• ADA4622-4 / ADA4622-2 / ADA4622-1 FAQ

    Q1. What is the ADA4622-4 / ADA4622-2 / ADA4622-1?

     

    A1. The ADA4622-4 / ADA4622-2 / ADA4622-1 is the next generation of the AD824 / AD822 / AD820. It is a single supply, 30 V, 8 MHz, Low Bias Current, Single-Supply, RRO, Precision JFET Op Amp.

     

    …

  • ADA4622-1/ADA4622-2 Output Voltage

    I read Datasheet of ADA4622-1/ADA4622-2(Rev. B).

    I have a question.

    The ADA4622-1/ADA4622-2 are the next generation of the AD820 and the AD822 single-supply, rail-to-rail output (RRO),precision junction field effect transistors (JFET) input op amps…

  • ADA4622-1 to replace TI OPA171 issue

    Hello

               Below is customer schematics and ADA4622-1 & TI OPA171 test waveform. The pin3 input signal is DC signal . Why noise is much higher of ADA4622-1 than TI OPA171? It is directly replace OPA171 on the same board for testing. But ADA4622-1 has…

  • Input/output impedance when disabling the ADA4622-1

    I'm curious about the shutdown/disable feature of the ADA4622-1.

    What is the impedance looking into the ADA4622-1 at its inputs and output when the part is in shutdown?  I like the idea of a circuit like Figure 99 of the datasheet, but what extra load…

  • ADA4622 Current Noise Density

    I read Datasheet of ADA4622-1/ADA4622-2/ADA4622-4(Rev. D).

    I have a question.

    IN ELECTRICAL CHARACTERISTICS, VSY = ±15 V  Current Noise Density is 0.8fA/√Hz. (Rev. D | Page 4 of 37)

    I See.

    IN ELECTRICAL CHARACTERISTICS, VSY = ±5 V  

    …

  • ADA4622 Package Information in Specsheet

    In the Page 1 of the specsheet, the final paragraph reads:

    The ADA4622-1 is available in a 5-lead SOT-23 package and an 8-lead LFCSP package

    while in the Page 11 of the specsheet, the page shows:

    Figure 2 and Figure 3, showing the ADA4622-1 in the SOT…

  • About EPAD of ADA4622-2

    Hi,

    I need some help.

    As below picture picked from the datasheet.

    https://www.analog.com/media/en/technical-documentation/data-sheets/ada4622-1-4622-2-4622-4.pdf

    The EPAD of 2ch Version(ADA4622-2)  is recommended to connect the EPAD to V+, but the note…

  • ADA4622 Stability

    Hi.  I'm using an ADA4622 opamp with +/-12v power for a 1Hz to 40kHz preamp feeding an Apex PA78 power amp (see schematic below).  I'm seeing large and quite frequent noise spikes at the preamp output, unless I have a small load capacitance (including…

  • ADA4622-2

    Dear all, 

    I'm considering using  ADA4622-2 as an input buffer in a voltage follower configuration for a medical application. Op-amp will be powered in +/-5V and inputs will be connected to a patient through input resistors.   

    Is there known or foreseeable…

  • ADA4622-4 grade B

    Hi, I am interested in ADA4622-4 opamp grade B but this grade seems not to be available in the 4 opamp package. It is correct?

    Thank you in advance