[#6203] error on bf533-stamp in ppifcd testing, while on bf537-stamp is well.(2010)

[#6203] error on bf533-stamp in ppifcd testing, while on bf537-stamp is well.

Submitted By: angelia wu

Open Date

2010-08-24 04:05:05 Close Date

2010-08-26 00:49:16

Priority:

Medium Assignee:

Bob Liu

Status:

Closed Fixed In Release:

N/A

Found In Release:

2010R1 Release:

Blackfin Linux:2010R1

Category:

N/A Board:

STAMP

Processor:

BF533 Silicon Revision:

Is this bug repeatable?:

Yes Resolution:

Fixed

Uboot version or rev.:

Toolchain version or rev.:

svn-4681

App binary format:

N/A

Summary: error on bf533-stamp in ppifcd testing, while on bf537-stamp is well.

Details:

error on bf533-stamp in ppifcd testing, while on bf537-stamp is well.

bfin> run ramboot

SMC91111: MAC 00:e0:22:fe:06:1d

Using SMC91111-0 device

TFTP from server 10.100.4.174; our IP address is 10.100.4.50

Filename 'uImage'.

Load address: 0x1000000

Loading: #################################################################

#################################################################

###############

done

Bytes transferred = 4027449 (3d7439 hex)

## Booting kernel from Legacy Image at 01000000 ...

Image Name: bf533-2.6.34.5-ADI-2010R1-pre-sv

Created: 2010-08-24 6:04:00 UTC

Image Type: Blackfin Linux Kernel Image (gzip compressed)

Data Size: 4027385 Bytes = 3.8 MiB

Load Address: 00001000

Entry Point: 0019ff90

Verifying Checksum ... OK

Uncompressing Kernel Image ... OK

Starting Kernel at = 0019ff90

console [ttyBF0] enabled, bootconsole disabled

Calibrating delay loop... 989.18 BogoMIPS (lpj=1978368)

Security Framework initialized

Mount-cache hash table entries: 512

Blackfin Scratchpad data SRAM: 4 KB

Blackfin L1 Data A SRAM: 16 KB (16 KB free)

Blackfin L1 Data B SRAM: 16 KB (16 KB free)

Blackfin L1 Instruction SRAM: 64 KB (51 KB free)

NET: Registered protocol family 16

Blackfin DMA Controller

stamp_init(): registering device resources

bio: create slab <bio-0> at 0

bfin-spi bfin-spi.0: Blackfin on-chip SPI Controller Driver, Version 1.0, regs_base@ffc00500, dma channel@5

Switching to clocksource bfin_cs_cycles

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

UDP hash table entries: 256 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

NET: Registered protocol family 1

msgmni has been set to 95

io scheduler noop registered

io scheduler cfq registered (default)

bfin-uart: Blackfin serial driver

bfin-uart.0: ttyBF0 at MMIO 0xffc00400 (irq = 21) is a BFIN-UART

brd: module loaded

smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <nico@fluxnic.net>

eth0: SMC91C11xFD (rev 1) at 20300300 IRQ 40 [nowait]

eth0: Ethernet addr: 00:e0:22:fe:06:1d

rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0

i2c /dev entries driver

i2c-gpio i2c-gpio.0: using pins 2 (SDA) and 3 (SCL)

bfin-wdt: initialized: timeout=20 sec (nowayout=0)

TCP cubic registered

NET: Registered protocol family 17

rtc-bfin rtc-bfin: setting system clock to 1970-01-14 17:28:01 UTC (1186081)

eth0: link down

IP-Config: Gateway not on directly connected network.

dma_alloc_init: dma_page @ 0x0279c000 - 256 pages at 0x07f00000

Freeing unused kernel memory: 6100k freed

eth0: link up, 100Mbps, full-duplex, lpa 0x41E1

_____________________________________

a8888b. / Welcome to the uClinux distribution \

d888888b. / _ _ \

8P"YP"Y88 / | | |_| __ __ (TM) |

8|o||o|88 _____/ | | _ ____ _ _ \ \/ / |

8' .88 \ | | | | _ \| | | | \ / |

8`._.' Y8. \ | |__ | | | | | |_| | / \ |

d/ `8b. \ \____||_|_| |_|\____|/_/\_\ |

dP . Y8b. \ For embedded processors including |

d8:' " `::88b \ the Analog Devices Blackfin /

d8" 'Y88b \___________________________________/

:8P ' :888

8a. : _a88P For further information, check out:

._/"Yaa_: .| 88P| - http://blackfin.uclinux.org/

\ YP" `| 8P `. - http://docs.blackfin.uclinux.org/

/ \.___.d| .' - http://www.uclinux.org/

`--..__)8888P`._.' jgs/a:f - https://www.analog.com/blackfin

Have a lot of fun...

BusyBox v1.16.2 (2010-08-24 12:00:17 CST) hush - the humble shell

root:/> ifconfig

eth0 Link encap:Ethernet HWaddr 00:E0:22:FE:06:1D

inet addr:10.100.4.50 Bcast:10.100.4.255 Mask:255.255.255.0

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:3 errors:0 dropped:0 overruns:0 frame:0

TX packets:1 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000

RX bytes:587 (587.0 B) TX bytes:42 (42.0 B)

Interrupt:40 Base address:0x300 DMA chan:ff

lo Link encap:Local Loopback

inet addr:127.0.0.1 Mask:255.0.0.0

UP LOOPBACK RUNNING MTU:16436 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

root:/> cd /bin/

root:/bin> ./ppifcd_test -b 533

gpio/direction: No such file or directory

gpio/value: No such file or directory

i2c_write_register: error: could not write msg: No such device or address

i2c_read_register: error: could not write msg: No such device or address

************* Calculated Times Based on the actual Camera setting *************

Master Clock = 48 MHz

et0t0l0f aIe tSmt a t0upsx l=c o0kxrorko

time = 0 usec

*******************************************************************************

Read Start: 1186814.713198

Read End: 1186814.757350

Total Frame Capture Time: 44150 usec

root:/bin> ./ppifcd_test -b 533 -c3 -t

ERROR:Trigger option unsupported on BF533-STAMP

gpio/direction: No such file or directory

gpio/value: No such file or directory

i2c_write_register: error: could not write msg: No such device or address

i2c_read_register: error: could not write msg: No such device or address

P*P*I* *E*r*r oarc:l tPdPTIm sSBtsadtou sh =c u0lxC1m0r0 0e t

g *************

Master Clock = 48 MHz

row_time = 224 pixel clocks

total_frame_time = 0 pixel clocks

total_frame_time = 0 uPeP

***I* *E***r*r*o***r*:* ***P*P*I*** *S*t***a*t*u***s* *=*** *0*x***1*0*0***0*

Read Start: 1186844.409135

Read End: 1186844.432562

Total Frame Capture Time: 23425 usec

Read StartPPI Error: PPI Statuse = 0xd1 0001 6

4.469553

Total Frame Capture Time: 36796 usec

Read Start: 1186844.469739

Read End: 1186844.494483

Total Frame Capture Time: 24742 usec

root:/bin> ppifcd_test -b 533 -c3 /var/img.bmp

gpio/direction: No such file or directory

gpio/value: No such file or directory

i2c_write_register: error: could not write msg: No such device or address

i2c_read_register: error: could not write msg: No such device or address

************* Calculated Times Based on the actual Camera sePtPI Er*ror: PP*I Statuss = 0x1000

48 MHz

row_time = 224 pixel clocks

total_frame_time = 0 pixel clocks

total_frame_time = 0 usec

*****************************************************P*P*I* *E*r*r*o*r*:* *P*P*I

Status = 0x1000

Read Start: 1186931.725164

Read End: 1186931.754254

Total Frame Capture Time: 29088 usec

Read Start: 1186931.754447

Read End: 1186931.78P9P1I

To aE rramr oartur: iPe: P4I4 usSct

tus = 0x1000

Read Start: 1186931.789172

Read End: 1186931.824838

Total Frame Capture Time: 35664 usec

*******************************************************************************

Saved: /var/img.bmp

Size : 1311798

*******************************************************************************

root:/bin> time ppifcd_test -b 533 -c100

i2c_write_register: error: could not write msg: No such device or address

i2c_read_register: error: could not write msg: No such device or address

uMss e= l0cx 1 0culated080M z Based on thP PcIu lECrmrro re:t nP P*I* *S*t*a*t

row_time = 224 pixel clocks

total_frame_time = 0 pixel clocks

total_frame_time = 0 usec

***********************************P*PI Er*ror: PP*I Status = 0x1000

********

Read Start: 1186978.709164

Read End: 1186978.739845

Total Frame Capture Time: 30678 usec

Read Start: 1186978.740039

0x1000 oare:C pPuPeIT mS:t2a8t3uuse 78.7P7P7I

Read Start: 1186978.768056

Read End: 1186978.804619

Total Frame Capture Time: 36560 usec