2010-06-28 11:25:00 ISP1760: Scratch test failed.

anoob CS (INDIA)

Message: 90691

for me usb is not working while loading kernel "ISP1760: Scratch test failed." is comming what to do ?

out through terminal is below

U-Boot 2009.08 (ADI-2009R2-pre) (May 12 2010 - 12:29:22)

CPU: ADSP bf561-0.5 (Detected Rev: 0.5) (parallel flash boot)

Board: NPLTSBF201561 board

Support: NPOL Thrikkakara, Kochin-21

Clock: VCO: 500 MHz, Core: 500 MHz, System: 100 MHz

RAM: 128 MB

Flash: 64 MB

*** Warning - bad CRC, using default environment

In: serial

Out: serial

Err: serial

Net: SMC91111-0

Hit any key to stop autoboot: 5 4 3 2 1 0

SMC91111: MAC 02:80:ad:20:31:e8

Using SMC91111-0 device

TFTP from server 192.168.0.2; our IP address is 192.168.0.15

Filename 'uImage'.

Load address: 0x1000000

Loading: * T #################################################################

#################################################################

###########

done

Bytes transferred = 4921193 (4b1769 hex)

## Booting kernel from Legacy Image at 01000000 ...

Image Name: Linux-2.6.28.10-ADI-2009R1.1

Image Type: Blackfin Linux Kernel Image (gzip compressed)

Data Size: 4921129 Bytes = 4.7 MB

Load Address: 00001000

Entry Point: 001cf680

Verifying Checksum ... OK

Uncompressing Kernel Image ... OK

Starting Kernel at = 001cf680

Linux version 2.6.28.10-ADI-2009R1.1 (root@localhost.localdomain) (gcc version 4.1.2 (ADI svn)) #30 Mon Jun 14 15:32:10 IST 2010

bootconsole [early_shadow0] enabled

bootconsole [early_BFuart0] enabled

early printk enabled on early_BFuart0

Board Memory: 128MB

Kernel Managed Memory: 128MB

Memory map:

fixedcode = 0x00000400-0x00000490

text = 0x00001000-0x00130a40

rodata = 0x00130a40-0x00189fe0

bss = 0x0018a000-0x001af5f4

data = 0x001af5f4-0x001c2000

stack = 0x001c0000-0x001c2000

init = 0x001c2000-0x00aa1000

available = 0x00aa1000-0x07eff000

DMA Zone = 0x07f00000-0x08000000

Hardware Trace Active and Enabled

Boot Mode: 2

Compiled for ADSP-BF561 Rev 0.5

Blackfin Linux support by blackfin.uclinux.org/

Processor Speed: 500 MHz core clock and 100 MHz System Clock

NOMPU: setting up cplb tables

Instruction Cache Enabled for CPU0

Data Cache Enabled for CPU0 (write-back)

Data Cache (L2 SRAM) Enabled (write-back)

Built 1 zonelists in Zone order, mobility grouping off. Total pages: 32257

Kernel command line: root=/dev/mtdblock0 rw clkin_hz=50000000 earlyprintk=serial,uart0,115200 console=ttyBF0,115200 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:bf561-npltsbf201561:eth0:off

Configuring Blackfin Priority Driven Interrupts

PID hash table entries: 512 (order: 9, 2048 bytes)

I-pipe 1.10-00: pipeline enabled.

console [ttyBF0] enabled, bootconsole disabled

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Memory available: 118032k/131072k RAM, (9084k init code, 1214k kernel code, 582k data, 1024k dma, 1132k reserved)

Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656)

Security Framework initialized

Mount-cache hash table entries: 512

Blackfin Scratchpad data SRAM: 4 KB

Blackfin L1 Data A SRAM: 16 KB (15 KB free)

Blackfin L1 Data B SRAM: 16 KB (16 KB free)

Blackfin L1 Instruction SRAM: 16 KB (4 KB free)

Blackfin L2 SRAM: 128 KB (128 KB free)

net_namespace: 288 bytes

NET: Registered protocol family 16

Blackfin DMA Controller

npltsbf201561_init(): registering device resources

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 4096 (order: 3, 32768 bytes)

TCP bind hash table entries: 4096 (order: 2, 16384 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

TCP reno registered

NET: Registered protocol family 1

I-pipe: Domain Xenomai registered.

Xenomai: hal/blackfin started.

Xenomai: real-time nucleus v2.4.7 (Andalusia) loaded.

Xenomai: starting native API services.

Xenomai: starting POSIX services.

Xenomai: starting RTDM services.

msgmni has been set to 230

io scheduler noop registered

io scheduler anticipatory registered (default)

io scheduler cfq registered

Serial: Blackfin serial driver

bfin-uart.1: ttyBF0 at MMIO 0xffc00400 (irq = 35) is a BFIN-UART

brd: module loaded

bfin-spi bfin-spi.0: Blackfin on-chip SPI Controller Driver, Version 1.0, regs_base@ffc00500, dma channel@16

isp1760-hcd isp1760-hcd.0: NXP ISP1760 USB Host Controller

isp1760-hcd isp1760-hcd.0: new USB bus registered, assigned bus number 1

ISP1760: Scratch test failed.

isp1760-hcd isp1760-hcd.0: can't setup

isp1760-hcd isp1760-hcd.0: USB bus 1 deregistered

bfin-wdt: initialized: timeout=20 sec (nowayout=0)

TCP cubic registered

NET: Registered protocol family 17

IP-Config: Device `eth0' not found.

Freeing unused kernel memory: 9084k freed

dma_alloc_init: dma_page @ 0x00a9d000 - 256 pages at 0x07f00000

_____________________________________

a8888b. / Welcome to the uClinux distribution \

d888888b. / _ _ \

8P"YP"Y88 / | | |_| __ __ (TM) |

8|o||o|88 _____/ | | _ ____ _ _ \ \/ / |

8' .88 \ | | | | _ \| | | | \ / |

8`._.' Y8. \ | |__ | | | | | |_| | / \ |

d/ `8b. \ \____||_|_| |_|\____|/_/\_\ |

dP . Y8b. \ For embedded processors including |

d8:' " `::88b \ the Analog Devices Blackfin /

d8" 'Y88b \___________________________________/

:8P ' :888

8a. : _a88P For further information, check out:

._/"Yaa_: .| 88P| - blackfin.uclinux.org/

\ YP" `| 8P `. - docs.blackfin.uclinux.org/

/ \.___.d| .' - www.uclinux.org/

`--..__)8888P`._.' jgs/a:f - www.analog.com/blackfin

Have a lot of fun...

BusyBox v1.13.4 (2010-06-11 14:20:14 IST) built-in shell (msh)

Enter 'help' for a list of built-in commands.

root:/>

Partner Forums

Partner Libraries

2010-06-28 11:25:00 ISP1760: Scratch test failed.