• RE: ADA4853 DISABLE Pin

    This question has been assumed as answered either offline via email or with a multi-part answer. This question has now been closed out. If you have an inquiry related to this topic please post a new question in the applicable product forum.

    Thank you,
  • ADA4853/ADA4430 "disable" pin

    Hey,

     We have both ADA4853-1 and ADA4430-1 on our board.

    in some scenario it can get a 3.3V in the "disable" pin while no voltage applied to the supply (Vs).There are no details in the datasheet (in the A.M.R section ) referes to this case.

  • Are there dual op amps (opamps) with power down / enable / disable function ?

    Are there dual opamp with disable function available?

     

    ADA4895-2:  1 nV/√Hz, Low Power,G≥10 Stable Rail-to-Rail Output Amplifier
     
    http://www.analog.com/en/high-speed-op-amps/high-speed-rail-to-rail-amplifiers/a
    da4895-2/products/product…
  • RE: Is output High-Z when disable? ADA4851-1

    Hi Jay

    Thank you very much for your support.

    Sorry for confusing you.

    Your information is very helpful for me.

    I would like to know about ADA4851-1,especially.

    But I understood that ADA4853 is able to tie the outputs.

    Regards

    Moto

  • AD8324, problems

    Hello,

    I'm building a board with a DSP. The DSP does a FFT on a analog signal. The signal is given a offset and we amplified with a ADA4853-1.

    Then the Signal goes to the AD8324.

    The AD8324 is set in single-ended. The Signal goes to the ADC on…

  • 2*2 MIMO setup

    Hello,

    Iam interested in implementing a MIMO 2*2 scenario where i will use 2 fpgas (1 as the transmitter and 1 as the receiver) where each one  will be connected with one AD-FMCOMMS3-EBZ.
    So the setup will be :
    FPGA_1 + AD-FMCOMMS3-EBZ_1 =Base stati…

  • TAGS LIST: Audio

    AD8024
    AD8509
    AD8511
    AD8531
    AD8532
    AD8534
    AD8565
    AD8566
    AD8567
    AD8614
    AD8644
    ADD8504
    ADD8710
    AD8519
    ADSY8401
    AD8529
    AD1870
    AD1871
    AD1877
    AD1974
    ADAU1977
    ADAU1978
    ADAU1979
    ADAU7002
    SSM2602
    SSM26…
  • ADV7610 registers 4:2:2

    Hello

    Thanks in advance.

    I have a input video signal whose format is: YCbCr (Digital YUV) 20 bit (10 chroma + 10 luma).. 1080p60 (1920x1080 60 fps).

    As I can read in this forum ADV7610 only supports four modes for SDR 4:2:2:

                     - 8 bit SDR ITU-R BT.656…

  • 4:2:2 8bit ycrcb

    Hi,

    I have the EVAL-ADV7612-7511p video evaluation board .I'm using 7612 to receive  HDMI inputs from camera(720p @60) , and then feed to 7511 to output the video to the screen. 

    camera -> 7612 --> 7511 --> screen

    When adv7612 output 4:4:4 8bit ycrcb…

  • RE: ADF4355-2 θjc

    Hi ,

    The ADF4355 assembled in 32ld 5x5mm LFCSP with 3.9mm DAP, Die Size 2.88x3.02mm, on a 2S2P Jedec PCB with 9x thermal vias, delivers the following Thermal parameters;

     

    • Theta Ja: 44.5°C/W
    • Theta Jb: 10°C/W
    • Theta Jc: 22°C/W (Pkg Top) / 4°C/W…