Products In This Thread

AD9375 Recommended for New Designs
The AD9375 is a highly integrated, wideband radio frequency (RF) transceiver offering dual-channel transmitters (Tx) and receivers (Rx), integrated synthesizers...
Datasheet
AD9375 on Analog.com

AD9371 Recommended for New Designs
The AD9371 is a highly integrated, wideband RF transceiver offering dual channel transmitters and receivers, integrated synthesizers, and digital signal...
Datasheet
AD9371 on Analog.com

  • State Not Answered
  • Replies 1 reply
  • Subscribers 18 subscribers
  • Views 593 views
  • Users 0 members are here
Options
Related 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
Algorithm negotiation fail



		

			

									
					    Ivan18
					
							

			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Nov 21, 2022 
				
			
			
		
    

				
		
    
		    		    
		    
		    		            		        
    Category: Software
    
    		        		            		    
    Product Number:  EK-Z7-ZC706-G 
    
    		        		        		        
    Software Version: The lastone
    
    		    		    	
			
    Hi, 
    

    

    I'm using the AD9371 Transceiver Evaluation Software but when I try to connect I have the next error message: Algorithm negotiation fail; Platform problem: Algorithm negotiation fail. On the right botoom corner I have the nextone message: Please update SD card, but I have the last version of OS.
    

    Now, I have a setup with both boards on a AP and my host PC too using DHCP for IP configuration. When I do "ping" between my PC and the boad I get a connection and the other way around as well. I have unzipped the src folder (Wideband RF Transceiver Evaluation Software | Analog Devices) in the directory "/" on my board, I dont have run nothing of this new directory because I dont have read about it.
    

    Regards.
    
									
			        
		
    

				
				
		
    
			
						
									
									
						
						
			
			
			
			
		
    

        
        

					
    
			
    


    


	
    
		
	
    















    
	
    
	
    
					



			








	
	
	
	



Parents
	
      
	

    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
			                            
                        
                on Dec 6, 2022 8:29 AM
            
            
					
      
	
      

		
		
      
					
      Are you using ADI eval board or custom board? TES GUI connects only with our EVB platform. 
      

      Which SD card are you using ? Make sure you use the TES based SD card for windows TES GUI . I hope you are using the same SD-card. Download it from the below link:
      

      https://www.analog.com/en/design-center/landing-pages/001/transceiver-evaluation-software.html
      

      We have two SD-Cards given with the board , Use the one with 'Windows based TES/ ADRV9371-SDCARD' on it.
      

       
      

      Please follow TRANSCEIVER EVALUATION SOFTWARE section  from UG-992 about how to get started with the TES GUI and how to configure the AD9371 TES GUI .Place the SW11 toggle switches in the positions as shown in the below figure (Toggle Switch 1, Toggle Switch 2, and Toggle Switch 5 = Position A.
      

       
      

      Once you power on Is the board booting?  LED will blink in sequence until boot is completed.
      

      Also please refer to the below troubleshooting guide for issues related to TES connection.
      

      
			
      

		
			
	      

		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
				
						
				
				
		
		
      
			
		
      
	
      

      

      • 

	
    



Reply

      


    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
			                            
                        
                on Dec 6, 2022 8:29 AM
            
            
					
      
	
      

		
		
      
					
      Are you using ADI eval board or custom board? TES GUI connects only with our EVB platform. 
      

      Which SD card are you using ? Make sure you use the TES based SD card for windows TES GUI . I hope you are using the same SD-card. Download it from the below link:
      

      https://www.analog.com/en/design-center/landing-pages/001/transceiver-evaluation-software.html
      

      We have two SD-Cards given with the board , Use the one with 'Windows based TES/ ADRV9371-SDCARD' on it.
      

       
      

      Please follow TRANSCEIVER EVALUATION SOFTWARE section  from UG-992 about how to get started with the TES GUI and how to configure the AD9371 TES GUI .Place the SW11 toggle switches in the positions as shown in the below figure (Toggle Switch 1, Toggle Switch 2, and Toggle Switch 5 = Position A.
      

       
      

      Once you power on Is the board booting?  LED will blink in sequence until boot is completed.
      

      Also please refer to the below troubleshooting guide for issues related to TES connection.
      

      
			
      

		
			
	      

		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
				
						
				
				
		
		
      
			
		
      
	
      

      

      • 


    


Children
	
    No Data