• FAQ. How to ensure synchronization of conversion between multiple AD7124-4/AD7124-8 devices?

    Answer: To ensure synchronization between multiple AD7124-4/AD7124-8 devices, the same master clock must be used for all devices. If the AD7124 internal clock has been used, then one ADC serves as the master and uses its own internal clock and this clock…

  • 关于AD7124-4的问题

    我采用4线制测PT电阻,采用STC8位5V单片机来控制AD7124-4   ,单片机没有焊接里,给AD7124-4供电的1.8V和3.3V正常,焊上单片机后,AD7124供电电压发生变化,为4.25V,请问这是什么 问题?如何解决。在些附件图。

  • AD7124-4 SPI read problem

    Hello,

    I''m trying to read the device ID at 0x05 on the AD7124-4 using an stm32f4 discover board. Here are my initialization and read routines. 

    //initialization

    SPI_InitStruct.SPI_BaudRatePrescaler=SPI_BaudRatePrescaler_256; // This would come…

  • AD7124-4 FS Setting in Virtual Eval Tool

    Hi,

    When I try to set FS = 1 in Virtual Eval Tool for AD7124-4 I get following error: "Fs of 1 is outside range for the AD7124. The Fs for the conditions selected must be between: 4 and 2047. Please enter a valid Fs." But AD7124-4 datasheet says…

  • AD7124-4 DOUT/RDY Pin Toggling

    Hi,

    a similar problem came up in this forum, however i couldn't find a working solution for me.

    The Problem is the SPI communication with the AD7124-4 at 3.3V.

    I use the following setup:

    AVDD = IOVDD = 3.3 V

    AVSS = DGND = GND

    When i run the…

  • FAQ: What is the equation for calculating Internal Temperature Sensor for AD7124-4/AD7124-8 in unipolar mode?

    FAQ: What is the equation for calculating Internal Temperature Sensor for AD7124-4/AD7124-8 in unipolar mode?

    For AD7124-4/AD7124-8 the sensitivity of the internal temperature sensor is 13,584 codes/°C, approximately when Vref = 2.5V. Both unipolar and…

  • Is an IBIS model available for the AD7124-4?

    Q. Is an IBIS model available for the AD7124-4?

    A. There is an IBIS model available for the AD7124-4 that can be downloaded at the following link: http://www.analog.com/en/license/ibis-models?mediaPath=media/en/simulation-models/ibis-models/ad7124…

  • AD7124-4 AD7124-8 ESD on current output pins


    Hi,

    Is there a recommended ESD protection circuit for the current output pins on the AD7124-8?  I am using AIN0 and AIN1 to source 500uA of current to measure a 3 wire RTD.  Since these pins are directly wired off the chip and out of the board they will…

  • AD7124-4单端输入问题


    AD7124-4想把AIN6引脚配置成单端输入,如何配置?通道寄存器,配置寄存器如何配置啊?

  • FAQ. When I need multiple analog input channels, should I use multiple AD7124-4/AD7124 or an external MUX?

    Answer: For a system that requires multiple channels, one AD7124-8 can support up to 8 differential/15 single ended input channels and one AD7124-4 can support up to 4 differential/7 single ended input channels. If the system requires a greater number…