Wrong Image Format for bootm command

Hi Sushindren,

bootm command is for Uimage

As you were using zimage, you need to use bootz command.

replace the bootm command from your bootargs to bootz and give it a try.

Thanks,

Prasanth R

Hi Prasanth,

I can't get you properly, Are you told to boot with sdcard boot option.

When i am using printenv in the uboot, it shown some arguments,

addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmaf
autoload=no                                                                     
baudrate=115200                                                                 
bootcmd=run ramboot                                                             
bootdelay=2                                                                     
dtbaddr=0x84000000                                                              
dtbfile=sc573-ezkit.dtb                                                         
ethact=dwmac.3100c000                                                           
ethaddr=02:80:ad:20:31:e8                                                       
fdtcontroladdr=8ffcca20                                                         
gatewayip=192.168.0.1                                                           
hostname=sc57x                                                                  
imagefile=zImage                                                             
initramaddr=0x85000000                                                          
initramfile=ramdisk.cpio.xz.u-boot                                              
ipaddr=192.168.0.15                                                             
loadaddr=0x82000000                                                             
loads_echo=1                                                                    
nc=setenv ncip ${serverip};setenv stdin nc;setenv stdout nc;setenv stderr nc    
netmask=255.255.255.0                                                           
nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath},tcp,nf
nfsboot=tftp ${loadaddr} ${nfsfile};run nfsargs;run addip;bootm ${loadaddr};    
nfsfile=zImage                                                               
norboot=tftp ${loadaddr} ${ramfile};run ramargs;run addip;bootm ${loadaddr};    
ramargs=setenv bootargs root=/dev/mtdblock2 rw rootfstype=jffs2 earlyprintk=ser
ramboot=tftp ${loadaddr} ${ramfile};tftp ${initramaddr} ${initramfile};run rama;
ramboot_emmc=mmc rescan;mmc dev 0 0;ext2load mmc 0:1 ${loadaddr} /boot/${ramfil;
ramfile=zImage                                                               
rootpath=/romfs                                                                 
sdcardargs=setenv bootargs root=/dev/mmcblk0p1 rw earlyprintk=serial,uart0,1152
sdcardboot=mmc rescan;mmc dev 0 0;ext2load mmc 0:1 ${loadaddr} /boot/${ramfile};
serverip=192.168.0.2                                                            
stderr=serial@0x31003000                                                        
stdin=serial@0x31003000                                                         
stdout=serial@0x31003000                                                        
ubootfile=u-boot-sc573-ezkit.ldr                                                
update=tftp ${loadaddr} ${ubootfile};sf probe 2:1;sf erase 0 0x80000;sf write $}

Here as you can see i loaded the zImage in the imagefile when run sdcardboot i shown same error, i dont know where i am missing,

If i can't get your point kindly tell elaborately,

Thankyou,

Sushindren

Hi Prasanth,

I can't get you properly, Are you told to boot with sdcard boot option.

When i am using printenv in the uboot, it shown some arguments,

addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmaf
autoload=no                                                                     
baudrate=115200                                                                 
bootcmd=run ramboot                                                             
bootdelay=2                                                                     
dtbaddr=0x84000000                                                              
dtbfile=sc573-ezkit.dtb                                                         
ethact=dwmac.3100c000                                                           
ethaddr=02:80:ad:20:31:e8                                                       
fdtcontroladdr=8ffcca20                                                         
gatewayip=192.168.0.1                                                           
hostname=sc57x                                                                  
imagefile=zImage                                                             
initramaddr=0x85000000                                                          
initramfile=ramdisk.cpio.xz.u-boot                                              
ipaddr=192.168.0.15                                                             
loadaddr=0x82000000                                                             
loads_echo=1                                                                    
nc=setenv ncip ${serverip};setenv stdin nc;setenv stdout nc;setenv stderr nc    
netmask=255.255.255.0                                                           
nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath},tcp,nf
nfsboot=tftp ${loadaddr} ${nfsfile};run nfsargs;run addip;bootm ${loadaddr};    
nfsfile=zImage                                                               
norboot=tftp ${loadaddr} ${ramfile};run ramargs;run addip;bootm ${loadaddr};    
ramargs=setenv bootargs root=/dev/mtdblock2 rw rootfstype=jffs2 earlyprintk=ser
ramboot=tftp ${loadaddr} ${ramfile};tftp ${initramaddr} ${initramfile};run rama;
ramboot_emmc=mmc rescan;mmc dev 0 0;ext2load mmc 0:1 ${loadaddr} /boot/${ramfil;
ramfile=zImage                                                               
rootpath=/romfs                                                                 
sdcardargs=setenv bootargs root=/dev/mmcblk0p1 rw earlyprintk=serial,uart0,1152
sdcardboot=mmc rescan;mmc dev 0 0;ext2load mmc 0:1 ${loadaddr} /boot/${ramfile};
serverip=192.168.0.2                                                            
stderr=serial@0x31003000                                                        
stdin=serial@0x31003000                                                         
stdout=serial@0x31003000                                                        
ubootfile=u-boot-sc573-ezkit.ldr                                                
update=tftp ${loadaddr} ${ubootfile};sf probe 2:1;sf erase 0 0x80000;sf write $}

Here as you can see i loaded the zImage in the imagefile when run sdcardboot i shown same error, i dont know where i am missing,

If i can't get your point kindly tell elaborately,

Thankyou,

Sushindren

Hi Sushindren,

Could you share the exact complete error along with the command you were passing to the u-boot?

Do you zImage copied under /boot/Zimage directory of the SD card? 

could you print the output of # ext2ls mmc 0:1 /boot

Thanks,

Prasanth R

Hi Prasanth,

Apologize for the late reply,

As you mentioned i executed the command,

=> ext2ls mmc 0:1 /boot                                                         
<DIR>       4096 .                                                              
<DIR>       4096 ..                                                             
         4255384 zImage-4.19.0-yocto-standard                                   
<SYM>         28 zImage                                                         
           18488 sc573-ezkit.dtb                                                
=>

when i run sdcard boot its showing wrong image format, i followed the same procedure which was in the link

here i used zImage for this.

=> run sdcardboot                                                               
switch to partitions #0, OK                                                     
mmc0 is current device                                                          
4255384 bytes read in 719 ms (5.6 MiB/s)                                        
Wrong Image Format for bootm command                                            
ERROR: can't get kernel image!

Waiting for the replay

Thanks,

Sushindren

Hi Sushindrean,

It seems your u-boot environment variable was modified,

```

#setenv sdcardboot 'mmc rescan; mmc dev 0 0; ext2load mmc 0:1 ${loadaddr} /boot/${ramfile}; ext2load mmc 0:1 ${dtbaddr} /boot/${dtbfile}; run sdcardargs; bootz ${loadaddr} - ${dtbaddr}'

#run sdcardboot

```

Thanks,

Prasanth R

Hi Prasanth,

Thank you for your support, now its booting partially

In the end it can't able to load the .ldr as well as .db files.

platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
remoteproc remoteproc0: core1-rproc is available
cfg80211: failed to load regulatory.db
remoteproc remoteproc1: core2-rproc is available
remoteproc remoteproc0: Direct firmware load for adi_adsp_core1_fw.ldr failed with error -2
ALSA device list:
  No soundcards found.
remoteproc remoteproc0: powering up core1-rproc
remoteproc remoteproc0: Direct firmware load for adi_adsp_core1_fw.ldr failed with error -2
remoteproc remoteproc0: request_firmware failed: -2
remoteproc remoteproc1: Direct firmware load for adi_adsp_core2_fw.ldr failed with error -2

I think most of the files has loaded this one only a trouble maker for me.

Waiting for your reply from your end.

Thank you,

Sushindren

Hi Sushindren,

Could you reach the userspace login prompt?

I hope that remoteproc won't be an issue. 

Thanks,

Prasanth R

Hi Prasanth,

No i didn't get the login prompt.

It showing like this only and also i can't able to give any commands it's giving the same symbol.

��~<������

Thank you,

Sushindren

Hi Sushindren,

This seems strange on seeing this basic boot issue,  

step 1: 

I recommend following this

#env default -a -f

#run sdcardboot

If the above doesn't help

step2:

I recommend you to follow the below link and build the minimal image, replace the complete u-boot and boot the device with the newly created image

https://wiki.analog.com/resources/tools-software/linuxdsp/docs/quickstartguide/quickstart_sc573

Thanks,

Prasanth R

Hi Prasanth,

Thankyou for your great support , i followed your recommendation of the steps which first step didn't worked for me.

In the second recommendation i used the minimal and fitimage which is mentioned in the quick start guide that one worked for me

but when i incorporate zImage and minimal image it causes and stuck in between while booting itself, i didn't get the login promt also

I surfed regards with this issue also and i found one link and followed the same steps still i am getting the same.

https://wiki.analog.com/resources/tools-software/linuxdsp/docs/quickstartguide/installing/installing_nfsboot

Thank you,

Sushindren