• State Not Answered
  • Replies 2 replies
  • Subscribers 40 subscribers
  • Views 180 views
  • Users 0 members are here
Options
Related 

        

            Post
             Go back to editing
        

    

    


    

    









		











	
	
			
	
			
		
	
	
		

		
CONFIGURING THE SETPOINT TEMPERATURE with ADN8835CP-EVALZ and ADN8835 BASE BOARD (ADN8834MB-EVALZ)

		
		

		

			

									
						PKP
					
							

			
				
									
											
			        
                                                			
				
			
		


				
		

		    
		    
		    		    
			
Hi,




I request you to provide me the instructions for the configuring of SETPOINT temperature and the RANGE with the above mentioned boards. Instructions were clear when using AND8831-EVALZ Board but here, no such support.


May I also know what the equation involving the Vtempset, the Thermistor resistance(Rth) and any other resistances(R2/W3 and others if any) is.  



Kindly help me out at the earliest.


Thank you!

										


				May I also know what the equation involving the Vtempset, the Thermistor resistance(Rth) and any other resistances(R2/W3 and others if any) is.

[edited by: PKP at 5:32 PM (GMT -5) on 13 Jan 2022]
				

					


				
				
		

			
						
									
									
						
						
			
			
			
			
		


					

			





	

		
	











	

	

					



			


				
	









	
    
	

  • 
	
    



	
		
	
	



    
	
    
		
    
							
					
    
		
    
			
													0
							
			
				
									
							
						
				
			
					
    
	
    

		
		
    
					
    Hi,
    

    I am moving this thread to Energy Monitoring and Metering - EngineerZone (analog.com) community to better assist you.
    

    Regards,
    

    Mae
    
			
    

		
		
		
		
	
    
	
    
		
    
			
		
    
	
    
	
    
		
						
						
				
						
				
				
		
		
    
			
		
    
	
    

    

    

    • 

	

  • 
	
    



	
		
	
	



    
	
    
		
    
							
					
    
		
    
			
													0
							
			
				
									
							
						
				
			
					
    
	
    

		
		
    
					
    Hi  ,
    

    

    Basically we have the same method in setting the set point using the ADN8835. The very important thing here is to take note of the plot of figure 39 in the datasheet.
    

     
    

      

    • The main goal here is for the TEC voltage should be at 0V (0A) when the setpoint is reached. Thus, the OUT2 voltage must be at 1.25V at setpoint.
      • 

    • So you can set IN2P (Vtempset at 1.25V) for example. Now you need to work on the thermistor amplifier (chopper1) circuitry.
      • 

    • You need to set first the following:
      Tlow = lower temp limit
      Tmid = center temp
      Thigh = high temp limit
      • 

    • you need to make the chopper 1, OUT1 behaves below:
       
      at Tlow, OUT1 ~0.3V
      Tmid ~1.25V
      Thigh ~2.2V
      In order to do that, refer to page 19 of datasheet.
      • 

    

    after setting that and achieve the figure 34, you can now set the Vtempset using the same curve.
    

    For any additional questions, reach me at noel.tenorio@analog.com

    regards,
    

    Noel
    
			
    

		
		
		
		
	
    
	
    
		
    
			
		
    
	
    
	
    
		
						
						
				
						
				
				
		
		
    
			
		
    
	
    

    

    

    •