Products Mentioned

ADRV9002 Recommended for New Designs
The ADRV9002 is a highly integrated RF transceiver that has dual-channel transmitters, dual-channel receivers, integrated synthesizers, and digital signal...
Datasheet
ADRV9002 on Analog.com

Thread Details

  • State Suggested Answer
  • +1 person also asked this people also asked this
  • Replies 4 replies
  • Answers 2 answers
  • Subscribers 12 subscribers
  • Views 169 views
  • Users 0 members are here
Options
 
Related Content

        

            Post
             Go back to editing
        

    

    


    

    









		


















	
	
			
	
			
		
	
	
		

	    
	    
	    		
DPD Enabling in ADRV9002 transceiver

		
	
				

			

									
					    AnuragD
					
							

            
            			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Jan 9, 2026 
				
			
			
		
    
		
		                     
				
        		
    
		    
		    		    
    
		      		            		        
    Category: Software
    
    		        		            		    
    Product Number:  ADRV9002  
    
    		        		    		    
    
		    		    
		    			
    
			    
    Hi, 
    

    I'm trying to enable DPD(Digital Predistortion) in ARDV9002 transceiver. For this i'm using Transceiver evaluation software (TES) as a GUI, ZCU102 eval board. 
    To enable DPD and analyze the waveform i'm following the below set of steps give in a doc. Also in the file section of a GUI i'm uploading a taxidi file under load session section. But i 'm not getting a desired result after doing so.
    Here i'm attaching a doc containing the sets of steps and also the taxidi file that i'm uploading.
    Kindly look into it and suggest if any correction or modifications  required.

    Regards
    AnuragDOCXDOCX
    
			
    
			
									
		                             
                        

    
    
                                            
                 software
                
                                                    
                 ADRV9002
                
                                                    
                 Wideband Transceiver IC
                
                                                    
                 RF Integrated Transceivers
                
                                
            
    
    
    
		
    

				
				        
        		
    
			
						
									
												
			
			
                        
                                    
                        
                        
                        
            
			            
						
						
			
			
			
			
		
    

        
        
        
    
					
    
			
    


    
















    
	
    
	
    
					



			








	
	
	
	



Parents
	



Reply



Children
	
      
	

    • 
	
      



	
			
		
	



      
	
      
		
      
							
					
      
		
      
		    
		    		    
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
						
                            
            
            				
            
                on Jan 12, 2026 4:47 AM
            
            
												
						in reply to AnuragD
					
										
			            		
      
		
										0
					
	
      

		
		
      
		
      
                                
                                                            
      
					
      Hi Anurag,
      

      

      I noticed that you are using MUX as the FH mode, but in AutoTDD you are referencing the Dual HOP mode timing diagram. Could you please review this section?
      

      

      

       
      

      

      I would also suggest the following steps:
      

      

      1) Avoid loading the previous version of the Taxidi file. Please reconfigure TES manually with the required settings.
      

      

      2) Have you checked the peak power at the ORx port? The ORx attenuation is triggered based on this value, which can impact DPD performance. I assume you have used the provided Python script to obtain the path delay value.
      

      

      

       
      

      3) Capture the signal without DPD and review the gain vs. input signal plot to determine the PA compression. We recommend compressing by approximately 1 dB.
      

      

      

      My recommendation would be to start implementing DPD in defined carrier mode rather than FH mode. Once DPD is working for the desired signal power and settings, you can proceed to FH mode. Please ensure you are familiar with FH mode before enabling DPD.
      

      

      Regards
      

      Rahul
      
			
      

		
			
	      

		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
						
						
				
				
		
		
      
			
		
      
	
      

      

      •