The Engineering Mind
3D ToF Depth Sensing
Aerospace and Defense (ADEF) System Platforms
Analysis Control Evaluation (ACE) Software
Clock and Timing
Design Tools and Calculators
Direct Digital Synthesis (DDS)
Embedded Vision Sensing
Energy Monitoring and Metering
FPGA Reference Designs
Interface and Isolation
Low Power RF Transceivers
MEMS Inertial Sensors
Motor Control Hardware Platforms
Power By Linear
Precision Technology Signal Chains
Processors and DSP
RF and Microwave
Signal Chain Power (SCP)
Speech Processing Solutions
Wide Band RF Transceivers
Wireless Sensor Networks Reference Library
Other Products requires membership for participation - click to join
3B01: the connection between the 26-pin and 16 channel.
442 - I cannot find the datasheet for the 442 (old OPAMP Module)
751: old datasheet
Ac coupling Vs Dc coupling
AC1307E Power Supply input range
AD-MSDPD-EVB: Eval Board Datasheet
AD10200: Are the two channels fully independent?
AD10200: Channel-to-Channel isolation test with AINA2 and AINB2
AD8436 - Down conversion to 100 uV
AD8436 - Power consumption for added amplifiers
AD8436 - Power supply
AD8436 - What is unique about this device?
AD8436: output buffer with higher gain than unity
AD8436: single supply or dual supply
ADATE304 Force Voltage
ADATE318: What supply voltage do I use for VDD_THERM?
ADMP441 output format
ADN2531: Can output be configured as current source?
ADN2685: could you send the final datasheet?
ADN2814: power consumption at 10MHz
ADN2814: Recover a 1T clock from a EFM signal
ADN2816 Evaluation Board Documentation
ADN2816: Which clock edge does the retiming block of the ADN2816 use to output data?
ADN2817 error correction
ADN2820: Optical fiber communication
ADN2830 MPD current
ADN2830: Monitor photodiode
ADN2830: CW laser diode power control
ADN2871: Differential drive circuit for driving a VCSEL Laser diode.
ADN2872: Is it possible to use 2 laser drivers in parallel to have the modulation current of 130 mA?
ADN2873: Minimum differential signal between the DATAP and DATAN
ADN2880: MAX leakage current specification of ADN2880 input
ADN2882 Evaluation Board
ADN2890/1/2 at 100Mbps?
ADN4600 Junction Temperature
ADN4600 thermal characteristics
ADN4600: Reset Power on timing
ADN469xE Evaluation Board
ADN469xE IBIS Models
ADN469xE: MLVDS and how is it different from B-LVDS and RS-485?
ADN469xE: Rise and Fall Time matching Data Rate
ADN8831 and operate DVDD with < 3v
ADN8831: Driving a 12V external TEC module
ADN8831: How to drive a 12V TEC?
ADN8831: how to drive an APD
ADN8831: PWM duty cycle
ADN8834: Evaluation board difference
Aqueous washing of ADI parts?
availability of the ADMC300 devices
Baking BGA in Tray or trays
Baking of parts in a Reel
Can ADN4604 do single ended 75Ohm input and output?
Can I connect one input to multiple outputs?
datasheet 940, 941, 942, 943, 944, 945
Digital programmable power with 1.8V logic to Vout = 5V
Does changing the crosspoint connectivity affect the state of previously configured connections?
doubling ADN8810 Iout configuration query (SR#: 1202803)
EVAL-AD8436 evaluation board operation with single supply
Evaluation Boards for the ADN2531
Failure probability for AD8468
How can I order Linear Circuit Design Handbook?
Maximum Recommended PMU Load Capacitance
Package general: What is the pin pitch of LFCSP package?
Package: 10 ld Ceramic Flat Package footprints
paste mask recommendation
PFC controller + LED driver in one package
Replacement for PMI119-883
RoHS compliant status E
RTI-850 RTI products
Shelf life for Analog parts
Shelf life of drypack used to ship Moisture/Reflow Sensitive Surface Mount Devices
Support for Mobile TV tuner parts: ADMTVxxx / IDTxxxx
Technical questions ADN8831
The unit of MTTF data on ADI web site
transistor counts for a processor to calculate the MTBF
unused inputs or outputs?
What data rates or range of data rates are supported?
What data rates protocols are supported?
Where can I find e-book versions on your seminar books to download?
Where can I find the user guide for the ADN2871/ADN2873 evaluation boards?
which register we can read to know the status of HD
Why the Analog Input Current from ?10mA to 10 mA was limited.
there was something wrong with the ALS pin in the Fig 30 of the datasheet.
ALS should connect to GND so that bias and modulation current will not be turn
Privacy & Security Statement
Accept & Continue