• Spice Model AD8624 OK?

    Hello,

    When I simulate the AD8624 with a 500 Ohm load resistor, the output is limited to 0.4V.

    The circuit is a differential amplifier with gain 1 using 10kOhm resistors plus a 500Ohm load.

    The design will have only +/-5 supply voltage.

    I have attached…

  • RE: AD8264 crosstalk spec?

    Hi Harry

    Thanks but I was asking about the AD8264 quad differential VGA Amplifier not the AD8624?

    Thanks

    Dave

  • RE: Universal Definition for "No Connect" or "NC"?

    Hi, David.

    Thank you for using ADI products. Regarding your question, the "NC" or "No connect" pins have no internal connections. These pins are provision for improvement for the part's derivative. This means that the "NC" pins of AD8624 in LFCSP maybe…

  • What is the AD8624ARUZ Coefficient of Thermal Expansion (CTE) ?

    What is the AD8624ARUZ Coefficient of Thermal Expansion (CTE) ?

     

    The CTE for AD8624ARUZ is 1.2 x 10E-5/°C
  • 脑电信号采集时多通道间的相互干扰的问题

    尊敬的工程师:

             您好,我用AD8624作为采集EEG信号前面电路时,发现如果其他3个通道悬空,1个通道接触良好时,这个通道会受到其他3个通道 的干扰,如果将这3个通道短接并接地,这个接触良好的通道就好多了,这样我想有个问题就是,在正常采集时,这几个通道间会不会有互相串扰的问题。谢谢。

           另外我想知道互相串扰产生原因,如果能成放大器内部解释更好,

  • Noise optimizing AD8599 &&

    Good day,

    I have a task to optimize noise in BW 10Hz - 10kHz.

    Voltage gain shall be around 20..50. OA connected directly to source of signal,

    which has impedance 1kOm DC and 50Om AC. OA connected to middle point of R1/R2 divider,

    where R1 connected…

  • RE: Need amplifier like OP497 but smaller size

    Hi Kole,

    Do you already have a board fabricated? Can your board accommodate something slightly wider? I believe the AD8624 will perform very closely to the OP497. The size of the IC is 4.4mmx5mm, please see Figure 62 on the datasheet. If you require…

  • RE: 这11大应用领域,你在里面么?

    我最关注领域是通信和消费电子

    我最关注的产品:ADXL345/ADXL362  低失调、高输入阻抗的运放AD8624


    公司产品是手机和智能终端,用到多种sensor,其中加速度传感器是必备的。ADXL345/ADXL362 性能出色,有参考代码,使用非常方便。


  • RE: 【求助】ADMP401 加运放ADA4897-1 电路  Vref取值问题?

    您好。

    REF的值主要取决于后端运放的供电范围以及要放大的信号增益。具体计算可以参考ADI应用笔记AN1165  Supply Voltage一节。

  • RE: AD8220 output voltage

    Hi Scott,

    Thanks for your comments. I confess I've never paid attention to the diamond plots before (not being too sure how to interpret them). From your comment I can now see the answer to part 2 of my question. With a difference input of 40mV (when…