[#5536] sl811 and isp1362 don't work on bf533-ezkit
Submitted By: Vivi Li
Open Date
2009-09-14 23:17:06 Close Date
2009-11-15 22:45:52
Priority:
Medium Assignee:
Michael Hennerich
Status:
Closed Fixed In Release:
N/A
Found In Release:
2009R1-RC6 Release:
Category:
N/A Board:
N/A
Processor:
BF533 Silicon Revision:
Is this bug repeatable?:
Yes Resolution:
Rejected
Uboot version or rev.:
Toolchain version or rev.:
gcc4.1-09r1-rc9
App binary format:
N/A
Summary: sl811 and isp1362 don't work on bf533-ezkit
Details:
sl811 and isp1362 don't work on bf533-ezkit. Config file is attached.
--
U-Boot 2008.10-svn1556 (ADI-2009R1-pre) (Dec 29 2008 - 14:51:27)
CPU: ADSP bf533-0.3 (Detected Rev: 0.3)
Board: ADI BF533 EZ-Kit Lite board
Support: http://blackfin.uclinux.org/
Clock: VCO: 594 MHz, Core: 594 MHz, System: 118.800 MHz
RAM: 32 MB
Flash: 2.1 MB
In: serial
Out: serial
Err: serial
Net: MAC: 00:E0:22:FE:BA:25
Hit any key to stop autoboot: 0
bfin> help loady
loady [ off ] [ baud ]
- load binary file over serial line with offset 'off' and baudrate 'baud'
bfin> loady 0x1000000 115200
## Switch baudrate to 115200 bps and press ENTER ...
## Ready for binary (ymodem) download to 0x01000000 at 115200 bps...
Cackets, 6 retries
## Total Size = 0x0033641c = 3367964 Bytes
## Switch baudrate to 57600 bps and press ESC ...
bfin> bootm 0x1000000
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-2.6.28.10-ADI-2009R1-svn72
Created: 2009-09-14 17:31:05 UTC
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 3367900 Bytes = 3.2 MB
Load Address: 00001000
Entry Point: 001bf6d4
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 001bf6d4
Linux version 2.6.28.10-ADI-2009R1-svn7216 (test@uboot32-533ezkit) (gcc version 4.1.2 (ADI svn)) #19 Mon Sep 14 17:30:56 GMT 2009
bootconsole [early_shadow0] enabled
Warning: limiting memory to 31MB due to hardware anomaly 05000263
Board Memory: 32MB
Kernel Managed Memory: 32MB
Memory map:
fixedcode = 0x00000400-0x00000490
text = 0x00001000-0x001313f0
rodata = 0x001313f0-0x0018f1d8
bss = 0x00190000-0x001a0b48
data = 0x001a0b48-0x001b4000
stack = 0x001b2000-0x001b4000
init = 0x001b4000-0x00674000
available = 0x00674000-0x01eff000
DMA Zone = 0x01f00000-0x02000000
Hardware Trace Active and Enabled
Boot Mode: 0
Blackfin support (C) 2004-2009 Analog Devices, Inc.
Compiled for ADSP-BF533 Rev 0.3
Blackfin Linux support by http://blackfin.uclinux.org/
Processor Speed: 594 MHz core clock and 118 MHz System Clock
NOMPU: setting up cplb tables
Instruction Cache Enabled for CPU0
Data Cache Enabled for CPU0 (write-back)
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 7873
Kernel command line: ip=192.168.0.12:192.168.0.5:192.168.0.1:255.255.255.0::eth0:off
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 128 (order: 7, 512 bytes)
console [ttyBF0] enabled, bootconsole disabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory available: 24844k/32768k RAM, (4864k init code, 1216k kernel code, 524k data, 1024k dma, 296k reserved)
Calibrating delay loop... 1183.74 BogoMIPS (lpj=2367488)
Security Framework initialized
Mount-cache hash table entries: 512
Blackfin Scratchpad data SRAM: 4 KB
Blackfin L1 Data A SRAM: 16 KB (15 KB free)
Blackfin L1 Data B SRAM: 16 KB (16 KB free)
Blackfin L1 Instruction SRAM: 64 KB (53 KB free)
net_namespace: 288 bytes
NET: Registered protocol family 16
Blackfin DMA Controller
ezkit_init(): registering device resources
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
msgmni has been set to 48
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler cfq registered
Serial: Blackfin serial driver
bfin-uart.1: ttyBF0 at MMIO 0xffc00400 (irq = 21) is a BFIN-UART
brd: module loaded
smc91x: not found (-19).
Driver 'sd' needs updating - please use bus_type methods
bfin-spi bfin-spi.0: Blackfin on-chip SPI Controller Driver, Version 1.0, regs_base@ffc00500, dma channel@5
driver isp1362-hcd, 2005-04-04
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0
bfin-wdt: initialized: timeout=20 sec (nowayout=0)
TCP cubic registered
NET: Registered protocol family 17
rtc-bfin rtc-bfin: setting system clock to 1998-07-25 05:25:16 UTC (901344316)
IP-Config: Device `eth0' not found.
Freeing unused kernel memory: 4864k freed
dma_alloc_init: dma_page @ 0x01a33000 - 256 pages at 0x01f00000
_____________________________________
a8888b. / Welcome to the uClinux distribution \
d888888b. / _ _ \
8P"YP"Y88 / | | |_| __ __ (TM) |
8|o||o|88 _____/ | | _ ____ _ _ \ \/ / |
8' .88 \ | | | | _ \| | | | \ / |
8`._.' Y8. \ | |__ | | | | | |_| | / \ |
d/ `8b. \ \____||_|_| |_|\____|/_/\_\ |
dP . Y8b. \ For embedded processors including |
d8:' " `::88b \ the Analog Devices Blackfin /
d8" 'Y88b \___________________________________/
:8P ' :888
8a. : _a88P For further information, check out:
._/"Yaa_: .| 88P| - http://blackfin.uclinux.org/
\ YP" `| 8P `. - http://docs.blackfin.uclinux.org/
/ \.___.d| .' - http://www.uclinux.org/
`--..__)8888P`._.' jgs/a:f - http://www.analog.com/blackfin
Have a lot of fun...
BusyBox v1.13.4 (2009-09-14 15:27:25 GMT) built-in shell (msh)
Enter 'help' for a list of built-in commands.
root:/>
root:/> cat /proc/interrupts
6: 7747 CORE Blackfin CoreTimer
14: 1 INTN rtc-bfin
21: 0 INTN BFIN_UART_RX
22: 4302 INTN BFIN_UART_TX
NMI: 0 CORE Non Maskable Interrupt
Err: 0
root:/>
root:/> ls /dev/
console pts ram4 stdin
cpu_dma_latency ram0 ram5 stdout
fd ram1 ram6 tty
full ram10 ram7 ttyBF0
kmsg ram11 ram8 urandom
log ram12 ram9 usbmon0
mem ram13 random watchdog
network_latency ram14 rtc0 zero
network_throughput ram15 sport0
null ram2 sport1
ptmx ram3 stderr
root:/>
root:/> version
kernel: Linux release 2.6.28.10-ADI-2009R1-svn7216, build #19 Mon Sep 14 17:30:56 GMT 2009
toolchain: bfin-uclinux-gcc release gcc version 4.1.2 (ADI svn)
user-dist: release svn-8738, build #6 Mon Sep 14 17:30:12 GMT 2009
root:/>
--
Follow-ups
--- Michael Hennerich 2009-09-21 06:43:15
Did you add board resources to the BF533-EZKIT platfrom file for the SL811 and
ISP1362?
I guess not - rejected.
-Michael
--- Vivi Li 2009-11-15 22:45:51
Close it.
Files
Changes
Commits
Dependencies
Duplicates
Associations
Tags
File Name File Type File Size Posted By
config.kernel application/octet-stream 31896 Vivi Li