groupUrl: https://ez.analog.com/power/
Analog.com Analog Dialogue Wiki English
Analog.com Analog Dialogue Wiki 简体中文
EngineerZone
EngineerZone
  • Site
  • User
  • Site
  • Search
  • User
EngineerZone
EngineerZone
  • Log in
  • Site
  • Search
  • Log in
  • Home
  • Blogs ⌵
    • EZ Spotlight
    • The Engineering Mind
  • Browse ⌵
    • All Groups
    • All Members
  • Support ⌵
    • 3D ToF Depth Sensing
    • A2B
    • Aerospace and Defense (ADEF)
    • Amplifiers
    • Analog Microcontrollers
    • Analysis Control Evaluation (ACE) Software
    • Audio
    • Clock and Timing
    • Condition-Based Monitoring
    • Data Converters
    • Design Tools and Calculators
    • Direct Digital Synthesis (DDS)
    • Embedded Vision Sensing
    • Energy Monitoring and Metering
    • FPGA Reference Designs
    • Industrial Ethernet
    • Interface and Isolation
    • Low Power RF Transceivers
    • MEMS Inertial Sensors
    • Motor Control Hardware Platforms
    • Optical Sensing
    • Power Management
    • Precision Technology Signal Chains
    • Processors and DSP
    • Reference Circuits
    • RF and Microwave
    • Signal Chain Power (SCP)
    • Switches/Multiplexers
    • Temperature Sensors
    • Video
    • Wide Band RF Transceivers
    • Wireless Sensor Networks Reference Library
  • About EZ
  • More
  • Cancel
  • 主页
  • 浏览 ⌵
    • 收件箱
    • 个人设置
    • 会员
    • 专区列表
  • 论坛专区 ⌵
    • 放大器专区
    • 精密转换器专区
    • 音频专区
    • ADE电能计量专区
    • MEMS和传感器专区
    • 接口和隔离专区
    • Power 中文专区
    • ADUC微处理器专区
    • 锁相环专区
    • 开关和多路复用器专区
    • 温度传感器
    • 基准电压源专区
    • 资源库
    • 论坛使用指南
    • 技术支持参考库
    • 在线研讨会
    • 论坛社群活动
    • 论坛激励活动
  • More
  • Cancel
Power Management
Power Management
Documents ADP3302: Input protection
  • Q&A
  • Discussions
  • Documents
  • Tags
  • Managers
  • More
  • Cancel
  • New
Power Management requires membership for participation - click to join
  • +Documents
  • +ADIsimPE: FAQ
  • +ADIsimPower: FAQ
  • +ADM1030: FAQ
  • +ADM1031: FAQ
  • +ADM1060: FAQ
  • +ADM1062: FAQ
  • +ADM1064: FAQ
  • +ADM1066: FAQ
  • +ADM1068: FAQ
  • +ADM1069: FAQ
  • +ADM1085: FAQ
  • +ADM1166: FAQ
  • +ADM1171: FAQ
  • +ADM1175: FAQ
  • +ADM1232: FAQ
  • +ADM13305-4: FAQ
  • +ADM1816: FAQ
  • +ADM202: FAQ
  • ADM2483_PV pin function
  • +ADM2484e: FAQ
  • +ADM2486: FAQ
  • +ADM2582E: FAQ
  • +ADM2587E: FAQ
  • +ADM2682E: FAQ
  • +ADM2687E: FAQ
  • +ADM3053: FAQ
  • +ADM3054: FAQ
  • +ADM3075E: FAQ
  • +ADM3202: FAQ
  • +ADM3251E: FAQ
  • +ADM3252E: FAQ
  • +ADM3307: FAQ
  • +ADM3483: FAQ
  • +ADM3485E: FAQ
  • +ADM3491: FAQ
  • +ADM4073T: FAQ
  • +ADM483E: FAQ
  • +ADM485: FAQ
  • +ADM6316: FAQ
  • +ADM6320: FAQ
  • +ADM696: FAQ
  • +ADM706: FAQ
  • +ADM709: FAQ
  • +ADM7151: FAQ
  • +ADM7154: FAQ
  • +ADM8316: FAQ
  • +ADM869L: FAQ
  • +ADN8831: FAQ
  • +ADP-I2C-USB: FAQ
  • +ADP1043A: FAQ
  • +ADP1046: FAQ
  • +ADP1046A: FAQ
  • +ADP1047: FAQ
  • +ADP1048: FAQ
  • +ADP1050: FAQ
  • +ADP1051: FAQ
  • +ADP1055: FAQ
  • +ADP124: FAQ
  • +ADP125: FAQ
  • +ADP130: FAQ
  • +ADP1607: FAQ
  • +ADP160: FAQ
  • +ADP1612: FAQ
  • +ADP1621: FAQ
  • +ADP1741: FAQ
  • +ADP1829: FAQ
  • +ADP1851: FAQ
  • +ADP1870: FAQ
  • +ADP197: FAQ
  • +ADP198: FAQ
  • +ADP2108: FAQ
  • +ADP2118: FAQ
  • +ADP2138CB: FAQ
  • +ADP2384: FAQ
  • +ADP2386: FAQ
  • +ADP2441: FAQ
  • +ADP2504: FAQ
  • +ADP3040: FAQ
  • -ADP3302: FAQ
    • ADP3302: Input protection
  • +ADP3330: FAQ
  • +ADP3338: FAQ
  • +ADP3339: FAQ
  • +ADP3623: FAQ
  • +ADP5046: FAQ
  • +ADP5050: FAQ
  • +ADP5052: FAQ
  • +ADP5053: FAQ
  • +ADP5061: FAQ
  • +ADP5090: FAQ
  • +ADP5585: FAQ
  • +ADP5588: FAQ
  • +ADP5589: FAQ
  • +ADP7112: FAQ
  • +ADP7182: FAQ
  • +ADR01: FAQ
  • +ADR125: FAQ
  • +ADR127: FAQ
  • +ADR225: FAQ
  • +ADR3450: FAQ
  • +ADR365: FAQ
  • +ADR366: FAQ
  • +ADR381: FAQ
  • +ADR5045: FAQ
  • +Digital Power: FAQ
  • +Efficiency Data: FAQ
  • +Generate Negative Supplies: FAQ
  • +Hand Soldering: FAQ
  • How should I connect ADM2483's Power Valid Pin (PVP) when not using it?
  • +LDO: FAQ
  • +Low Noise: FAQ
  • +LT3439: FAQ
  • +Measuring Signals: FAQ
  • +Package Information: FAQ
  • +Photosensitive: FAQ
  • +Power Management Support Intro: FAQ
  • +Switching Power: FAQ
  • +Temperature Grade: FAQ
  • +uPMU: FAQ

ADP3302: Input protection

Q 

Does the ADP3302AR4/5 have reverse input protection, and what will it do to the
battery if it were inserted incorrectly.?  Is there any load dump protection? 
If suitable I would like to use two parts in a dual redundant configuration
with the outputs from one device connected to the outputs of the other device.
the grounds would be common but each device would be fed from seperate
batteries.  Under normal conditions one device would be powered and enabled,
the other device would be powered and the outputs disabled.  What is the
reverse current leakage for the part if it is in shutdown but the output is
forced high by the other device?  If only one device was powered would it back
feed through the unpowered device to it’s input? (i.e. body diode as in mosfet
pass elements).
Would the device be damged if configured in this way?  If both
parts were powered and both outputs enabled at the same time,
how would this affect current drain? and again what is the potential
for damaging the device in this condition.  Supply batteries will
be 6V lithium manganese 1300mAH, initial voltage can be as high
as 7.2V

 

A 

1)Question: Does the ADP3302AR4/5 have reverse input protection?
Answer: ADP3302AR4/5 does not have reverse input protection but we do test and
guarantee for reverse leakage current on the pass transistor.  The test is done
by disabling the device, input is grounded and 12V is applied to the output and
we measure the leakage current of the pass transistor.  The leakage current is
in the order of 30-50nA under these conditions.
2)Question: What will it do to the battery if it were inserted incorrectly?
Answer: When the battery is inserted incorrectly, the ESD protection diode for
ADP3302AR4/5 will turn “on” and start draining current from the battery causing
current flow through the ESD protection diode.  If there is enough current
flows through the ESD diode, it will breakdown the ESD diode.  To prevent the
ESD diode from turning “on” in the event of the battery is inserted
incorrectly, we could place a diode between the battery and input pin.
3)Question: Is there any load dump protection?
Answer: I’m not really clear what your meant by this quesitons but I don’t
thinking our LDOs has load dump protection.  Most of our LDOs operated up to
12V maximum.
4)Question: If suitable I would like to use two parts in a dual redundant
configuration with the outputs from one device connected to the outputs of the
other device. the grounds would be common but each device would be fed from
separate batteries.  Under normal conditions one device would be powered and
enabled, the other device would be powered and the outputs disabled.  What is
the reverse current leakage for the part if it is in shutdown but the output is
forced high by the other device?
Answer:  The reverse leakage should be in the order of 30-50nA under these
conditions but no higher than 12uA at elevated temperature.
5)Question: If only one device was powered would it back feed through the
unpowered device to it’s input? (i.e. body diode as in mosfet pass elements). 
Would the device be damaged if configured in this way?
Answer: ADP3302AR4/5 pass transistor is a bipolar not a mosfet.  With a bipolar
as a pass element, you have a back-to-back diodes so you wouldn’t concern about
a current path back to it input.
6)Question: If both parts were powered and both outputs enabled at the same
time, how would this affect current drain? and again what is the potential for
damaging the device in this condition.  Supply batteries will be 6V lithium
manganese 1300mAH, initial voltage can be as high as 7.2V.
Answer: As long as the input voltage is higher than the output voltage, it
would not affect the collect current nor damage the part under these
conditions.

  • adp3302
  • Share
  • History
  • More
  • Cancel
Comments
Anonymous
Related
 
社交网络
快速链接
  • 关于ADI
  • Partners
  • 模拟对话
  • 职业
  • 联系我们
  • 投资信息
  • 新闻中心
  • 质量和可靠性
  • 办事处与代理商
  • Analog Garage
语言
  • English
  • 简体中文
  • 日本語
  • Руccкий
电子快讯

欲获得最新ADI产品、设计工具、培训与活动的相关新闻与文章,请从我们的在线快讯中选出您感兴趣的产品类别,每月或每季度都会发送至您的收件箱。

订阅
Switch to mobile view
Analog Logo
© 1995 - 2022 Analog Devices, Inc. All Rights Reserved 沪ICP备09046653号-1
  • ©
  • 1995 - 2022 Analog Devices, Inc. All Rights Reserved
  • 沪ICP备09046653号-1
  • 网站地图
  • 隐私和保密政策
  • 隐私设置
  • 使用条款
 
Social
Quick Links
  • About ADI
  • Partners
  • Analog Dialogue
  • Careers
  • Contact us
  • Investor Relations
  • News Room
  • Quality & Reliability
  • Sales & Distribution
  • Analog Garage
Languages
  • English
  • 简体中文
  • 日本語
  • Руccкий
Newsletters

Interested in the latest news and articles about ADI products, design tools, training and events? Choose from one of our 12 newsletters that match your product area of interest, delivered monthly or quarterly to your inbox.

Sign Up
Switch to mobile view
Analog Logo
© 1995 - 2022 Analog Devices, Inc. All Rights Reserved 沪ICP备09046653号-1
  • ©
  • 1995 - 2022 Analog Devices, Inc. All Rights Reserved
  • 沪ICP备09046653号-1
  • Sitemap
  • Privacy & Security
  • Privacy Settings
  • Terms of use
EngineerZone Uses cookies to ensure you get the best experience in our community. For more information on cookies, please read our Privacy & Security Statement.