Products Mentioned

ADP2442 Recommended for New Designs
The ADP2441 / ADP2442 is a constant frequency, current mode control, synchronous, step-down, dc-to-dc regulator that is capable of driving loads of up...
Datasheet
ADP2442 on Analog.com

  • State Verified Answer
  • Replies 5 replies
  • Subscribers 38 subscribers
  • Views 993 views
  • Users 0 members are here
Options
 

        

            Post
             Go back to editing
        

    

    


    

    









		


















	
	
			
	
			
		
	
	
		

		
ADP2442 shutdown output after some seconds



		

			

									
					    staticboards
					
							

			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Jan 30, 2018 
				
			
			
		
    

				
		
    
		    		    
		    
		    	
			
    Hi!
    
 
    We are evaluating the ADP2442 ic. Our prototype is a basic dc dc converter, from 24V to 5V
    
 
    This is the schematic (basically a copy&paste of the reference design):
    
 
    
 
    If we connect the pin 6 (SYNC/MODE) to gnd (pulse skip mode), the circuit seems to work. We have 5V and we can supply current for a test load.
    
 
    But if we use the fixed mode (pin 6 to vcc), the circuit works for a couple of seconds, and then, it shutdowns. We were looking for something strange, but at first, we dont see anything.
    
 
    any idea or suggestion?
    
 
    Thank you very much!!!
    
									
			        
		
    

				
						
        

    
    Tags: 
                                            
                 Internal Power Switch Buck Regulators
                
                                                    
                 adp2442
                
                                                    
                 power
                
                                                    
                 dcdc
                
                                                    
                 Step-Down (Buck) Regulators
                
                                
            
    
    
    

		
    
			
						
									
									
						
						
			
			
			
			
		
    

        
        

					
    
			
    


    
















    
	
    
	
    
					



			








	
	
	
	



Parents
	
      
	

    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
						
                            
            
            				
            
                on Feb 5, 2018 2:29 AM
            
            
					
      
	
      

		
		
      
					
      Hi,
      
 
      The schematic looks fine. For the layout, it seems that the AGND and PGND planes are not connected together on the PCB?
      
 
      When doing PCB layout, it is fine the separate AGND and PGND. But usually, we will connect these two ground planes on the PCB board.
      
 
      Another thing is, when setting to FPWM mode, how many load did you draw from Vout or even under no load condition, the ADP2442 will shut down after a while?
      
 
      Thanks!
      
			
      

		
			
	      

		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
				
						
				
				
		
		
      
			
		
      
	
      

      

      • 

	
    



Reply

      


    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
						
                            
            
            				
            
                on Feb 5, 2018 2:29 AM
            
            
					
      
	
      

		
		
      
					
      Hi,
      
 
      The schematic looks fine. For the layout, it seems that the AGND and PGND planes are not connected together on the PCB?
      
 
      When doing PCB layout, it is fine the separate AGND and PGND. But usually, we will connect these two ground planes on the PCB board.
      
 
      Another thing is, when setting to FPWM mode, how many load did you draw from Vout or even under no load condition, the ADP2442 will shut down after a while?
      
 
      Thanks!
      
			
      

		
			
	      

		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
				
						
				
				
		
		
      
			
		
      
	
      

      

      • 


    


Children
	
    No Data