcb product design

    2. we configurated the output voltage over the Vfb Voltage divider to 29,28V output CV

    3. we try to limit the output…

  • A Buck circuit using LTC3810 as conrtrol model, its output voltage decreases significantly as the output current increases, along with the decline of the system switch frequency.

    1. the schematic of the application

    Vin=84V, Vout=50V,fsw=1.04MHz,full load current is 2A.

    control section: LTC3810

    driver section:LMG1210

    Switch transistor: high side:EPC 2012C   low side: EPC 2012C

    2. The problem we were faced with in the experiment…

  • Required Odb++ for development board DC-952A to access EMI performance

    Hello,

    Engineers Forum,

    Analog Devices.

                              I am a Senior Electronic Designer from Simyog Technology Pvt.Ltd, a start-up from Bangalore, India and funded by Robert Bosch, India. In one of our applications for Automotive electronics, We would like…

  • LTSPICE Simulation error

    Dear Team,

    Please help me find out what is going wrong in the LT spice Simulation.

    I have attached my Simulation file.

    My Input is 28VDC and I need a variable output (1.5V to 15V @10A).

    A 20K digital potentiometer will be used as feedback resistor(RFB2…

  • About the LTC3895 FET

    I am designing a circuit using the LTC3895.

    Why is not the provision of "BG, TG RMS Currents" in LTC3895?
    For example, the LTC3810 has the following.

    <---

    FET is thinking of IPP50N10S3L-16 (infineon).
    Qg (Gate charge total) is 64nC, is this…