2008-08-21 05:14:53 isp1761 + usb pc camera,init isoc: usb_submit_urb(1) ret -12

miaolf miao (CHINA)

Message: 60815

Hi! ALL:

my board is bf549+isp1761,usb pc camera is z-star.driver see attach file.

U-Boot 1.1.6-svn (ADI-2007R2-pre) (Jul 12 2008 - 14:10:00)

CPU: ADSP bf548-0.0 (Detected Rev: 0.1)

Board: ADI BF548 EZ-Kit board

Support: http://blackfin.uclinux.org/

Clock: VCO: 400 MHz, Core: 400 MHz, System: 133 MHz

SDRAM: 64 MB

FLASH: 1 MB

In: serial

Out: serial

Err: serial

NAND: 128 MiB

dm9000 i/o: 0x2b900000, id: 0x90000a46

MAC: 02:80:ad:24:31:e8

02:80:ad:24:31:e8:

could not establish link

Hit any key to stop autoboot: 5 0

bfin>

bfin> tftp 1000000 549.linux.new

dm9000 i/o: 0x2b900000, id: 0x90000a46

MAC: 02:80:ad:24:31:e8

02:80:ad:24:31:e8:

operating at 100M full duplex mode

TFTP from server 192.168.6.161; our IP address is 192.168.6.200

Filename '549.linux.new'.

Load address: 0x1000000

Loading: * #################################################################

#################################################################

#################################################

done

Bytes transferred = 9233836 (8ce5ac hex)

bfin> bootm

## Booting image at 01000000 ...

Bad Magic Number

bfin> bootelf

Loading .text @ 0x00001000 (1753632 bytes)

Loading .rodata @ 0x001ae000 (473180 bytes)

Loading __ksymtab @ 0x0022185c (17888 bytes)

Loading __ksymtab_gpl @ 0x00225e3c (5704 bytes)

Loading __ksymtab_gpl_future @ 0x00227484 (24 bytes)

Loading __ksymtab_strings @ 0x0022749c (58060 bytes)

Loading __param @ 0x00235768 (1360 bytes)

Loading .data @ 0x00236000 (122880 bytes)

Loading .init.text @ 0x00254000 (132620 bytes)

Loading .init.data @ 0x0027460c (13080 bytes)

Loading .init.setup @ 0x00277924 (624 bytes)

Loading .initcall.init @ 0x00277b94 (612 bytes)

Loading .con_initcall.init @ 0x00277df8 (8 bytes)

Loading .init.ramfs @ 0x00277e00 (5876224 bytes)

Loading .text_l1 @ 0xffa00000 (5736 bytes)

sh_addr: FFA00000, p_paddr: 00812800

Loading from: 01813000 to 00812800, size: 5736

Loading .data_l1 @ 0xff800000 (192 bytes)

sh_addr: FF800000, p_paddr: 00813E68

Loading from: 01815000 to 00813E68, size: 192

Clearing .bss @ 0x00814000 (94192 bytes)

## Starting application at 0x00254000 ...

Linux version 2.6.22.19-ADI-2008R1.5-svn (root@fedora8) (gcc version 4.1.2 (ADI svn)) #76 Thu Aug 21 15:03:29 CST 2008

Hardware Trace Active and Enabled

Reset caused by Software reset

Compiled for ADSP-BF548 Rev 0.0

Warning: Compiled for Rev 0, but running on Rev 1

Blackfin Linux support by http://blackfin.uclinux.org/

Processor Speed: 400 MHz core clock and 133 MHz System Clock

Board Memory: 64MB

Kernel Managed Memory: 64MB

Memory map:

text = 0x00001000-0x001ad220

rodata = 0x001ae000-0x00235cb8

data = 0x00236000-0x00254000

stack = 0x00236000-0x00238000

init = 0x00254000-0x00814000

bss = 0x00814000-0x0082aff0

available = 0x0082aff0-0x03dff000

DMA Zone = 0x03e00000-0x04000000

NOMPU: setting up cplb tables for global access

Instruction Cache Enabled

Data Cache Enabled (write-through)

Built 1 zonelists. Total pages: 15748

Kernel command line: console=ttyBF0,57600

Configuring Blackfin Priority Driven Interrupts

PID hash table entries: 256 (order: 8, 1024 bytes)

Console: colour dummy device 80x25

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory available: 54540k/65536k RAM, (5888k init code, 1712k kernel code, 759k data, 2048k dma, 588k reserved)

Blackfin Scratchpad data SRAM: 4 KB

Blackfin Data A SRAM: 16 KB (15 KB free)

Blackfin Data B SRAM: 16 KB (16 KB free)

Blackfin Instruction SRAM: 48 KB (42 KB free)

Security Framework v1.0.0 initialized

Mount-cache hash table entries: 512

NET: Registered protocol family 16

Blackfin GPIO Controller

Blackfin DMA Controller

ezkit_init(): registering device resources

bfin_isp1761_init(): registering device resources

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

io scheduler noop registered

io scheduler anticipatory registered (default)

io scheduler cfq registered

bf54x-lq043: FrameBuffer initializing...

dma_alloc_init: dma_page @ 0x03a37000 - 512 pages at 0x03e00000

Console: switching to colour frame buffer device 80x24

bfin-otp: initialized

bfin-wdt: initialized: timeout=20 sec (nowayout=0)

Serial: Blackfin serial driver

bfin-uart.1: ttyBF0 at MMIO 0xffc02000 (irq = 48) is a BFIN-UART

RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize

smsc911x: Driver version 2007-07-13.

Linux video capture interface: v2.00

scsi0 : pata-bf54x

ata1: PATA max UDMA/100 cmd 0x00000000 ctl 0xffc03800 bmdma 0x00000000 irq 68

physmap platform flash device: 00400000 at 20000000

physmap-flash physmap-flash.0: map_probe failed

bf5xx-nand bf5xx-nand.0: page_size=256, data_width=8, wr_dly=3, rd_dly=3

NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)

Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":

0x00000000-0x00400000 : "Linux Kernel"

0x00400000-0x10000000 : "File System"

mtd: partition "File System" extends beyond the end of device "NAND 128MiB 3,3V 8-bit" -- size truncated to 0x7c00000

bfin-spi bfin-spi.0: Blackfin BF5xx on-chip SPI Contoller Driver, Version 1.0, regs_base@ffc00500, dma channel@4

bfin-spi bfin-spi.1: Blackfin BF5xx on-chip SPI Contoller Driver, Version 1.0, regs_base@ffc02300, dma channel@5

drivers/usb/host/pehcd/hal/hal_pxa.c: pid 8210, vid 0015

drivers/usb/host/pehcd/hal/hal_pxa.c: controller address 0023a6c0

drivers/usb/host/pehcd/hal/hal_pxa.c: isp1761_register_driver(drv=0024b2bc)

isp1761 isp1761.0: PHILIPS ISP1761

isp1761 isp1761.0: new USB bus registered, assigned bus number 1

isp1761 isp1761.0: irq 212, io mem 0x00000000

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

drivers/usb/host/pehcd/hal/hal_pxa.c: Registered Driver Philips

drivers/usb/host/pehcd/host/pehci.c: Host Driver has been Registered

Initializing USB Mass Storage driver...

usb 1-1: new high speed USB device using isp1761 and address 2

usb 1-1: configuration #1 chosen from 1 choice

hub 1-1:1.0: USB hub found

hub 1-1:1.0: 3 ports detected

usb 1-1.3: new full speed USB device using isp1761 and address 3

usb 1-1.3: configuration #1 chosen from 1 choice

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

input: bf54x-keys as /class/input/input0

bf54x-keys: Blackfin BF54x Keypad registered IRQ 76

rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0

i2c /dev entries driver

i2c-bfin-twi i2c-bfin-twi.1: Blackfin BF5xx on-chip I2C TWI Contoller Driver, Version 1.8, regs_base@ffc02200

usbcore: registered new interface driver usbhid

drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver

Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).

ASoC version 0.13.1

dma rx:0 tx:1, err irq:10, regs:ffc00800

AD1980 SoC Audio Codec

asoc: AC97 <-> bf5xx-ac97 mapping ok

AD1980 AC97 reset failed

AC97 link error

soc-audio: probe of soc-audio failed with error -5

ALSA device list:

No soundcards found.

TCP cubic registered

NET: Registered protocol family 1

NET: Registered protocol family 17

rtc-bfin rtc-bfin: setting the system clock to 1984-06-11 13:29:49 (455808589)

Freeing unused kernel memory: 5888k freed

_____________________________________

a8888b. / Welcome to the uClinux distribution \

d888888b. / _ _ \

8P"YP"Y88 / | | |_| __ __ (TM) |

8|o||o|88 _____/ | | _ ____ _ _ \ \/ / |

8' .88 \ | | | | _ \| | | | \ / |

8`._.' Y8. \ | |__ | | | | | |_| | / \ |

d/ `8b. \ \____||_|_| |_|\____|/_/\_\ |

dP . Y8b. \ For embedded processors including |

d8:' " `::88b \ the Analog Devices Blackfin /

d8" 'Y88b \___________________________________/

:8P ' :888

8a. : _a88P For further information, check out:

._/"Yaa_: .| 88P| - http://blackfin.uclinux.org/

\ YP" `| 8P `. - http://docs.blackfin.uclinux.org/

/ \.___.d| .' - http://www.uclinux.org/

`--..__)8888P`._.' jgs/a:f - https://www.analog.com/blackfin

Have a lot of fun...

BusyBox v1.4.1 (2008-08-20 16:56:51 CST) Built-in shell (msh)

Enter 'help' for a list of built-in commands.

root:/> modprobe gspca

drivers/usb/media/gspcav1-20070508/gspca_core.c: USB GSPCA camera found.(ZC3XX)

drivers/usb/media/gspcav1-20070508/gspca_core.c: [spca5xx_probe:4111] Camera type JPEG

drivers/usb/media/gspcav1-20070508/Vimicro/zc3xx.h: [zc3xx_config:515] Sensor ID:11

drivers/usb/media/gspcav1-20070508/Vimicro/zc3xx.h: [zc3xx_config:607] Find Sensor MI0360

drivers/usb/media/gspcav1-20070508/gspca_core.c: [spca5xx_getcapability:1228] maxw 640 maxh 480 minw 176 minh 144

usbcore: registered new interface driver gspca

drivers/usb/media/gspcav1-20070508/gspca_core.c: gspca driver 01.00.18 registered

root:/>

root:/> vidcat -t jpeg -d /dev/video0 -p c -o test.jpeg

drivers/usb/media/gspcav1-20070508/gspca_core.c: [gspca_set_isoc_ep:907] ISO EndPoint found 0x81 AlternateSet 7

drivers/usb/media/gspcav1-20070508/gspca_core.c: init isoc: usb_submit_urb(1) ret -12

drivers/usb/media/gspcav1-20070508/gspca_core.c: [spca5xx_open:1967] DEALLOC error on init_Isoc