• State Not Answered
  • Replies 1 reply
  • Subscribers 5 subscribers
  • Views 372 views
  • Users 0 members are here
Options
Related 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
Noise and baseline problem in "EVAL BOARD ADPD105" . How to fix this issue?



		

			

									
					    AKUMAR1771
					
							

			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Sep 16, 2020 
				
			
			
		
    

				
		
    
		    		    
		    
		    	
			
    Sir,
    

    I am working on ADPD105 EVALUATION board and trying to run the module using ADPD105 openmarket wavetool utility. The issue with this is the noise presence in the PPG waveform. I would also like to mention that I am driving two LED's, one in each time slot. So please look into the issue and suggest some solution.
    

      
    
								
    

				
				
		
    
			
						
									
									
						
						
			
			
			
			
		
    

        
        

					
    
			
    


    


	
    
		
	
    















    
	
    
	
    
					



			








	
	
	
	



Parents
	
      
	

    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
			                            
                        
                on Sep 22, 2020 4:09 AM
            
            
					
      
	
      

		
		
      
					
      Hi,
      

      

      That part is old. We recommend ADPD1080 or ADPD4100. ADPD1080 is our cost efficient solution and ADPD4100 is our higher end, high SNR, power efficient solution. Also, if you require 90+ dB DC SNR, you have to use ADPD4100.
      

      May I ask why you’re using such long LED pulses? Ideally, you should not use the settings you’re currently using. For the best PPG performance, please stick to the recommendations on Page 26 of the datasheet and the Table 18 on that page. Using longer LED pulses makes the system prone to ambient light issue, the main aspect of this IC is to use shorter pulses to suppress/reject ambient light. Also, you need to check whether you set all the other settings right. Especially TIA BIAS voltage and cathode voltage could be critical in reducing noise. It could be a linear dynamic range issue here as well. You need to check whether you are in safe, linear region. When you reduce the LED currents, what do you see?
      

       
      

      Best regards,
      

      Yigit
      
			
      

		
		
		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
				
						
				
				
		
		
      
			
		
      
	
      

      

      • 

	
    



Reply

      


    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
			                            
                        
                on Sep 22, 2020 4:09 AM
            
            
					
      
	
      

		
		
      
					
      Hi,
      

      

      That part is old. We recommend ADPD1080 or ADPD4100. ADPD1080 is our cost efficient solution and ADPD4100 is our higher end, high SNR, power efficient solution. Also, if you require 90+ dB DC SNR, you have to use ADPD4100.
      

      May I ask why you’re using such long LED pulses? Ideally, you should not use the settings you’re currently using. For the best PPG performance, please stick to the recommendations on Page 26 of the datasheet and the Table 18 on that page. Using longer LED pulses makes the system prone to ambient light issue, the main aspect of this IC is to use shorter pulses to suppress/reject ambient light. Also, you need to check whether you set all the other settings right. Especially TIA BIAS voltage and cathode voltage could be critical in reducing noise. It could be a linear dynamic range issue here as well. You need to check whether you are in safe, linear region. When you reduce the LED currents, what do you see?
      

       
      

      Best regards,
      

      Yigit
      
			
      

		
		
		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
				
						
				
				
		
		
      
			
		
      
	
      

      

      • 


    


Children
	
    No Data