• State Verified Answer
  • Replies 4 replies
  • Subscribers 7 subscribers
  • Views 793 views
  • Users 0 members are here
Options
Related 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
ADPD4100 Peak Sampling Rate



		

			

									
					    tylerchen
					
							

			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Jul 16, 2021 
				
			
			
		
    

				
		
    
		    		    
		    
		    	
			
    Hello ADI support team! Quick question for you -
    

    I'm trying to get a ballpark for how many samples per second this AFE can achieve across all channels, though I know the slot timing configuration registers depend on the number of repeats, pre-width, offset, etc. In the ADPD4100 datasheet I see that the peak sampling rate is listed as 9kHz when using the internal 1Mhz low-freq oscillator (pg 1). 
    

    Where does the 9kHz number come from? Is this 9kHz times 12 timeslots = 108k samples / sec?
    

    Thanks very much for your support!
    

    Best,
    

    Tyler
    
								
    

				
				
		
    
			
						
									
									
						
						
			
			
			
			
		
    

        
        

					
    
			
    


    


	















    
	
    
	
    
					



			








	
	
	
	



Parents
	
      
	

    • 
	
      



	
			
		
	



      
	
      
		
      
							
					
      
		
      
			
													+1
							
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
			                            
                        
                on Jul 16, 2021 7:39 PM
            
            
					
      
	
      

		
		
      
					
      Hi Tyler,
      

      The 9 kHz sampling rate is based on our test of the ADPD4100 part. Technically, you can get 108k sps if the time for each slot is very minimal. 
      

      The ADPD4100 sampling rate can further be increased by turning off the sleep cycle. 
      

      We are in the process to implement firmware for the impulse response mode which allows to acquire limited number of samples but at 500k sampling rate.
      

      Regards,
      

      Glen B.
      
			
      

		
		
		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
				
						
						
				
				
		
		
      
			
		
      
	
      

      

      • 

	
    



Reply

      


    • 
	
      



	
			
		
	



      
	
      
		
      
							
					
      
		
      
			
													+1
							
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
			                            
                        
                on Jul 16, 2021 7:39 PM
            
            
					
      
	
      

		
		
      
					
      Hi Tyler,
      

      The 9 kHz sampling rate is based on our test of the ADPD4100 part. Technically, you can get 108k sps if the time for each slot is very minimal. 
      

      The ADPD4100 sampling rate can further be increased by turning off the sleep cycle. 
      

      We are in the process to implement firmware for the impulse response mode which allows to acquire limited number of samples but at 500k sampling rate.
      

      Regards,
      

      Glen B.
      
			
      

		
		
		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
				
						
						
				
				
		
		
      
			
		
      
	
      

      

      • 


    


Children