[#6184] can't regonize the usb when our blackfin as host side in usbotg testing on BF527-EZKIIT
Submitted By: angelia wu
Open Date
2010-08-16 04:02:29 Close Date
2010-08-23 00:26:28
Priority:
Medium Assignee:
Bob Liu
Status:
Closed Fixed In Release:
N/A
Found In Release:
2010R1 Release:
Blackfin Linux:2010R1
Category:
N/A Board:
EZKIT Lite
Processor:
BF527 Silicon Revision:
Is this bug repeatable?:
Yes Resolution:
Assigned (Not Start)
Uboot version or rev.:
Toolchain version or rev.:
svn-4681
App binary format:
N/A
Summary: can't regonize the usb when our blackfin as host side in usbotg testing on BF527-EZKIIT
Details:
First:
can't regonize the usb when our blackfin as host side in usbotg testing on BF527-EZKIIT.but the blackfin as device side can work well.
BF527-EZKIT Board version 1.4 work well but version 2.2 has this bug.
And the usbotg testing on BF548-EZKIT work well.
Second:
when i input "mkfs.ext2 /dev/sdb1", some error happened.
root:/> mkfs.ext2 /dev/sdb1
mke2fs 1.41.12 (17-May-2010)
Could not stat /dev/sdb1 --- No such file or directory
The device apparently does not exist; did you specify it correctly?
Third:
the log as follow.
U-Boot 2010.03-svn2335 (ADI-2010R1-pre) (Jun 28 2010 - 10:58:27)
CPU: ADSP bf527-0.0 (Detected Rev: 0.2) (parallel flash boot)
Board: ADI BF527 EZ-Kit board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131.250 MHz
RAM: 64 MB
Flash: 4 MB
In: serial
Out: serial
Err: serial
KGDB: [on serial] ready
Net: bfin_mac
Hit any key to stop autoboot: 0
Using bfin_mac device
TFTP from server 10.100.4.174; our IP address is 10.100.4.50
Filename 'uImage'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#######################################
done
Bytes transferred = 5329007 (51506f hex)
## Booting kernel from Legacy Image at 01000000 ...
Image Name: bf527-2.6.34.4-ADI-2010R1-pre-sv
Created: 2010-08-16 7:11:56 UTC
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 5328943 Bytes = 5.1 MB
Load Address: 00001000
Entry Point: 0020c69c
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 0020c69c
Linux version 2.6.34.4-ADI-2010R1-pre-svn9082 (test@uclinux41) (gcc version 4.3.5 (ADI-trunk/svn-4681) ) #38 Mon Aug 16 15:11:49 CST 2010
register early platform devices
bootconsole [early_shadow0] enabled
bootconsole [early_BFuart1] enabled
early printk enabled on early_BFuart1
Board Memory: 64MB
Kernel Managed Memory: 64MB
Memory map:
fixedcode = 0x00000400-0x00000490
text = 0x00001000-0x0015edc0
rodata = 0x0015edc0-0x001d8ac0
bss = 0x001d9000-0x001ea180
data = 0x001ea180-0x00202000
stack = 0x00200000-0x00202000
init = 0x00202000-0x009ec000
available = 0x009ec000-0x03f00000
DMA Zone = 0x03f00000-0x04000000
Hardware Trace Active and Enabled
Boot Mode: 1
Reset caused by Software reset
Blackfin support (C) 2004-2010 Analog Devices, Inc.
Compiled for ADSP-BF527 Rev 0.2
Blackfin Linux support by http://blackfin.uclinux.org/
Processor Speed: 525 MHz core clock and 131 MHz System Clock
NOMPU: setting up cplb tables
Instruction Cache Enabled for CPU0
External memory: cacheable in instruction cache
Data Cache Enabled for CPU0
External memory: cacheable (write-back) in data cache
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 16002
Kernel command line: root=/dev/mtdblock0 rw clkin_hz=25000000 earlyprintk=serial,uart1,57600 console=tty0 console=ttyBF1,57600 ip=10.100.4.50:10.100.4.174:1f
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory available: 53784k/65536k RAM, (8104k init code, 1399k kernel code, 653k data, 1024k dma, 572k reserved)
Hierarchical RCU implementation.
NR_IRQS:159
Configuring Blackfin Priority Driven Interrupts
console [ttyBF1] enabled, bootconsole disabled
console [ttyBF1] enabled, bootconsole disabled
Calibrating delay loop... 1046.52 BogoMIPS (lpj=2093056)
Security Framework initialized
Mount-cache hash table entries: 512
Blackfin Scratchpad data SRAM: 4 KB
Blackfin L1 Data A SRAM: 16 KB (16 KB free)
Blackfin L1 Data B SRAM: 16 KB (16 KB free)
Blackfin L1 Instruction SRAM: 48 KB (41 KB free)
NET: Registered protocol family 16
Blackfin DMA Controller
ezkit_init(): registering device resources
bio: create slab <bio-0> at 0
SCSI subsystem initialized
bfin-spi bfin-spi.0: Blackfin on-chip SPI Controller Driver, Version 1.0, regs_base@ffc00500, dma channel@7
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-bfin-twi i2c-bfin-twi.0: Blackfin BF5xx on-chip I2C TWI Contoller, regs_base@ffc01400
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
musb_hdrc musb_hdrc.0: USB OTG mode controller at ffc03800 using DMA, IRQ 59
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
msgmni has been set to 105
io scheduler noop registered
io scheduler cfq registered (default)
dma_alloc_init: dma_page @ 0x029c3000 - 256 pages at 0x03f00000
bfin-lq035q1 bfin-lq035q1: 320x240 16-bit RGB FrameBuffer initialized
bfin-otp: initialized
bfin-uart: Blackfin serial driver
bfin-uart.1: ttyBF1 at MMIO 0xffc02000 (irq = 31) is a BFIN-UART
brd: module loaded
m25p80 spi0.1: m25p16 (2048 Kbytes)
Creating 2 MTD partitions on "m25p80":
0x000000000000-0x000000040000 : "bootloader(spi)"
0x000000040000-0x000000200000 : "linux kernel(spi)"
bfin_mii_bus: probed
bfin_mac: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1, mdc_clk=2500000Hz(mdc_div=25)@sclk=131MHz)
bfin_mac bfin_mac.0: Blackfin on-chip Ethernet MAC driver, Version 1.1
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: adp5520-keys as /devices/platform/i2c-bfin-twi.0/i2c-0/0-0032/adp5520-keys.5520/input/input0
ad7879 0-002c: Failed to write AD7879 Touchscreen
ad7879: probe of 0-002c failed with error -1
rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0
bfin-wdt: initialized: timeout=20 sec (nowayout=0)
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
rtc-bfin rtc-bfin: setting system clock to 1970-11-01 23:14:01 UTC (26349241)
IP-Config: Complete:
device=eth0, addr=10.100.4.50, mask=255.255.255.0, gw=10.100.4.174,
host=bf527-ezkit, domain=, nis-domain=(none),
bootserver=10.100.4.174, rootserver=10.100.4.174, rootpath=
Freeing unused kernel memory: 8104k freed
_____________________________________
a8888b. / Welcome to the uClinux distribution \
d888888b. / _ _ \
8P"YP"Y88 / | | |_| __ __ (TM) |
8|o||o|88 _____/ | | _ ____ _ _ \ \/ / |
8' .88 \ | | | | _ \| | | | \ / |
8`._.' Y8. \ | |__ | | | | | |_| | / \ |
d/ `8b. \ \____||_|_| |_|\____|/_/\_\ |
dP . Y8b. \ For embedded processors including |
d8:' " `::88b \ the Analog Devices Blackfin /
d8" 'Y88b \___________________________________/
:8P ' :888
8a. : _a88P For further information, check out:
._/"Yaa_: .| 88P| - http://blackfin.uclinux.org/
\ YP" `| 8P `. - http://docs.blackfin.uclinux.org/
/ \.___.d| .' - http://www.uclinux.org/
`--..__)8888P`._.' jgs/a:f - https://www.analog.com/blackfin
Have a lot of fun...
BusyBox v1.16.2 (2010-08-16 15:09:29 CST) hush - the humble shell
root:/> PHY: 0:01 - Link is Up - 100/Full
root:/> dmesg -c
Linux version 2.6.34.4-ADI-2010R1-pre-svn9082 (test@uclinux41) (gcc version 4.3.5 (ADI-trunk/svn-4681) ) #38 Mon Aug 16 15:11:49 CST 2010
register early platform devices
bootconsole [early_shadow0] enabled
bootconsole [early_BFuart1] enabled
early printk enabled on early_BFuart1
Board Memory: 64MB
Kernel Managed Memory: 64MB
Memory map:
fixedcode = 0x00000400-0x00000490
text = 0x00001000-0x0015edc0
rodata = 0x0015edc0-0x001d8ac0
bss = 0x001d9000-0x001ea180
data = 0x001ea180-0x00202000
stack = 0x00200000-0x00202000
init = 0x00202000-0x009ec000
available = 0x009ec000-0x03f00000
DMA Zone = 0x03f00000-0x04000000
Hardware Trace Active and Enabled
Boot Mode: 1
Reset caused by Software reset
Blackfin support (C) 2004-2010 Analog Devices, Inc.
Compiled for ADSP-BF527 Rev 0.2
Blackfin Linux support by http://blackfin.uclinux.org/
Processor Speed: 525 MHz core clock and 131 MHz System Clock
boot memmap: 00000000009ec000 - 0000000003f00000 (usable)
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 001fd8c4, node_mem_map 009ee000
DMA zone: 126 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 16002 pages, LIFO batch:0
NOMPU: setting up cplb tables
Instruction Cache Enabled for CPU0
External memory: cacheable in instruction cache
Data Cache Enabled for CPU0
External memory: cacheable (write-back) in data cache
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 16002
Kernel command line: root=/dev/mtdblock0 rw clkin_hz=25000000 earlyprintk=serial,uart1,57600 console=tty0 console=ttyBF1,57600 ip=10.100.4.50:10.100.4.174:1f
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Kernel managed physical pages: 16128
Memory available: 53784k/65536k RAM, (8104k init code, 1399k kernel code, 653k data, 1024k dma, 572k reserved)
Hierarchical RCU implementation.
NR_IRQS:159
Configuring Blackfin Priority Driven Interrupts
console [ttyBF1] enabled, bootconsole disabled
Calibrating delay loop... 1046.52 BogoMIPS (lpj=2093056)
Security Framework initialized
Mount-cache hash table entries: 512
Blackfin Scratchpad data SRAM: 4 KB
Blackfin L1 Data A SRAM: 16 KB (16 KB free)
Blackfin L1 Data B SRAM: 16 KB (16 KB free)
Blackfin L1 Instruction SRAM: 48 KB (41 KB free)
NET: Registered protocol family 16
Blackfin DMA Controller
ezkit_init(): registering device resources
bio: create slab <bio-0> at 0
SCSI subsystem initialized
bfin-spi bfin-spi.0: Blackfin on-chip SPI Controller Driver, Version 1.0, regs_base@ffc00500, dma channel@7
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-bfin-twi i2c-bfin-twi.0: Blackfin BF5xx on-chip I2C TWI Contoller, regs_base@ffc01400
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
musb_hdrc: ConfigData=0x00 (UTMI-8)
musb_hdrc: HDRC RTL version 1.900
musb_hdrc musb_hdrc.0: USB OTG mode controller at ffc03800 using DMA, IRQ 59
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Setting up Blackfin MMR debugfs
msgmni has been set to 105
io scheduler noop registered
io scheduler cfq registered (default)
dma_alloc_init: dma_page @ 0x029c3000 - 256 pages at 0x03f00000
bfin-lq035q1 bfin-lq035q1: 320x240 16-bit RGB FrameBuffer initialized
bfin-otp: initialized
bfin-uart: Blackfin serial driver
bfin-uart.1: ttyBF1 at MMIO 0xffc02000 (irq = 31) is a BFIN-UART
brd: module loaded
m25p80 spi0.1: m25p16 (2048 Kbytes)
Creating 2 MTD partitions on "m25p80":
0x000000000000-0x000000040000 : "bootloader(spi)"
0x000000040000-0x000000200000 : "linux kernel(spi)"
bfin_mii_bus: probed
bfin_mac: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1, mdc_clk=2500000Hz(mdc_div=25)@sclk=131MHz)
bfin_mac bfin_mac.0: Blackfin on-chip Ethernet MAC driver, Version 1.1
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: adp5520-keys as /devices/platform/i2c-bfin-twi.0/i2c-0/0-0032/adp5520-keys.5520/input/input0
ad7879 0-002c: Failed to write AD7879 Touchscreen
ad7879: probe of 0-002c failed with error -1
rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0
bfin-wdt: initialized: timeout=20 sec (nowayout=0)
Registered led device: adp5520-led1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
rtc-bfin rtc-bfin: setting system clock to 1970-11-01 23:14:01 UTC (26349241)
IP-Config: Complete:
device=eth0, addr=10.100.4.50, mask=255.255.255.0, gw=10.100.4.174,
host=bf527-ezkit, domain=, nis-domain=(none),
bootserver=10.100.4.174, rootserver=10.100.4.174, rootpath=
Freeing unused kernel memory: 8104k freed
PHY: 0:01 - Link is Up - 100/Full
root:/>
root:/> version
kernel: Linux release 2.6.34.4-ADI-2010R1-pre-svn9082, build #38 Mon Aug 16 15:11:49 CST 2010
toolchain: bfin-uclinux-gcc release gcc version 4.3.5 (ADI-trunk/svn-4681)
user-dist: release svn-9783, build #16 Mon Aug 16 15:11:10 CST 2010
root:/>
root:/> modprobe g_zero autoresume=5
zero gadget: Gadget Zero, version: Cinco de Mayo 2008
zero gadget: zero ready
musb_hdrc musb_hdrc.0: MUSB HDRC host driver
musb_hdrc musb_hdrc.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
root:/> mkfs.ext2 /dev/sdb1
mke2fs 1.41.12 (17-May-2010)
Could not stat /dev/sdb1 --- No such file or directory
The device apparently does not exist; did you specify it correctly?
root:/>
Follow-ups
--- Bob Liu 2010-08-16 05:35:47
I think is the board's(version 2.2) hardware problem. I will test it with a new
one.
-Bob
--- Bob Liu 2010-08-22 23:35:12
fixed, must set sw13 position 2 off and position 3 on.
--- angelia wu 2010-08-23 00:26:28
yes, after i set sw13 position 2 off and position 3 on. the board as host side
can work rightly.
so i closed the bug.
Files
Changes
Commits
Dependencies
Duplicates
Associations
Tags
File Name File Type File Size Posted By
kernel.config.usbotg527 application/octet-stream 47599 angelia wu
user.config.usbotg527 application/octet-stream 48741 angelia wu