Products Mentioned

AD9371 Recommended for New Designs
The AD9371 is a highly integrated, wideband RF transceiver offering dual channel transmitters and receivers, integrated synthesizers, and digital signal...
Datasheet
AD9371 on Analog.com

  • State Verified Answer
  • Replies 10 replies
  • Subscribers 107 subscribers
  • Views 611 views
  • Users 0 members are here
Options
Related 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
can not update iio with zc706+adrv9371



		

			

									
					    mashimaro
					
							

			
				
									
											
			
			
				
  •  Analog Employees  

			
			
			    	
			                    
                
				                on May 25, 2023 
				
			
			
		


				
		

		    		    
		    
		    		      		            		        
Category: Software

    		        		            		    
Product Number:  ad9371, zc706 

    		        		    		    	
			
Hi team,


I try to configure SD card for adrv9371-w/pcbz and zc706 platform. The problem is no IIO GUI showed on the monitor.


I followed the steps from wiki to configure sd-cardhttps://wiki.analog.com/resources/tools-software/linux-software/kuiper-linux.


After I wrote the image file to sd-card, I copied three documents below to BOOT partition.


    

  1. Zynq-zc706-adv7511-adrv937x/BOOT.BIN
    2. 

  2. Zynq-zc706-adv7511-adrv937x/devicetree/dtb
    3. 

  3. Zynq-common/ulmage
    4. 



Then I setup the physical system. The hdmi monitor could not show IIO gui.


How do I solve this problem?

									
			        
		


				
						
        

    
Tags: 
                                            
                 software
                
                                                    
                 ad9371
                
                                                    
                 zc706
                
                                                    
                 Wideband Transceiver IC
                
                                                    
                 RF Integrated Transceivers
                
                                
            

    
    

		

			
						
									
									
						
						
			
			
			
			
		


        
        

					

			





















	

	

					



			








	
	
	
	



Parents
	
    
	

  • 
	
    



	
		
	
	



    
	
    
		
    
							
					
    
		
    
			
													0
							
			
				
									
							        
			
			
			
    •  Analog Employees  
    •  Super User  
    
            
						
                            
            
            				
            
                on May 30, 2023 4:12 AM
            
            
					
    
	
    

		
		
    
					
    mashimaro said:
    But the whole system still didn't work.
    

    I am confused now. Something's missing from what you're telling me.
    

    Previously you said that the Kuiper boots and you can't open IIO GUI in Kuiper. But, you said the done led is not powered on.
    The done led is powered on when the FPGA is programmed, so you can't enter the GUI of the Kuiper unless everything is ok. 
    

    iulia said:
    Did you try opening a terminal in Kuiper and writing sudo osc to open IIO Oscilloscope? The password for the user <analog> is again <analog>.
    

      

    1. Did you try what I mentioned above?
      2. 

    2. Send me a picture of the screen with the Kuiper that boots, where you can't open the IIO GUI
      3. 

    3. Can you try with another ZC706?
      4. 

    4. If it still doesn't work, rewrite the SD card with the ADI Kuiper and make sure you put the following files in the BOOT partition:

        

      1. zynq-zc706-adv7511-adrv937x/zynq-zc706-adv7511-adrv9371/devicetree.dtb
        2. 

      2. zynq-zc706-adv7511-adrv937x/BOOT.BIN
        3. 

      3. zynq-common/uImage
        4. 

      

      5. 

    

    What application are you using for UART communication? I used TeraTerm and tried with Putty too.
    

     
    
			
    

		
			
	      

		
		
	
    
	
    
		
    
			
		
    
	
    
	
    
		
						
						
				
						
				
				
		
		
    
			
		
    
	
    

    

    • 

	




Reply

    


  • 
	
    



	
		
	
	



    
	
    
		
    
							
					
    
		
    
			
													0
							
			
				
									
							        
			
			
			
    •  Analog Employees  
    •  Super User  
    
            
						
                            
            
            				
            
                on May 30, 2023 4:12 AM
            
            
					
    
	
    

		
		
    
					
    mashimaro said:
    But the whole system still didn't work.
    

    I am confused now. Something's missing from what you're telling me.
    

    Previously you said that the Kuiper boots and you can't open IIO GUI in Kuiper. But, you said the done led is not powered on.
    The done led is powered on when the FPGA is programmed, so you can't enter the GUI of the Kuiper unless everything is ok. 
    

    iulia said:
    Did you try opening a terminal in Kuiper and writing sudo osc to open IIO Oscilloscope? The password for the user <analog> is again <analog>.
    

      

    1. Did you try what I mentioned above?
      2. 

    2. Send me a picture of the screen with the Kuiper that boots, where you can't open the IIO GUI
      3. 

    3. Can you try with another ZC706?
      4. 

    4. If it still doesn't work, rewrite the SD card with the ADI Kuiper and make sure you put the following files in the BOOT partition:

        

      1. zynq-zc706-adv7511-adrv937x/zynq-zc706-adv7511-adrv9371/devicetree.dtb
        2. 

      2. zynq-zc706-adv7511-adrv937x/BOOT.BIN
        3. 

      3. zynq-common/uImage
        4. 

      

      5. 

    

    What application are you using for UART communication? I used TeraTerm and tried with Putty too.
    

     
    
			
    

		
			
	      

		
		
	
    
	
    
		
    
			
		
    
	
    
	
    
		
						
						
				
						
				
				
		
		
    
			
		
    
	
    

    

    • 





Children
	
No Data