2008-11-27 10:28:11 Help on installing the uclinux
Ivan Antonio (PORTUGAL)
Message: 65912
Hi!
My board is the BF537 STAMP, i already have done the image with the comands make xconfig, make dep and make. Rigth now i have to put the image on the board right? I supose i must do it with U-boot? I am trying to do it with serial port with minicom.
QuoteReplyEditDelete
2008-11-27 10:30:56 Re: Help on installing the uclinux
Ivan Antonio (PORTUGAL)
Message: 65913
When i start the minicom and turn on the board this appear
ivan@ivan-desktop:~/uClinux$ minicom
Welcome to minicom 2.3-rc1
OPTIONS: I18n
Compiled on Dec 10 2007, 10:36:19.
Port /dev/ttyS0
Press CTRL-A Z for help on special keys
icache_enable
U-Boot 1.1.6-svn (ADI-2007R1) (Oct 4 2007 - 12:42:05)
CPU: ADSP BF537 Rev.: 0.3
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 500 MHz, Core: 500 MHz, System: 100 MHz
SDRAM: 64 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: BF537 ETHERNET
I2C: ready
autoboot in 2 seconds: press space to stop
## Booting image at 20020000 ...
Image Name: uClinux Kernel and ext2
Created: 2007-08-20 8:46:28 UTC
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 3915339 Bytes = 3.7 MB
Load Address: 00001000
Entry Point: 00001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 1000
Linux version 2.6.19.3-ADI-2007R1.1-svn (root@sevens) (gcc version 4.1.1 (ADI 07
Warning: limiting memory to 53MB due to hardware anomaly 05000263
Blackfin support (C) 2004-2007 Analog Devices, Inc.
Compiled for ADSP-BF537 Rev 0.2
Warning: Compiled for Rev 2, but running on Rev 3
Blackfin Linux support by http://blackfin.uclinux.org/
Processor Speed: 500 MHz core clock and 100 Mhz System Clock
Board Memory: 64MB
Kernel Managed Memory: 64MB
Memory map:
text = 0x00001000-0x00114758
init = 0x00115000-0x00123c40
data = 0x00125d84-0x0015c240
stack = 0x00126000-0x00128000
bss = 0x0015c240-0x0016a2e0
available = 0x0016a2e0-0x03500000
rootfs = 0x03500000-0x03f00000
DMA Zone = 0x03f00000-0x04000000
Instruction Cache Enabled
Data Cache Enabled (write-through)
Hardware Trace Enabled
Built 1 zonelists. Total pages: 13462
Kernel command line: root=/dev/mtdblock0 rw
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Physical pages: 3500
Memory available: 52224k/64360k RAM, (59k init code, 1101k kernel code, 56k dat)
Blackfin Scratchpad data SRAM: 4 KB
Blackfin DATA_A SRAM: 16 KB
Blackfin DATA_B SRAM: 16 KB
Blackfin Instruction SRAM: 48 KB
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Blackfin GPIO Controller
Blackfin DMA Controller
stamp_init(): registering device resources
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler cfq registered
Dynamic Power Management Controller Driver v0.1: major=10, minor = 254
Serial: Blackfin serial driver
bfin-uart.1: ttyBF0 at MMIO 0xffc00400 (irq = 18) is a BFIN-UART
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Blackfin mac net device registered
uclinux[mtd]: RAM probe address=0x3500000 size=0xa00000
Creating 1 MTD partitions on "RAM":
0x00000000-0x00a00000 : "ROMfs"
uclinux[mtd]: set ROMfs:EXT2 to be root filesystem
rtc-bfin rtc-bfin: rtc intf: sysfs
rtc-bfin rtc-bfin: rtc intf: proc
rtc-bfin rtc-bfin: rtc intf: dev (254:0)
rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
rtc-bfin rtc-bfin: setting the system clock to 2014-11-10 02:33:32 (1415586812)
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 56k freed (0x115000 - 0x122000)
dma_alloc_init: dma_page @ 0x0011d000 - 256 pages at 0x03f00000
Welcome to:
____ _ _
/ __| ||_| _ _
_ _| | | | _ ____ _ _ \ \/ /
| | | | | | || | _ \| | | | \ /
| |_| | |__| || | | | | |_| | / \
| ___\____|_||_|_| |_|\____|/_/\_\
|_|
For further information see:
BusyBox v1.4.1 (2007-08-20 16:36:35 CST) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
root:~>
i am on the right way our not?
QuoteReplyEditDelete
2008-11-27 10:32:31 Re: Help on installing the uclinux
Ian Jeffray (UNITED KINGDOM)
Message: 65914
WIKI !
http://docs.blackfin.uclinux.org/doku.php?id=bootloaders:u-boot:serial_port_loading_files
QuoteReplyEditDelete
2008-11-27 10:47:08 Re: Help on installing the uclinux
Ivan Antonio (PORTUGAL)
Message: 65915
Ian jeffray sorry to disturb you again
i do what the wiki say... i try to send the file:
____ _ _
/ __| ||_| _ _
_ _| | | | _ ____ _ _ \ \/ /
| | | | | | || | _ \| | | | \ /
| |_| | |__| || | | | | |_| | / \
| ___\____|_||_|_| |_|\____|/_/\_\
|_| +-----------[ymodem upload - Press CTRL-C to quit]------------+
| TIMEOUT |
For furth|B00000000000000B00000000000000: not foundroot:~> Retry 0: Got|
http://ww| TIMEOUT |
http://bl| |
|Transfer incomplete |
| |
| READY: press any key to continue...
and have this error. can u help me?
QuoteReplyEditDelete
2008-11-27 11:25:44 Re: Help on installing the uclinux
Ian Jeffray (UNITED KINGDOM)
Message: 65917
Ian jeffray sorry to disturb you again
i do what the wiki say... i try to send the file:
____ _ _
/ __| ||_| _ _
_ _| | | | _ ____ _ _ \ \/ /
| | | | | | || | _ \| | | | \ /
| |_| | |__| || | | | | |_| | / \
| ___\____|_||_|_| |_|\____|/_/\_\
|_| +-----------[ymodem upload - Press CTRL-C to quit]------------+
| TIMEOUT |
For furth|B00000000000000B00000000000000: not foundroot:~> Retry 0: Got|
http://ww| TIMEOUT |
http://bl| |
|Transfer incomplete |
| |
| READY: press any key to continue...
and have this error. can u help me?
---
Looks like you're blindly talking y-modem to a linux command prompt. That's never going to work. Sounds like you might need a bit of a primer on what kind of OS Linux is to start with. Spend some minutes/hours with the friendly Wiki. It's rather good.
You need to hit a key when u-boot asks you to do so, to get in to u-boot itself, rather than letting it boot in to Linux.
QuoteReplyEditDelete
2008-11-27 12:21:27 Re: Help on installing the uclinux
Jim Donelson (UNITED STATES)
Message: 65919
You really need to connect the board to your lan. The wiki will explain how get uboot the dhcp etc.
Also DO NOT FLASH UNTIL YOU TEST THE IMAGE. And the best way is to TFTP the image using uboot.
Read the doku-wiki.
QuoteReplyEditDelete
2008-11-27 12:21:34 Re: Help on installing the uclinux
Ivan Antonio (PORTUGAL)
Message: 65920
ok thx for your help