Hello, I have an EVAL-ADICUP3029 and I am trying to use the CrossCore Serial Programmer to erase, but I get a "No autobaud response" error. I was following these instructions: https://wiki.analog.com/resources/eval/user-guides/eval-adicup3029/tools/ccsfp_unlock_adicup3029 S2 UART switch is set to USB Power switch is set to USB I press and hold "S3 boot", then press and release "S1 Reset", then hit start in the CrossCore Serial Programmer The board is fresh out of the box. Windows drivers install normally and the Daplink drive shows up if this is relevant. Here are my CrossCore Serial Programmer settings, is there anything I'm doing wrong?

Products Mentioned

ADuCM3029 Recommended for New Designs
The ADuCM3027/ADuCM3029 microcontroller units (MCUs) are ultra low power microcontroller systems with integrated power management for processing, control...
Datasheet
ADuCM3029 on Analog.com

Thread Details

State Not Answered
Replies 12 replies
Subscribers 7 subscribers
Views 1200 views
Users 0 members are here

ADICUP3029 No autobaud response

JensL

on Oct 30, 2024

Category: Software

Product Number: ADuCM3029

Hello,

I have an EVAL-ADICUP3029 and I am trying to use the CrossCore Serial Programmer to erase, but I get a "No autobaud response" error.

I was following these instructions: https://wiki.analog.com/resources/eval/user-guides/eval-adicup3029/tools/ccsfp_unlock_adicup3029

S2 UART switch is set to USB
Power switch is set to USB
I press and hold "S3 boot", then press and release "S1 Reset", then hit start in the CrossCore Serial Programmer

The board is fresh out of the box. Windows drivers install normally and the Daplink drive shows up if this is relevant.

Here are my CrossCore Serial Programmer settings, is there anything I'm doing wrong?

Edit Notes

Corrected the button sequence, but the result is identical.
[edited by: JensL at 7:48 PM (GMT -5) on 7 Nov 2024]

software microcontrollers adicup3029 CrossCore Serial Programmer Precision Microcontrollers aducm3029 Show More

Parents

Akila

on Nov 6, 2024 3:21 AM
0
Hi,

The comport, if detected, shows COMx (mbed serial port), not as (USB Serial Device).
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
JensL
on Nov 6, 2024 4:07 AM in reply to Akila
0
Hi Akila

Thank you for your reply. Do you happen to know which driver I need for Windows 10? There is a deprecated Mbed driver for Windows 7, but there seems to be no Windows 10 driver for manual installation. Source: https://os.mbed.com/docs/mbed-os/v6.16/program-setup/windows-serial-driver.html
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
JensL
on Nov 7, 2024 2:46 PM in reply to JensL
0
Update: I installed the old Windows 7 Mbed driver. The port now shows as "mbed serial port", but the "No autobaud response" error remains.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
Akila

on Nov 7, 2024 4:49 PM in reply to JensL
0
Hi,

Could you confirm by removing and plugging the board back that this comport corresponds to EVAL-ADICUP3029 board that is connected?
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
JensL
on Nov 8, 2024 7:25 AM in reply to Akila
0
Hello

Yes, I can confirm. When I unplug the board, the port disappears and reappears after plugging it back in. The error remains.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
Akila

on Nov 11, 2024 2:03 AM in reply to JensL
0
Hi,

Usually when the board gets plugged, driver gets installed automatically.

Kindly download and install Windows 10 serial driver from internet.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
Samuele
on Nov 18, 2024 5:01 AM in reply to Akila
0
I've the same problem as JensL. I have the mbed serial driver installed. Can you help me?
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
JensL
on Nov 18, 2024 4:03 PM in reply to Akila
0
Hi again

Here is an update and summary. So far I have tried:

Windows 10 Pro with the automatically installed driver (driver version 10.0.19041.3636)

Windows 10 Pro with the Windows 7 driver 16466, this is the last releasted mBed driver for manual installation

Windows 7 Pro VM with the Windows 7 driver 16466

All of the above result in the same "No autobaud response" error. Please mind that there is no mBed Windows 10 driver except for the automatically installed one.

I'm looking forward to any lead to solve this issue.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
Samuele
on Nov 19, 2024 10:07 AM in reply to JensL
0
Hi JensL,

I tried to run the blink_example in Debug mode using the CrossCore Embedded Studio. I still didn't resolve the issue because I had to deal with some other errors. It seems that the aducm3029 MCU is not working at all.

Maybe, you can also try to program it using CrossCore. It might works for you.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel

Reply

Samuele
on Nov 19, 2024 10:07 AM in reply to JensL
0
Hi JensL,

I tried to run the blink_example in Debug mode using the CrossCore Embedded Studio. I still didn't resolve the issue because I had to deal with some other errors. It seems that the aducm3029 MCU is not working at all.

Maybe, you can also try to program it using CrossCore. It might works for you.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel

Children

No Data

Popular Forums

Product Forums

Application Forums

Design Center Forums

Highlighted Webinar

Places

Libraries

Latest Webinars

Challenge Yourself!

What's Brewing

Places

Resources

Highlighted Blogs

Latest Blogs

ADI Blogs

Visit ContentZone

Featured Content

View Content By Industry

View Content By Technology

Products Mentioned

Thread Details

ADICUP3029 No autobaud response

Edit Notes