• State Verified Answer
  • +1 person also asked this people also asked this
  • Replies 3 replies
  • Subscribers 31 subscribers
  • Views 347 views
  • Users 0 members are here
Options
Related 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
ADM3058EBRIZ isolated CAN transceiver- I do not need the isolation



		

			

									
					    Shiladitya
					
							

			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Mar 25, 2021 
				
			
			
		
    

				
		
    
		    		    
		    
		    	
			
    Hi
    

    The ADM3058BRIZ is an isolated CAN transceiver and recommends a digital side GND1 and an analog side GND2
    

     If I do not have a requirement to isolate the bus, can I short GND1 and GND2 on my board and supply VDD2 with 5V and VDDD1 with both referenced to the common ground? Will this cause any performance issues or functional issues with this device? I intend to connect the line side of this transceiver on my board to a CAN test equipment such as Vector CAN analyser and never to an actual automotive CAN bus.
    

    I had to select this transceiver as I need a non-isolated CAN FD bus running at 12Mbps and I couldn't find any transceiver other than this family which met the data rate requirement.
    

    

    Thanks
    

    Shiladitya
    
								
    

				
				
		
    
			
						
									
									
						
						
			
			
			
			
		
    

        
        

					
    
			
    


    


	















    
	
    
	
    
					



			








	
	
	
	



Parents
	



Reply



Children
	
      
	

    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
        
            
			                            
                        
                on Mar 29, 2021 4:14 PM
            
            
												
						in reply to jnaso
					
									
        
	
        

		
		
        
					
        Thank you Jason. I know this is not ideally how I should be using an isolated transciever but i did not find any other transceiver which is non-isolated and supports CAN FD data rate of 12Mbps.
        

        If you have any suggestions, really appreciate it!
        

        

        Regards
        

        Shiladitya
        
			
        

		
		
		
		
	
        
	
        
		
        
			
		
        
	
        
	
        
		
						
						
				
						
				
				
		
		
        
			
		
        
	
        

        

        • 

	

      • 
	
        



	
		
	
	



        
	
        
		
        
							
					
        
		
        
			
													0
							
			
				
									
							        
			
			
			
        •  Analog Employees  
        
            
			                            
                        
                on Mar 29, 2021 5:05 PM
            
            
												
						in reply to Shiladitya
					
									
        
	
        

		
		
        
					
        Hi Shiladitya, 
        

        The ADM3050E/55E/56E/57E/58E all use the same transceiver. Any of those products could be options when only data rate is important. They are the only transceivers on the market that support >8Mbps that I am aware of. ADI doesn't have non-isolated models in the family though. 
        

        Btw, this is off datasheet, so the specification is not guaranteed... but the transceivers can be pushed up to ~15mbps before the bit symmetry gets poor. If this is a test bench rather than a product, it may be interesting to experiment with the higher data rates. 
        

        Regards,
        Jason
        
			
        

		
		
		
		
	
        
	
        
		
        
			
		
        
	
        
	
        
		
						
						
				
						
				
				
		
		
        
			
		
        
	
        

        

        •