Unable to build no-OS on windows

That's really strange. Can you please clean your project and eventually create a new one based on the latest discussions?

Also, I don't think you need Communication.c and Communication.h files, nor axi_io.c, axi_io.h.

If you use ZC706, you don't need `altera` drivers.

Just use main file `fmcdaq2.c`, `config.h` from `fmcdaq2` folder, drivers (ad9144.c ad9144.h, ad9523.c, ad9523.h ad9680.c, ad9680.h) and the drivers from `common_drivers`(platform_drivers + axi drivers - adc_core, dac_core, etc).

I suggest adding first the fmcdaq2.c + config file and based on the required includes add step by step the files from the 2019_r1 release branch.

Regards,

Antoniu

Hi,

I tried doing it.I ended up with errors  which were like multiple declaration of xilinx_xcvr_drp_read, etc with which I had to comment some of the loops in xcvr_core.c, xilinx_transceiver.c, etc.

I could program the fpga and run the configuration, I get an output as shown below on the SDK terminal.

Available sampling rates:
    1 - ADC 1000 MSPS; DAC 1000 MSPS
    2 - ADC  500 MSPS; DAC 1000 MSPS
    3 - ADC  500 MSPS; DAC  500 MSPS
    4 - ADC  600 MSPS; DAC  600 MSPS
    5 - ADC 1000 MSPS; DAC 2000 MSPS (2x interpolation)
choose an option [default 1]:
2 - ADC  500 MSPS; DAC 1000 MSPS

QPLL ENABLE

CPLL ENABLE
xcvr_setup: Failed to set line rate!Desired rate: 5000000, obtained rate: 0
Tx link is enabled
Measured Link Clock: 250 MHz
Link status: DATA
SYSREF captured: Yes
Rx link is enabled
Measured Link Clock: 250 MHz
Link status: CGS
SYSREF captured: Yes
adc_setup adc core initialized (1000 MHz).

Whereas, I am unable to view the sine wave on the oscilloscope.Could you please tell how am I suppose to view the sine wave as I want to know if I have followed the right procedure?

Thank you & regards

Hello,

You should not get any errors like multiple declarations of specific function (and you should not comment code blocks in the drivers implementations(. Can you please share the entire src folder that you are using?

Also, it seems that the phy layer is failing (xcvr_setup).

Regards,

Antoniu

Hi

Yes, please find the attachment. Can I please know how do I attach the folder? I only have the provision of file upload.

The error it shows is in the axi_adxcvr.c, xilinx_transceiver.c, xilinx_xcvr_channel.c, etc files.

Can you please tell how do I resolve these errors?

Thank you & regards,

Please remove axi_adxcvr.c axi_adxcvr.h, delay.h and error.h

And make sure you haven't done any other modifications to the implemented functions (like commenting loops, etc.)

Regards,

Antoniu

Hello,

I am coming with an update: you can use now the project version available with https://github.com/analogdevicesinc/no-OS/pull/500

It should work with ZC706

All the source files you need are specified in README found in the projects folder.

Looking forward to your feedback,

Antoniu

Hi,

Based on your last reply, I removed the axi_adxcvr.c axi_adxcvr.h, delay.h and error.h files and the project was built successfully. I programmed ZC706 and when I launch on the debugger, I get this output on the putty as follows.

Available sampling rates:
        1 - ADC 1000 MSPS; DAC 1000 MSPS
        2 - ADC  500 MSPS; DAC 1000 MSPS
        3 - ADC  500 MSPS; DAC  500 MSPS
        4 - ADC  600 MSPS; DAC  600 MSPS
        5 - ADC 1000 MSPS; DAC 2000 MSPS (2x interpolation)
choose an option [default 1]:
2 - ADC  500 MSPS; DAC 1000 MSPS

QPLL ENABLE

CPLL ENABLE
Tx link is enabled
                  Measured Link Clock: 250 MHz
                                              Link status: DATA
                                                               SYSREF captured: Yes
   Rx link is enabled
                     Measured Link Clock: 125 MHz
                                                 Link status: DATA
                                                                  SYSREF captured: Yes
      adc_setup adc core initialized (500 MHz).

I am unable to see the output sine waveform on the oscilloscope. How am I suppose to do that? Is there anything which I am missing?

Thank you & regards

I dont get the dac_setup dac core intialized displayed on the putty. I do not know the reason whereas the dac_core is already in the src folder.

Hi amiclaus,

Can I please know where can I get the information of the code in order to understand the entire project properly.

Thank you & regards

If you are using the old implementation from https://github.com/analogdevicesinc/no-OS/blob/069c628ede138d340e5e129746e4fc608953ff49/common_drivers/dac_core/dac_core.c#L52

please remove the 0x4000 offset.

Same for https://github.com/analogdevicesinc/no-OS/blob/069c628ede138d340e5e129746e4fc608953ff49/common_drivers/dac_core/dac_core.c#L71

This should work.

Regards,

Antoniu