2008-02-29 10:28:04 2008R1-RC2 cannot work on BF527 with 2 pics 32MB SDRAM (32M x8)
C.C Lu (TAIWAN)
Message: 51903 Hi All,
My BF527 (not BF527c) uses two pics of 32MB SDRAM (32M x 8).
When I downloads uclinux image in u-boot, then boots the image.
It stops in "Starting Kernel at = 14c000".
How to fix this problem?
QuoteReplyEditDelete
2008-02-29 11:20:52 Re: 2008R1-RC2 cannot work on BF527 with 2 pics 32MB SDRAM (32M x8)
Michael Hennerich (GERMANY)
Message: 51907 What is your kernel command line?
-Michael
QuoteReplyEditDelete
2008-02-29 12:16:45 Re: 2008R1-RC2 cannot work on BF527 with 2 pics 32MB SDRAM (32M x8)
Mike Frysinger (UNITED STATES)
Message: 51910 an error like that lacks any real information to give you suggestions on how to resolve it ... you'll need to do more debugging on your side
check out this page:
http://docs.blackfin.uclinux.org/doku.php?id=post_mortem
QuoteReplyEditDelete
2008-03-02 22:52:06 Re: 2008R1-RC2 cannot work on BF527 with 2 pics 32MB SDRAM (32M x8)
C.C Lu (TAIWAN)
Message: 51969
U-Boot 1.1.6 (ADI-2008R1) (Feb 29 2008 - 22:16:05)
CPU: ADSP bf527-0.0 (Detected Rev: 0.0)
Board: ADI BF527 EZ-Kit board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
RAM: 64 MB
Flash: 4 MB
In: serial
Out: serial
Err: serial
Net: Blackfin EMAC
MAC: 4E:40:57:65:67:5C
I2C: ready
Hit any key to stop autoboot: 0
bfin> tftp 0x1000000 linux_527
Using Blackfin EMAC device
TFTP from server 192.168.0.232; our IP address is 192.168.0.15
Filename 'linux_527'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#####################
done
Bytes transferred = 3434828 (34694c hex)
bfin> bootm
## Booting image at 01000000 ...
Image Name: Linux-2.6.22.18-ADI-2008R1-svn
Created: 2008-02-29 1:54:18 UTC
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 3434764 Bytes = 3.3 MB
Load Address: 00001000
Entry Point: 0014c000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 14c000
---------------------------------------------------------------------------------------------------------------------------------------------------------
U-Boot 1.1.6 (ADI-2008R1) (Feb 29 2008 - 22:16:05)
CPU: ADSP bf527-0.0 (Detected Rev: 0.0)
Board: ADI BF527 EZ-Kit board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
RAM: 64 MB
Flash: 4 MB
In: serial
Out: serial
Err: serial
Net: Blackfin EMAC
MAC: 4E:40:57:65:67:5C
I2C: ready
Hit any key to stop autoboot: 0
bfin> tftp 0x1000000 linux_527
Using Blackfin EMAC device
TFTP from server 192.168.0.232; our IP address is 192.168.0.15
Filename 'linux_527'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#####################
done
Bytes transferred = 3434828 (34694c hex)
bfin> md 0x0066f0e4
0066f0e4: 4c3e353c 78756e69 72657620 6e6f6973 <5>Linux version
0066f0f4: 362e3220 2e32322e 412d3831 322d4944 2.6.22.18-ADI-2
0066f104: 52383030 76732d31 7628206e 65636e69 008R1-svn (vince
0066f114: 6c40746e 6c61636f 74736f68 636f6c2e nt@localhost.loc
0066f124: 6f646c61 6e69616d 67282029 76206363 aldomain) (gcc v
0066f134: 69737265 34206e6f 322e312e 44412820 ersion 4.1.2 (AD
0066f144: 76732049 2029296e 34343123 69724620 I svn)) #144 Fri
0066f154: 62654620 20393220 353a3930 34313a34 Feb 29 09:54:14
0066f164: 54534320 30303220 00000a38 00000000 CST 2008.......
0066f174: 00000000 00000000 00000000 00000000 ................
0066f184: 00000000 00000000 00000000 00000000 ................
0066f194: 00000000 00000000 00000000 00000000 ................
0066f1a4: 00000000 00000000 00000000 00000000 ................
0066f1b4: 00000000 00000000 00000000 00000000 ................
0066f1c4: 00000000 00000000 00000000 00000000 ................
0066f1d4: 00000000 00000000 00000000 00000000 ................
bfin> md 0x0066f054
0066f054: 00000000 0000008a 0000008a 00000000 ................
0066f064: 00000000 00000000 00000000 00000000 ................
0066f074: 00000000 00000000 00000000 00000000 ................
0066f084: 00000000 00000000 00000000 00000000 ................
0066f094: 00000000 00000000 00000000 00000000 ................
0066f0a4: 00000000 00000000 00000000 00000000 ................
0066f0b4: 00000000 00000000 00000000 00000000 ................
0066f0c4: 00000000 00000000 00000000 00000000 ................
0066f0d4: 00000000 00000000 00000000 00000000 ................
0066f0e4: 4c3e353c 78756e69 72657620 6e6f6973 <5>Linux version
0066f0f4: 362e3220 2e32322e 412d3831 322d4944 2.6.22.18-ADI-2
0066f104: 52383030 76732d31 7628206e 65636e69 008R1-svn (vince
0066f114: 6c40746e 6c61636f 74736f68 636f6c2e nt@localhost.loc
0066f124: 6f646c61 6e69616d 67282029 76206363 aldomain) (gcc v
0066f134: 69737265 34206e6f 322e312e 44412820 ersion 4.1.2 (AD
0066f144: 76732049 2029296e 34343123 69724620 I svn)) #144 Fri
bfin>
QuoteReplyEditDelete
2008-03-02 23:26:19 Re: 2008R1-RC2 cannot work on BF527 with 2 pics 32MB SDRAM (32M x8)
Yi Li (CHINA)
Message: 51972 You may try to enable early printk:
http://docs.blackfin.uclinux.org/doku.php?id=post_mortem#early_printk_compiled_into_the_kernel
As Michael asked, what is your kernel command line? Sometimes if the console is not set correctly, the boot message will not be displayed.
QuoteReplyEditDelete
2008-03-03 00:12:59 Re: 2008R1-RC2 cannot work on BF527 with 2 pics 32MB SDRAM (32M x8)
C.C Lu (TAIWAN)
Message: 51973 I enable 'early printk' and set bootargs 'root=/dev/mtdblock0 rw earlyprintk=serial,uart0,57600 console=tty0 console=ttyBF0,57600'.
But it stops in 'Starting Kernel at = 14c000' when I bootm image.
What is mean of kernel command line?
QuoteReplyEditDelete
2008-03-03 01:39:39 Re: 2008R1-RC2 cannot work on BF527 with 2 pics 32MB SDRAM (32M x8)
Robin Getz (UNITED STATES)
Message: 51978 C.C,:
0.0 BF527 is not supported. Upgrade your development silicon
http://docs.blackfin.uclinux.org/doku.php?id=uclinux-dist:features
Does the following image work?
http://blackfin.uclinux.org/gf/download/frsrelease/345/3525/uImage-SVN-bf527-ezkit
-Robin
QuoteReplyEditDelete
2008-03-03 02:16:36 Re: 2008R1-RC2 cannot work on BF527 with 2 pics 32MB SDRAM (32M x8)
C.C Lu (TAIWAN)
Message: 51981 Robin:
The uImage-SVN-bf527-ezkit image is still not work.
The Silicon of BF527 Ezkit is Rev 0.0. My BF527 board is Rev 0.1.
When I choice silicon rev 0.1 in menuconfig, it has compiling error message of "ccl: error: -mcpu=bf527-0.1 has invalid silicon revision."
My board uses 2 pics 32Mx8 SDRAM instead of 1 pic 32Mx16 SDRAM of BF527-ezkit.
Do modify some settings of this collocation in the kernel or menuconfig?
A2V56S30BTP-G75.pdf
QuoteReplyEditDelete
2008-03-12 13:19:02 Re: 2008R1-RC2 cannot work on BF527 with 2 pics 32MB SDRAM (32M x8)
Robin Getz (UNITED STATES)
Message: 52399 CC:
Sorry for delay - did you get things figured out?
-Robin
QuoteReplyEditDelete
2008-03-14 09:21:28 Re: 2008R1-RC2 cannot work on BF527 with 2 pics 32MB SDRAM (32M x8)
C.C Lu (TAIWAN)
Message: 52544 Robin:
It works fine. I make a mistake.
My BF527 board use uart0 for rs-232, not uart1.
I am modified U-Boot to uart0, but I don't enable uart0 driver in uClinux.
Sorry.