Hello, I have an EVAL-ADICUP3029 and I am trying to use the CrossCore Serial Programmer to erase, but I get a "No autobaud response" error. I was following these instructions: https://wiki.analog.com/resources/eval/user-guides/eval-adicup3029/tools/ccsfp_unlock_adicup3029 S2 UART switch is set to USB Power switch is set to USB I press and hold "S3 boot", then press and release "S1 Reset", then hit start in the CrossCore Serial Programmer The board is fresh out of the box. Windows drivers install normally and the Daplink drive shows up if this is relevant. Here are my CrossCore Serial Programmer settings, is there anything I'm doing wrong?

Products Mentioned

ADuCM3029 Recommended for New Designs
The ADuCM3027/ADuCM3029 microcontroller units (MCUs) are ultra low power microcontroller systems with integrated power management for processing, control...
Datasheet
ADuCM3029 on Analog.com

ADICUP3029 No autobaud response

JensL

on Oct 30, 2024

Category: Software

Product Number: ADuCM3029

Hello,

I have an EVAL-ADICUP3029 and I am trying to use the CrossCore Serial Programmer to erase, but I get a "No autobaud response" error.

I was following these instructions: https://wiki.analog.com/resources/eval/user-guides/eval-adicup3029/tools/ccsfp_unlock_adicup3029

S2 UART switch is set to USB
Power switch is set to USB
I press and hold "S3 boot", then press and release "S1 Reset", then hit start in the CrossCore Serial Programmer

The board is fresh out of the box. Windows drivers install normally and the Daplink drive shows up if this is relevant.

Here are my CrossCore Serial Programmer settings, is there anything I'm doing wrong?

Corrected the button sequence, but the result is identical.
[edited by: JensL at 7:48 PM (GMT -5) on 7 Nov 2024]

Tags: software microcontrollers adicup3029 CrossCore Serial Programmer Precision Microcontrollers aducm3029 Show More

0 nikolas90
on Oct 31, 2024 4:55 PM
Hello, I also have the same problem.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
0 Akila

on Nov 6, 2024 3:21 AM
Hi,

The comport, if detected, shows COMx (mbed serial port), not as (USB Serial Device).
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
0 JensL
on Nov 6, 2024 4:07 AM in reply to Akila
Hi Akila

Thank you for your reply. Do you happen to know which driver I need for Windows 10? There is a deprecated Mbed driver for Windows 7, but there seems to be no Windows 10 driver for manual installation. Source: https://os.mbed.com/docs/mbed-os/v6.16/program-setup/windows-serial-driver.html
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
0 JensL
on Nov 7, 2024 2:46 PM in reply to JensL
Update: I installed the old Windows 7 Mbed driver. The port now shows as "mbed serial port", but the "No autobaud response" error remains.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
0 Akila

on Nov 7, 2024 4:49 PM in reply to JensL
Hi,

Could you confirm by removing and plugging the board back that this comport corresponds to EVAL-ADICUP3029 board that is connected?
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
0 JensL
on Nov 8, 2024 7:25 AM in reply to Akila
Hello

Yes, I can confirm. When I unplug the board, the port disappears and reappears after plugging it back in. The error remains.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
0 Akila

on Nov 11, 2024 2:03 AM in reply to JensL
Hi,

Usually when the board gets plugged, driver gets installed automatically.

Kindly download and install Windows 10 serial driver from internet.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
0 Samuele
on Nov 18, 2024 5:01 AM in reply to Akila
I've the same problem as JensL. I have the mbed serial driver installed. Can you help me?
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
0 JensL
on Nov 18, 2024 4:03 PM in reply to Akila
Hi again

Here is an update and summary. So far I have tried:

Windows 10 Pro with the automatically installed driver (driver version 10.0.19041.3636)

Windows 10 Pro with the Windows 7 driver 16466, this is the last releasted mBed driver for manual installation

Windows 7 Pro VM with the Windows 7 driver 16466

All of the above result in the same "No autobaud response" error. Please mind that there is no mBed Windows 10 driver except for the automatically installed one.

I'm looking forward to any lead to solve this issue.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel
0 Samuele
on Nov 19, 2024 10:07 AM in reply to JensL
Hi JensL,

I tried to run the blink_example in Debug mode using the CrossCore Embedded Studio. I still didn't resolve the issue because I had to deal with some other errors. It seems that the aducm3029 MCU is not working at all.

Maybe, you can also try to program it using CrossCore. It might works for you.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel

Partner Forums

Partner Libraries

Products Mentioned

ADICUP3029 No autobaud response