[#4570] Nothing shows on lcd when try directfb on bf537-stamp with usb mouse plugged in
Submitted By: Vivi Li
Open Date
2008-10-29 03:36:19 Close Date
2008-11-19 03:11:33
Priority:
Medium Assignee:
Graf Yang
Status:
Closed Fixed In Release:
N/A
Found In Release:
N/A Release:
Category:
Output to Screen Board:
STAMP
Processor:
BF537 Silicon Revision:
Is this bug repeatable?:
Yes Resolution:
Fixed
Uboot version or rev.:
Toolchain version or rev.:
toolchain-2008_Oct_10
App binary format:
N/A
Summary: Nothing shows on lcd when try directfb on bf537-stamp with usb mouse plugged in
Details:
For BF537 with isp1362 usb board and lq035 tftlcd, try directfb on it, nothing shows up in screen.
Config files are attached and bellow is the log:
--
Linux version 2.6.26.5-ADI-2009R1-pre-svn5488 (test@107-local) (gcc version 4.1.2 (ADI svn)) #124 Wed Oct 29 16:19:27 CST 2008
console [early_BFuart0] enabled
early printk enabled on early_BFuart0
Warning: limiting memory to 56MB due to hardware anomaly 05000263
Board Memory: 64MB
Kernel Managed Memory: 64MB
Memory map:
fixedcode = 0x00000400-0x00000490
text = 0x00001000-0x00140b40
rodata = 0x00140b40-0x001a3f40
bss = 0x001a3f40-0x001b75d0
data = 0x001b75d0-0x001cc000
stack = 0x001ca000-0x001cc000
init = 0x001cc000-0x0062c000
available = 0x0062c000-0x037ff000
DMA Zone = 0x03f00000-0x04000000
Hardware Trace Active and Enabled
Blackfin support (C) 2004-2008 Analog Devices, Inc.
Compiled for ADSP-BF537 Rev 0.2
Blackfin Linux support by blackfin.uclinux.org/
Processor Speed: 500 MHz core clock and 100 MHz System Clock
NOMPU: setting up cplb tables for global access
Instruction Cache Enabled
Data Cache Enabled (write-through)
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 14223
Kernel command line: root=/dev/mtdblock0 rw earlyprintk=serial,uart0,57600 console=tty0 console=ttyBF0,57600 ip=10.100.4.50:10.f
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x25
console [tty0] enabled
Linux version 2.6.26.5-ADI-2009R1-pre-svn5488 (test@107-local) (gcc version 4.1.2 (ADI svn)) #124 Wed Oct 29 16:19:27 CST 2008
console [early_BFuart0] enabled
early printk enabled on early_BFuart0
Warning: limiting memory to 56MB due to hardware anomaly 05000263
Board Memory: 64MB
Kernel Managed Memory: 64MB
Memory map:
fixedcode = 0x00000400-0x00000490
text = 0x00001000-0x00140b40
rodata = 0x00140b40-0x001a3f40
bss = 0x001a3f40-0x001b75d0
data = 0x001b75d0-0x001cc000
stack = 0x001ca000-0x001cc000
init = 0x001cc000-0x0062c000
available = 0x0062c000-0x037ff000
DMA Zone = 0x03f00000-0x04000000
Hardware Trace Active and Enabled
Blackfin support (C) 2004-2008 Analog Devices, Inc.
Compiled for ADSP-BF537 Rev 0.2
Blackfin Linux support by blackfin.uclinux.org/
Processor Speed: 500 MHz core clock and 100 MHz System Clock
NOMPU: setting up cplb tables for global access
Instruction Cache Enabled
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 14223
Kernel command line: root=/dev/mtdblock0 rw earlyprintk=serial,uart0,57600 console=tty0 console=ttyBF0,57600 ip=10.100.4.50:10.f
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x25
console [tty0] enabled
console handover: boot [early_BFuart0] -> real [ttyBF0]
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory available: 50436k/65536k RAM, (4480k init code, 1278k kernel code, 558k data, 1024k dma, 7760k reserved)
Security Framework initialized
Mount-cache hash table entries: 512
Blackfin Scratchpad data SRAM: 4 KB
Blackfin L1 Data A SRAM: 16 KB (15 KB free)
Blackfin L1 Data B SRAM: 16 KB (16 KB free)
Blackfin L1 Instruction SRAM: 48 KB (41 KB free)
net_namespace: 192 bytes
NET: Registered protocol family 16
Blackfin GPIO Controller
Blackfin DMA Controller
stamp_init(): registering device resources
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
msgmni has been set to 98
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler cfq registered
bf537-lq035: FrameBuffer initializing...<6>dma_alloc_init: dma_page @ 0x00950000 - 256 pages at 0x03f00000
Console: switching to colour frame buffer device 40x15
Done.
Serial: Blackfin serial driver
bfin-uart.1: ttyBF0 at MMIO 0xffc00400 (irq = 18) is a BFIN-UART
brd: module loaded
bfin_mac_mdio: probed
bfin_mac: attached PHY driver [SMSC LAN83C185] (mii_bus:phy_addr=0:01, irq=-1, mdc_clk=2500000Hz(mdc_div=19)@sclk=100MHz)
bfin_mac bfin_mac.0: Blackfin on-chip Ethernet MAC driver, Version 1.1
driver isp1362-hcd, 2005-04-04
isp1362-hcd isp1362-hcd.0: ISP1362 Host Controller
isp1362-hcd isp1362-hcd.0: new USB bus registered, assigned bus number 1
isp1362_hc_reset:
isp1362-hcd isp1362-hcd.0: irq 53, io mem 0x20360000
isp1362_hc_start:
isp1362-hcd isp1362-hcd.0: ISP1362 Memory usage:
isp1362-hcd isp1362-hcd.0: ISTL: 2 * 256: 512 @ $0000:$0100
isp1362-hcd isp1362-hcd.0: INTL: 16 * ( 64+8): 1152 @ $0200
isp1362-hcd isp1362-hcd.0: ATL : 32 * ( 64+8): 2304 @ $0680
isp1362-hcd isp1362-hcd.0: USED/FREE: 3968 128
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ISP1362 Host Controller, irq 53
sl811: driver sl811-hcd, 19 May 2005
sl811-hcd sl811-hcd.0: SL811HS v1.5
sl811-hcd sl811-hcd.0: new USB bus registered, assigned bus number 2
sl811-hcd sl811-hcd.0: irq 54, io mem 0x20340000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb 1-2: new low speed USB device using isp1362-hcd and address 2
mice: PS/2 mouse device common for all mice
usb 1-2: configuration #1 chosen from 1 choice
usb 2-1: new low speed USB device using sl811-hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver appletouch
rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0
i2c /dev entries driver
i2c-bfin-twi i2c-bfin-twi.0: Blackfin BF5xx on-chip I2C TWI Contoller, regs_base@ffc01400
usbcore: registered new interface driver i2c-tiny-usb
bfin-wdt: initialized: timeout=20 sec (nowayout=0)
input: Dell Dell USB Keyboard as /class/input/input0
input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-isp1362-hcd.0-2
input: HID 04b3:3107 as /class/input/input1
input: USB HID v11.10 Mouse [HID 04b3:3107] on usb-sl811-hcd.0-1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
rtc-bfin rtc-bfin: setting system clock to 1970-01-01 00:42:03 UTC (2523)
IP-Config: Complete:
device=eth0, addr=10.100.4.50, mask=255.255.255.0, gw=10.100.4.174,
host=bf537-stamp, domain=, nis-domain=(none),
bootserver=10.100.4.174, rootserver=10.100.4.174, rootpath=
Freeing unused kernel memory: 4480k freed
_________________________________P__HY: 0:01 - Link is Up - 100/Full
a8888b. / Welcome to the uClinux distribution \
d888888b. / _ _ \
8P"YP"Y88 / | | |_| __ __ (TM) |
8|o||o|88 _____/ | | _ ____ _ _ \ \/ / |
8' .88 \ | | | | _ \| | | | \ / |
8`._.' Y8. \ | |__ | | | | | |_| | / \ |
d/ `8b. \ \____||_|_| |_|\____|/_/\_\ |
dP . Y8b. \ For embedded processors including |
d8:' " `::88b \ the Analog Devices Blackfin /
d8" 'Y88b \___________________________________/
:8P ' :888
8a. : _a88P For further information, check out:
._/"Yaa_: .| 88P| - blackfin.uclinux.org/
\ YP" `| 8P `. - docs.blackfin.uclinux.org/
/ \.___.d| .' - www.uclinux.org/
`--..__)8888P`._.' jgs/a:f - www.analog.com/blackfin
Have a lot of fun...
BusyBox v1.12.1 (2008-10-29 14:20:54 CST) built-in shell (msh)
Enter 'help' for a list of built-in commands.
root:/> df_dok
~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.2.6 |~~~~~~~~~~~~~~~~~~~~~~~~~~
(c) 2001-2008 The world wide DirectFB Open Source Community
(c) 2000-2004 Convergence (integrated media) GmbH
----------------------------------------------------------------
(*) DirectFB/Core: Single Application Core. (2008-10-29 07:37)
(*) Direct/Thread: Started 'VT Switcher' (303) [CRITICAL OTHER/OTHER 0/0] <12288>...
(*) Direct/Thread: Started 'Keyboard Input' (304) [INPUT OTHER/OTHER 0/0] <12288>...
(*) DirectFB/Input: Keyboard 0.9 (directfb.org)
(*) Direct/Thread: Started 'Linux Input' (305) [INPUT OTHER/OTHER 0/0] <12288>...
(*) DirectFB/Input: Dell Dell USB Keyboard (1) 0.1 (directfb.org)
(*) Direct/Thread: Started 'Linux Input' (306) [INPUT OTHER/OTHER 0/0] <12288>...
(*) DirectFB/Input: HID 04b3:3107 (2) 0.1 (directfb.org)
(*) Direct/Thread: Started 'PS/2 Input' (307) [INPUT OTHER/OTHER 0/0] <12288>...
(*) DirectFB/Input: IMPS/2 Mouse 1.0 (directfb.org)
(*) DirectFB/Graphics: Generic Software Rasterizer 0.6 (directfb.org)
(*) DirectFB/Core/WM: Default 0.3 (directfb.org)
(*) FBDev/Surface: Allocated 320x240 16 bit RGB16 buffer (index 0) at offset 0 and pitch 640.
DirectFB/FBDev: Panning display failed (x=0 y=0 ywrap=0 vbl=1)!
--> Invalid argument
(*) FBDev/Mode: Setting 320x240 RGB16
(*) FBDev/Mode: Switched to 320x240 (virtual 320x240) at 16 bit (RGB16), pitch 640
(*) FBDev/Surface: Allocated 320x240 16 bit RGB16 buffer (index 0) at offset 0 and pitch 640.
DirectFB/FBDev: Panning display failed (x=0 y=0 ywrap=0 vbl=1)!
--> Invalid argument
(*) Direct/Interface: Loaded 'PNG' implementation of 'IDirectFBImageProvider'.
(*) Direct/Interface: Loaded 'FT2' implementation of 'IDirectFBFont'.
(*) Direct/Interface: Loaded 'GIF' implementation of 'IDirectFBImageProvider'.
Benchmarking 256x221 on 320x231 RGB16 (16bit)...
Anti-aliased Text 3.000 secs ( 709.200 KChars/sec) [100.0%]
...
--
Follow-ups
--- Vivi Li 2008-11-12 05:19:22
It fails when a usb mouse has been plugged in; it works without a usbmouse.
--- Graf Yang 2008-11-16 22:26:34
It is a resource conflict, sl811-hcd and bf537-lq035 both need the gpio pin pf4,
you can change sl811-hcd interrupt pin to avoiding.
I have committed a patch that will print some message when the irq pin is
conflicting with others.
--- Graf Yang 2008-11-16 23:18:21
I modified my commit, let request_irq() fail when the requested pin is busy.
--- Vivi Li 2008-11-19 03:11:33
GPIO pin setting has been changed in build script. Appropriate jumper setting
should be done in USB add-on board and BF537-STAMP, refer to build script.
BF537-STAMP: SW5 is all OFF; SW6.4 is OFF;
USB card with ISP1362/SL811: JP3, populate pin 15 & 16; JP5, populate pin
17 & 18.
OK now. Close this bug.
Thanks!
Files
Changes
Commits
Dependencies
Duplicates
Associations
Tags
File Name File Type File Size Posted By
config.kernel.537 application/octet-stream 35687 Vivi Li
config.user.537 application/octet-stream 45402 Vivi Li