HIGH LIMIT 1 (PAGE 0x05) Registers Settings

Hi junboyi@bluedanube.com ,

thank you for your question, please refer to the AD7293 datasheet (DS), "Internal Channel Monitoring" section, which describes scaling of each of the mentioned channels. (Fugure 42. attached for your convenience, which reflects the same, more detaild description is in DS.) Resulting codes are then compared to determine, if ALERT will be triggered based on the configured limit. 

Regards,

Arnost

Hi junboyi@bluedanube.com ,

thank you for your question, please refer to the AD7293 datasheet (DS), "Internal Channel Monitoring" section, which describes scaling of each of the mentioned channels. (Fugure 42. attached for your convenience, which reflects the same, more detaild description is in DS.) Resulting codes are then compared to determine, if ALERT will be triggered based on the configured limit. 

Regards,

Arnost

If I need to figure out how to map the input to Limit Register ADC data, then I don't need to ask questions here.

As user, I would like to have a simple, direct conversion between input voltage range to Mux range, especially for those with negative voltage range.

Thanks.

JYI

Hi junboyi@bluedanube.com, 

based on the input values indicated above, it is direct conversion using 12bit resolution. For example BI-Vout0MON have range -5V to 5V, this is scaled to 12bit resolution where -5V corresponds to 0x000 and 5V 0xFFF (as described in DS INTERNAL CHANNEL MONITORING section). 

Conversion for BI-Vout0MON can be done using this formula: LIMIT_CODE = ((Desired_Voltage_Limit+5)/10)*2^(12)) 

Here is described reasoning behind it: 

Similar approach needs to be taken for other inputs, here is direct equation examples:

RS0+MON:  LIMIT_CODE = ((Desired_Voltage_Limit)/62.5)*2^(12))

DACVDD-BI:  LIMIT_CODE = ((Desired_Voltage_Limit)/6.25)*2^(12))

DACVDD-UNI:  LIMIT_CODE = ((Desired_Voltage_Limit)/25)*2^(12))

AVSS:   LIMIT_CODE = ((Desired_Voltage_Limit+7.5)/10)*2^(12)) 

AVDD: LIMIT_CODE = ((Desired_Voltage_Limit)/6.25)*2^(12))

Regards,

Arnost

Very Usefully.

Thanks.

JYI

The section INTERNAL CHANNEL MONITORING of DS indicates there is a divider factor for each channel, such as for BI-Vout Mon, it says

For BI-VOUTxMON, divide by 8 and level shift within a −5 V to +5 V range, where 0x000
equates to approximately −5 V, and 0xFFF equates to approx-imately +5 V.

I wonder the above mapping formulas is including this divider factor or not.

For my understanding, the formulars is just for level shift, not including the input divider factor, right?

Thanks.

JYI

Hi junboyi@bluedanube.com ,

formulas indicated above shows conversion between input voltage and ADC code.

Scaling is happening internally on chip, and it is described in the datasheet mainly to give understanding concerning the input ranges, once input ranges are involved in the formula correctly it should account correctly for scaling and give you correct CODE output.

Input voltages are scaled to the value of 1.25V to be process by internal ADC, which have 1.25V voltage reference. 

I hope this helps to clarify you this topic. 

Regards,

Arnost

Thanks.

JYI

Is reset default setting for OFFSET 1 register good enough to use Internal Monitoring Functions or need to be setup for each monitoring channel?

Thanks.

JYI

Hi junboyi@bluedanube.com ,

OFFSET registers allows to eliminate unwanted the offset in your system. To determine, how precise internal measurement you need is dependent on your requirement and purpose of the internal monitors. Offset registers allows to adjust output value by range of 7 bits up and down (+128/-128 codes) out of 12bit resolution (4096 codes), which equals ~1/32 of full range. 

Out of the "box" accuracy of the AD7293 can be found the datasheet, in specification section (Table1).

Regards,

Arnost

Thanks.

I was confused with OFFSET-0 for DAC channel which needs to set offset for the output range.

JYI

The DS says AVSS maximum range -7V to +0.3V and BI-Vout is  AVss-0.3V to DACVdd-BI+0.3V.

Does the AD7293 be working when AVSS is less -5V, say -6.5V and have BI-Vout to be less than -5V, say -5.5 to -6V?  

Thanks.

JYI