Two hands cradle a glowing light, illuminating the darkness around them.

EMC: Finding Your Circuit Chi

A Loose Refresher

EMC is the peaceful coexistence of everyone's electronics, here, on this planet. Actually, aircraft, satellites, and spaceships are subjected to EMC performance testing too. In fact, electromagnetic waves have a much greater opportunity to propagate up there as well.

Recapping on Fields

Simply put, any current flowing is synonymous with electromagnetic fields. If your product is not an intentional radiator, it is critical to ensure it does not efficiently emit electromagnetic fields. This is accomplished by containing the fields generated and carefully considering their energy flow.  An example is simply to contain or minimize the flux lines between the forward and reverse current paths. 

 Differential pair, the opposing currents cancel each other’s magnetic fields.

Figure 1:  Differential pair, the opposing currents cancel each other’s magnetic fields.

Antenna as an Example of Poor Design

Thinking about antennas: Your basic ¼-wave dipole antenna (two unterminated conductors pointing in opposite directions) enables efficient radiation and reception of electromagnetic energy within a tuned band. Then you have the loop antenna. You might have noted one sitting on your old TV if you are of my vintage. 

 An actual nearfield scan of a dipole antenna’s tip, electric field.

Figure 2: An actual nearfield scan of a dipole antenna’s tip, electric field.

We design our products with the complete opposite in mind; we wish to avoid inadvertent antenna design. We design to contain the radiation by containing fields between ground layers in our multilayer PCBs or carefully matched differential pair traces, twisted pair, or coaxial cabling. The principle of close-proximity conductors to cancel magnetic fields is used extensively. Referring to Figure 1 above, the magnetic field lines surrounding the conductor with the forward flowing current are tightly coupled to the return current's conductor, directly counteracting and balancing the entire resultant magnetic field. The key is maintaining a good characteristic impedance match, both in and out of band, or understanding the trade-offs of high and low impedance interconnections.

 

How We Might Get Away with Poor Designs

Products such as electronic devices can get away with less-than-ideal designs if, for example, the inadvertently tuned band does not align with the product’s internal communication frequencies or crystal frequencies, especially concerning emissions. Alternatively, from an immunity perspective, the product might receive a lot of 'test' energy but be naturally immune in that range or effectively filter later, ensuring the energy is absorbed or redirected to prevent interference.

 

Back to Energy Flow and Chi

We are still talking energy flow here, ensuring that energy is going only where it's needed. You want every bit of your communication energy, and not a drop more, reproducing the optimal Bit Error Rate, Eye Diagram opening, Signal to Noise Ratio in the receiving technology, and not radiating, heating, or degrading other circuits’ operation. The beauty of strong EMC design, especially in portable devices, is battery efficiency too; any inadvertent radiation or heating drains your battery, though in fairness, only slightly. 

One of the biggest kickers in EMC is mode conversion. We'll discuss the topic in detail, but in short, it's that phenomenon where you are trying your best to keep that balance and symmetry. But the theory has to be replaced with real components, practical limitations, or functional needs. It's when your chi goes out of whack; symmetrical circuitry can no longer be maintained in a design, magnetic flux becomes imbalanced, and a common mode signal is transformed into a differential signal, competing directly with your desired signals. Connectors are crucial and carefully chosen for many functional reasons, but they can sometimes fail, having larger gaps between their moulded connectors than desirable. This may also result in unbalancing ground references, often at a board's edge, where they are more likely to act as an antenna. 

 

What’s Coming

In this blog series, we will take you on an electron's journey through attaining product EMC compliance and examining electromagnetic propagation from near-field to far-field, as well as changes in the Poynting vector, illustrating what it is in products that causes them to fail EMC laboratory test limits. We will also explore the history, origins, and evolution of these emissions limits and immunity test levels.

If curiosity is your way, electronics is your passion, and you care deeply about the force, Lorentz force. Join me again on upcoming blogs.

Read all the blogs in the EMCguy series

Enjoy this topic, test your knowledge, and be entered for a chance to win a $25 gift card. Click here.

Before You Switch


Switching languages will make ADI Explorer unavailable. Resume your session by switching back to English and reopening ADI Explorer.