[#5164] shell prompt become # on trunk head
Submitted By: Mingquan Pan
Open Date
2009-05-26 05:21:03 Close Date
2009-05-27 02:16:48
Priority:
Medium Assignee:
Mike Frysinger
Status:
Closed Fixed In Release:
N/A
Found In Release:
2010R1 Release:
Category:
N/A Board:
N/A
Processor:
ALL Silicon Revision:
Is this bug repeatable?:
Yes Resolution:
Fixed
Uboot version or rev.:
Toolchain version or rev.:
09r1-rc6
App binary format:
N/A
Summary: shell prompt become # on trunk head
Details:
shell prompt become # on trunk head instead of root:/> after updating over the weekend.
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-2.6.28.10-ADI-2010R1-pre-s
Created: 2009-05-26 8:15:48 UTC
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 4119582 Bytes = 3.9 MB
Load Address: 00001000
Entry Point: 001896dc
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 001896dc
Linux version 2.6.28.10-ADI-2010R1-pre-svn6473 (test@uclinux75-bf533-stamp-wb) (gcc version 4.1.2 (ADI svn)) #189 Tue May 26 16:15:33 CST 2009
Warning: limiting memory to 56MB due to hardware anomaly 05000263
Board Memory: 128MB
Kernel Managed Memory: 128MB
Memory map:
fixedcode = 0x00000400-0x00000490
text = 0x00001000-0x0010be30
rodata = 0x0010be30-0x0015ebb4
bss = 0x0015f000-0x0016f458
data = 0x0016f458-0x0017e000
stack = 0x0017c000-0x0017e000
init = 0x0017e000-0x007cf000
available = 0x007cf000-0x037ff000
DMA Zone = 0x07f00000-0x08000000
Hardware Trace Active and Enabled
Boot Mode: 0
Reset caused by Software reset
Blackfin support (C) 2004-2009 Analog Devices, Inc.
Compiled for ADSP-BF533 Rev 0.3
Blackfin Linux support by http://blackfin.uclinux.org/
Processor Speed: 398 MHz core clock and 79 MHz System Clock
NOMPU: setting up cplb tables
Instruction Cache Enabled for CPU0
Data Cache Enabled for CPU0 (write-back)
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 14223
Kernel command line:
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 256 (order: 8, 1024 bytes)
bfin-rtc: invalid date; resetting
console [ttyBF0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory available: 48776k/131072k RAM, (6468k init code, 1067k kernel code, 457k data, 1024k dma, 73280k reserved)
Calibrating delay loop... 792.57 BogoMIPS (lpj=1585152)
Security Framework initialized
Mount-cache hash table entries: 512
Blackfin Scratchpad data SRAM: 4 KB
Blackfin L1 Data A SRAM: 16 KB (15 KB free)
Blackfin L1 Data B SRAM: 16 KB (16 KB free)
Blackfin L1 Instruction SRAM: 64 KB (53 KB free)
net_namespace: 288 bytes
NET: Registered protocol family 16
Blackfin DMA Controller
stamp_init(): registering device resources
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
msgmni has been set to 95
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler cfq registered
Serial: Blackfin serial driver
bfin-uart.1: ttyBF0 at MMIO 0xffc00400 (irq = 21) is a BFIN-UART
brd: module loaded
smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <nico@cam.org>
eth0: SMC91C11xFD (rev 1) at 20300300 IRQ 40 [nowait]
eth0: Ethernet addr: f2:06:01:61:68:b5
bfin-spi bfin-spi.0: Blackfin on-chip SPI Controller Driver, Version 1.0, regs_base@ffc00500, dma channel@5
rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0
bfin-wdt: initialized: timeout=20 sec (nowayout=0)
TCP cubic registered
NET: Registered protocol family 17
rtc-bfin rtc-bfin: setting system clock to 1970-01-01 10:42:38 UTC (38558)
Freeing unused kernel memory: 6468k freed
dma_alloc_init: dma_page @ 0x007cc000 - 256 pages at 0x07f00000
_____________________________________
a8888b. / Welcome to the uClinux distribution \
d888888b. / _ _ \
8P"YP"Y88 / | | |_| __ __ (TM) |
8|o||o|88 _____/ | | _ ____ _ _ \ \/ / |
8' .88 \ | | | | _ \| | | | \ / |
8`._.' Y8. \ | |__ | | | | | |_| | / \ |
d/ `8b. \ \____||_|_| |_|\____|/_/\_\ |
dP . Y8b. \ For embedded processors including |
d8:' " `::88b \ the Analog Devices Blackfin /
d8" 'Y88b \___________________________________/
:8P ' :888
8a. : _a88P For further information, check out:
._/"Yaa_: .| 88P| - http://blackfin.uclinux.org/
\ YP" `| 8P `. - http://docs.blackfin.uclinux.org/
/ \.___.d| .' - http://www.uclinux.org/
`--..__)8888P`._.' jgs/a:f - http://www.analog.com/blackfin
Have a lot of fun...
BusyBox v1.14.0 (2009-05-26 15:12:17 CST) hush - the humble shell
Enter 'help' for a list of built-in commands.
/ # version
kernel: Linux release 2.6.28.10-ADI-2010R1-pre-svn6473, build #189 Tue May 26 16:15:33 CST 2009
toolchain: bfin-uclinux-gcc release gcc version 4.1.2 (ADI svn)
user-dist: release svn-8133, build #1288 Tue May 26 16:14:29 CST 2009
/ #
************** STEP 3: Start SERIAL TEST
Follow-ups
--- Mike Frysinger 2009-05-26 05:25:53
thought i fixed that, but guess i'll double check
--- Mike Frysinger 2009-05-26 16:43:16
yeah, i cant reproduce this. current trunk installs an /etc/profile which all
login shells source and that sets the PS1 variable.
--- Mike Frysinger 2009-05-26 18:16:29
mmm nm, i had fixed this upstream but didnt put the fix in our local version.
ive done that now.
--- Mingquan Pan 2009-05-27 02:16:48
Yes, it is back to normal. Close.
Files
Changes
Commits
Dependencies
Duplicates
Associations
Tags
File Name File Type File Size Posted By
No Files Were Found