• State Verified Answer
  • Replies 4 replies
  • Subscribers 68 subscribers
  • Views 1510 views
  • Users 0 members are here
Options
Related 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
Wide band mixer and 90deg phase shifter available?



		

			

									
					    FreddyS
					
							

			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Mar 11, 2015 
				
			
			
		
    

				
		
    
		    		    
		    
		    	
			
    HI,  
    
 
    Looking for:
    
 
    a) A wide band mixer that has at least the following characteristics:  
    
 
      
  
    1. Input signal frequency range: DC-5.5 GHz
      2. 
  
    2. LO: 80 MHz
      3. 
  
    3. Output Frequency range: 200-5.5 GHz
      4. 
 
    
 
       The mixer should support the input and output frequency ranges within the same HW (I assume that there might be some degradation in low frequencies
    
 

    
 
      
    
 
    b)  90 degrees phase shift device with the following properties:
    
 
      
  
    1. Very small and low power
      2. 
  
    2. Frequency range: DC-5.5 GHz (or as close to it as possible)
      3. 
 
    
 
       This is for the image rejection mixer implementation.
    
 
      
    
 
     Thanks
    
 
    Freddy
    
								
    

				
				
		
    
			
						
									
									
						
						
			
			
			
			
		
    

        
        

					
    
			
    


    


	
    
		
	
    















    
	
    
	
    
					



			








	
	
	
	



Parents
	
      
	

    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
			                            
                        
                on Mar 11, 2015 7:23 PM
            
            
					
      
	
      

		
		
      
					

      Freddy,
      
 
      You may be able to use a demodulator/modulator combination. You can use the ADL5380 and the ADL5375 with two synthesizers like the ADF4351. The Input would connect to the ADL5380 using LO1 to mix the signal down to a complex IF around 100MHz or so depending on your bandwidth. You can then connect the baseband output of the ADL5380 to the baseband input to the ADL5375 and modulate up to your final frequency using a 2nd LO (LO2). Because the common mode voltage out of the ADL5380 is around 1.5V and the common mode input to the ADL5375 is 0.5V you can not connect them directly but need to use DC  blocking caps and provide a bias voltage to the ADL5375 input. You will also likely want to add baseband filtering to limit spurious outputs.
      
			
      

		
		
		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
				
						
				
				
		
		
      
			
		
      
	
      

      

      • 

	
    



Reply

      


    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
			                            
                        
                on Mar 11, 2015 7:23 PM
            
            
					
      
	
      

		
		
      
					

      Freddy,
      
 
      You may be able to use a demodulator/modulator combination. You can use the ADL5380 and the ADL5375 with two synthesizers like the ADF4351. The Input would connect to the ADL5380 using LO1 to mix the signal down to a complex IF around 100MHz or so depending on your bandwidth. You can then connect the baseband output of the ADL5380 to the baseband input to the ADL5375 and modulate up to your final frequency using a 2nd LO (LO2). Because the common mode voltage out of the ADL5380 is around 1.5V and the common mode input to the ADL5375 is 0.5V you can not connect them directly but need to use DC  blocking caps and provide a bias voltage to the ADL5375 input. You will also likely want to add baseband filtering to limit spurious outputs.
      
			
      

		
		
		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
				
						
				
				
		
		
      
			
		
      
	
      

      

      • 


    


Children
	
    No Data