no-OS code of AD9379A?

Hi,

You used make to build the HDL project right?
can you do the same for no-OS https://github.com/analogdevicesinc/no-OS/commits/master/ad9739a-fmc-ebz/zc706?
According to https://wiki.analog.com/resources/fpga/quick_validation.

Andrei

Thanks for your reply.

I'm sure that I build the HDL project right. I have followed the steps in https://github.com/analogdevicesinc/no-OS/commits/master/ad9739a-fmc-ebz/zc706?. But when I type "make" and enter in the terminal in the "\no-OS\ad9739a-fmc-ebz\zc706" path, a fatal error happens "../src/ad9739a.h:49:10: fatal error: spi.h: No such file or directory". I don't know why.

Hi,

There seems to be a bug in the no-OS master branch. can you please use the 2018_R2 branch.
I will notify my colleagues from the no-Os team.

Andrei

OK. Thank you very much!

The problem before has been soled, thank you. But a new problem occurs!

When the program goes to "ad9739a_setup(&ad9739a_device, &init_param)", "Error: Invalid CHIP ID (0xff)." is shown in the SDK terminal. 

Is the ad9379a connected on the FMC LPC, what is the path selected by clock switch?
Also, check the VADJ.

Andrei

Okay, I'll have a try. Thank you!

I have checked the connection. The ad9739a is connected to the FMC LPC of the ZC706 evaluation board. And the clock path is connected to the ADF4350.

SPI SRC jumper (P2) is on FMC position?
VADJ on zc706, what is the voltage?

Andrei

SPI SRC jumper is on FMC position.

The VADJ on zc706 is 2.5V

SPI SRC jumper is on FMC position.

The VADJ on zc706 is 2.5V

I'm out of the office, I will make a setup tomorrow.

Andrei

Okay. Thank you!

Hi,

No problems for me.
Can you do a test with ad9739a_zc706.zip?

Andrei

Something that I was not aware of "To enable this clock path, jumper CLOCK SOURCE (S1) must be moved to the ADCLK914 position. C102 and C99 on the back of the board also need to be removed from their default position, and then soldered into the vertical position from the large square pad they were previously soldered to and the narrow pads closer to the ADCLK914 (U3). Observe the orientation of the caps before removing them; they must be soldered with their narrow edge against the PCB, and not the wide side as is common with most components." see https://wiki.analog.com/resources/fpga/xilinx/fmc/ad9739a

Andrei

Okay, I'll have a try. Thank you!

I added the sw.elf in my SDK project and run. The same error occurred.

If I want to add some new waves created by myself, how do I do based on the reference design?

Hi,

Can you open xsdb from a terminal or SDK GUI, and manually program the board.

功程292 said:

ad9739a_setup(&ad9739a_device, &init_param)", "Error: Invalid CHIP ID (0xff).

If the above was not resolved, you can't transmit any kind of data.

-extract the files from .hdf archive
-write the bit

fpga -file system_top.bit

    source ps7_init.tcl
    ps7_init
    ps7_post_config

dow sw/Release/sw.elf

-run

con

Have you made the hardware changes suggested above?

Andrei

I do the following steps:

Firstly, I download the hdl(2018-r2) and no-os(2018-r2) on the github. And I use the "make" command to create a vivado 2018.2 project for zc706.

Secondly, I also use the "make" command to create the no-os project of ad9739.

Thirdly, I launch sdk in vivado and I add the existing sdk project of no-os to sdk.

Finally, I run the debug as the following pictures.

Is there any problem in my steps? Thank you!

Hi,

There is no problem with your steps. This is the flow we recommend and everything seems to be ok.
I've worked with people that modified the code, used other tools or had issues with the combination of OS and tool.
This is just my attempt to "play safe" and find the problem faster. I want to exclude any build issues.

Andrei