Products Mentioned

AD9371 Recommended for New Designs
The AD9371 is a highly integrated, wideband RF transceiver offering dual channel transmitters and receivers, integrated synthesizers, and digital signal...
Datasheet
AD9371 on Analog.com

  • State Verified Answer
  • Replies 10 replies
  • Subscribers 107 subscribers
  • Views 615 views
  • Users 0 members are here
Options
Related 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
can not update iio with zc706+adrv9371



		

			

									
					    mashimaro
					
							

			
				
									
											
			
			
				
  •  Analog Employees  

			
			
			    	
			                    
                
				                on May 25, 2023 
				
			
			
		


				
		

		    		    
		    
		    		      		            		        
Category: Software

    		        		            		    
Product Number:  ad9371, zc706 

    		        		    		    	
			
Hi team,


I try to configure SD card for adrv9371-w/pcbz and zc706 platform. The problem is no IIO GUI showed on the monitor.


I followed the steps from wiki to configure sd-cardhttps://wiki.analog.com/resources/tools-software/linux-software/kuiper-linux.


After I wrote the image file to sd-card, I copied three documents below to BOOT partition.


    

  1. Zynq-zc706-adv7511-adrv937x/BOOT.BIN
    2. 

  2. Zynq-zc706-adv7511-adrv937x/devicetree/dtb
    3. 

  3. Zynq-common/ulmage
    4. 



Then I setup the physical system. The hdmi monitor could not show IIO gui.


How do I solve this problem?

									
			        
		


				
						
        

    
Tags: 
                                            
                 software
                
                                                    
                 ad9371
                
                                                    
                 zc706
                
                                                    
                 Wideband Transceiver IC
                
                                                    
                 RF Integrated Transceivers
                
                                
            

    
    

		

			
						
									
									
						
						
			
			
			
			
		


        
        

					

			





















	

	

					



			








	
	
	
	



Parents
	
    
	

  • 
	
    



	
		
	
	



    
	
    
		
    
							
					
    
		
    
			
													0
							
			
				
									
							        
			
			
			
    •  Analog Employees  
    •  Super User  
    
            
						
                            
            
            				
            
                on May 25, 2023 9:31 AM
            
            
					
    
	
    

		
		
    
					
    I just tried with a clean 2021_R2 Kuiper image card and those files as you mentioned, and for me it opens the GUI and also catches signals in the capture window.
    

    There is a situation when it doesn't capture, and it is the following: if I open IIO Oscilloscope on my computer and connect to the board through IP, and then open it in Kuiper, then indeed the capture is shown only on my computer since is the first one opened. But this is not the case for you.
    

    Anyway, it opens the IIO Oscilloscope GUI in both situations.
    

    Did you try opening a terminal in Kuiper and writing sudo osc to open IIO Oscilloscope? The password for the user <analog> is again <analog>.
    

    Best regards,
    Iulia
    
			
    

		
			
	      

		
		
	
    
	
    
		
    
			
		
    
	
    
	
    
		
						
						
				
						
				
				
		
		
    
			
		
    
	
    

    

    • 

	

  • 
	
    



	
		
	
	



    
	
    
		
    
							
					
    
		
    
			
													0
							
			
				
									
							        
			
			
			
    •  Analog Employees  
    
            
						
                            
            
            				
            
                on May 26, 2023 2:23 AM
            
            
												
						in reply to iulia
					
									
    
	
    

		
		
    
					
    Hi Lulia,
    

    Thanks for your reply.
    

    iulia said:
    In the meantime, could you please tell me what Kuiper image you used? Is it the 2021_r2 one, the latest?
    

    Yes, I used the lasted image document.
    

    Actually I tried to open an serial terminal on PC after setting up the physical system, but nothing printed on the terminal. Maybe I installed the wrong UART driver on PC? Could you tell me which version of UART driver you used?
    
			
    

		
			
	      

		
		
	
    
	
    
		
    
			
		
    
	
    
	
    
		
						
						
				
						
				
				
		
		
    
			
		
    
	
    

    

    • 

	




Reply

    


  • 
	
    



	
		
	
	



    
	
    
		
    
							
					
    
		
    
			
													0
							
			
				
									
							        
			
			
			
    •  Analog Employees  
    
            
						
                            
            
            				
            
                on May 26, 2023 2:23 AM
            
            
												
						in reply to iulia
					
									
    
	
    

		
		
    
					
    Hi Lulia,
    

    Thanks for your reply.
    

    iulia said:
    In the meantime, could you please tell me what Kuiper image you used? Is it the 2021_r2 one, the latest?
    

    Yes, I used the lasted image document.
    

    Actually I tried to open an serial terminal on PC after setting up the physical system, but nothing printed on the terminal. Maybe I installed the wrong UART driver on PC? Could you tell me which version of UART driver you used?
    
			
    

		
			
	      

		
		
	
    
	
    
		
    
			
		
    
	
    
	
    
		
						
						
				
						
				
				
		
		
    
			
		
    
	
    

    

    • 





Children
	
No Data