• RE: LT6604-2.5的增益最大可设置到多少?

    您好,关于LT6604-2.5的问题请您发布在咱们的全球技术社区哦ez.analog.com/.../

  • RE: I want to synchronize two DDS AD9912 sinusoidal outputs and make them by 90 degree phase shift

    thank you ,

    as you said the last comment you mentioned about the ad9913 for the second paragraph . But i chose the AD9912 as it have maximum DAC bits, FTW etc. But according to the equations and all your first comment was right as the minimum…

  • LTC2470 reading jumps by 15

    I'm using the LTC2470 to read the output of an analog hall effect sensor and it is working fine except that the reading jumps by steps of about 15 numerically as the sensor output changes (I assume 4 bits). Is there some reason why the 4 lowest bits would…

  • ADuC7026 XMxPAR[15] behavior

    Hi All,

    According to datasheet(revF), setting XMxPAR[15] allows byte write capability without using BHE and BLE for two 8 bit memory sharing the same memory region.

    Now, I have following question about this behavior.

    When set XMxPAR as 0xF0FF and write…

  • ADV7513 VIC#15 SCRIPT

    Hello

     

    Im using ADV7513 chip with the below configuration:

    ycbcr 422, 480p 2x clk, de enable (VIC #15)

     

    Tried to use  bt656-ADV7842_7511-hdmi-480pi.txt (with ":8-bit bus separate syncs DE,VS,HS") without luck.

    0x3E is detecting VIC#49 …

  • ADV7513 VIC#15 SCRIPT

    Hello

     

    Im using ADV7513 chip with the below configuration:

    ycbcr 422, 480p 2x clk, de enable (VIC #15)

     

    Tried to use  bt656-ADV7842_7511-hdmi-480pi.txt (with ":8-bit bus separate syncs DE,VS,HS") without luck.

    0x3E is detecting VIC#49 …

  • AD9914/15 POW word

    Hi

    In the AD9914/15 Profiles mode, can anyone confirm that:

    1. The POW word should be calculated according to equation given on page 19 of datasheet

    2. This equation gives a 14 bit word

    3. This word should be stored in the 14 LSB bits of the 16 bits…

  • AD9914/15 PLL pins

    I have a question about the 9914/15 chips -  if the PLL if not used, can the PLL pins be left floating ?

    Also, is it safe to tie the profile, F0/3 mode pins and everything else that should have a static logic level directly to ground or 3.3 DVDD or resistors…

  • 2009-10-03 15:49:15     linphone: G722 audiocodec

    2009-10-03 15:49:15     linphone: G722 audiocodec

    Andreas Neubacher (AUSTRIA)

    Message: 80820   

    hi,

    linphone is currently not supporting the wideband audiocodec G722, but i've found some several forum-entries about implementing this codec to linphone…

  • 2008-10-15 11:15:22     Kernel will not mount JFFS2 - BF561

    2008-10-15 11:15:22     Kernel will not mount JFFS2 - BF561

    John Redford (UNITED KINGDOM)

    Message: 63723   

    Hi, I keep getting the error:

    List of all partitions:

    No filesystem could mount root, tried:

    Kernel panic - not syncing: VFS: Unable to mount…