• ADSP-21062: Using DMA channels 7-8 while BSO bit set (writing to EPROM)

    Hi,

    I have a confusion about using DMA channels while writing to EPROM (BSO bit set). The manual says that I can use DMA channels 7-8 with any packing mode, but then again it says that when the BSO bit is set, PMODE bits are disregarded.

    My questions…

  • Re: how to make serial port of PC to be compatible for serial communication of ADSP 21062

    Hi,

    Could I ask you to provide additional information for this question. Are you simply looking for example application code for communicating - via serial port - between a 21062 target and the PC (e.g. PC running HyperTerminal, or similar host terminal…

  • RE: Bonjour, J'ai un problème de compilation sur un Visual DSP Analog 5.1.2 et un DSP 21062, compilation qui fonctionnait sur les anciens outils Visual. A qui puis je m'adresser

    Hi,

    We understand that you have already contacted our private support.  We are posting the response here for others to benefit:

    These warnings/errors are always issued as a pair and it is the warning to pay heed to as it contains the most relevant information…

  • ACK,RD# and WR# connections in ADSP-21062LCSZ-160

    Hi,

    I am designing ADSP-21062LCSZ-160 +3.3V device in my board. Can you please tell me, whether i need to connect pull-up (180 Ohm) and pull-down (68 Ohm) resistor on ACK,RD# and WR# pin's?

    Because, previously i used +5V device ADSP-21062 and i…

  • How FFT accelerator (FFTA) on ADSP-SC58x/ADSP-2158x is different as compared to ADSP-214xx processors / What are the major features of FFTA on ADSP-SC58x/ADSP-2158x ?

    FFT Accelerator on ADSP-SC58x/ADSP-2158x is a completely new design as compared to the FFT accelerator on ADSP-214xx processors. The major differences/features of the FFT accelerator on ADSPSC58x/ADSP-2158x are:

    • Unlike in ADSP-214xx, the…
  • Porting software  from ADSP-21489 to ADSP-21573 and ADSP-SC573 

    Customer ask some questions.

    Right now we have  plenty of software for ADSP-21489, but it’s quite hard to port it to ADSP-SC573 family. Code itself

    is 99% C and C++.

     

    Does family ADSP-SC573 have interface with external static memory like AMI for ADSP…

  • prototyping the a ADSP-TS203S design with a ADSP-TS201s or a ADSP-TS202S

    We're currently laying out a prototype PCB to take an ADSP-TS203 TigerSHARC
    Processor (i.e. with only a 32 bit cluster bus and 2 link ports). Could we fit
    an ADSP-TS201/2 to this board if we constrict external bus access to 32 bits
  • How DMC/DDR controller in ADSP-SC58x/ADSP-2158x different than DDR2 controller on ADSP-2146x ?

    ADSP-2146x

    ADSP-SC58x/ADSP-2158x

    Supports only DDR2 memory devices Supports DDR3, DDR2, and LPDDR memory devices
    Supports maximum clock/data rate of 225/450 MHz Supports maximum…
  • ADSP-SC5xx/ADSP-215xx

    EngineerZone technical forum that provides customer support for Analog Devices ADSP-SC5xx/ADSP-215xx products.
  • How IIR accelerator on ADSP-SC58x/ADSP-2158x is different than the FIR accelerator on ADSP-214xx?

    The IIR accelerator on ADSP-SC58x/ADSP-2158x works exactly in the same manner except the following differences:

    • Unlike in ADSP-214xx, you don't need to enable the IIR accelerator in PMCTL1 register explicitly in ADSP-SC58x/ADSP-2158x. In fact…