[#6550] print prompt error after running fixed_code case on bf548 ezkit(2011)

[#6550] print prompt error after running fixed_code case on bf548 ezkit

Submitted By: Mingquan Pan

Open Date

2011-04-19 03:54:58 Close Date

2011-05-05 23:22:06

Priority:

Medium Assignee:

steven miao

Status:

Closed Fixed In Release:

N/A

Found In Release:

2011R1 Release:

Category:

N/A Board:

N/A

Processor:

ALL Silicon Revision:

Is this bug repeatable?:

Yes Resolution:

Fixed

Uboot version or rev.:

Toolchain version or rev.:

5013

App binary format:

N/A

Summary: print prompt error after running fixed_code case on bf548 ezkit

Details:

print prompt error after running fixed_code case on bf548 ezkit.and failed to show key input words.

TFTP from server 10.100.4.174; our IP address is 10.100.4.50

Filename 'uImage.fixed_code'.

Load address: 0x2000000

Loading: #################################################################

#################################################################

########################################

done

Bytes transferred = 5354327 (51b357 hex)

bfin> bootm

## Booting kernel from Legacy Image at 02000000 ...

Image Name: bf548-0.2-2.6.38.3-ADI-2011R1-pr

Created: 2011-04-16 23:03:55 UTC

Image Type: Blackfin Linux Kernel Image (gzip compressed)

Data Size: 5354263 Bytes = 5.1 MiB

Load Address: 00001000

Entry Point: 0028ddf4

Verifying Checksum ... OK

Uncompressing Kernel Image ... OK

Starting Kernel at = 0028ddf4

Linux version 2.6.38.3-ADI-2011R1-pre-svn9857 (test@uclinux61-bf548-std) (gcc version 4.3.5 (ADI-trunk/svn-5013) ) #322 Sun Apr 17 07:03:48 CST 2011

bootconsole [early_shadow0] enabled

bootconsole [early_BFuart1] enabled

early printk enabled on early_BFuart1

Board Memory: 64MB

Kernel Managed Memory: 64MB

Memory map:

fixedcode = 0x00000400-0x00000490

text = 0x00001000-0x001b9188

rodata = 0x001b9188-0x0025256c

bss = 0x00253000-0x00265a44

data = 0x00265a44-0x00284000

stack = 0x00282000-0x00284000

init = 0x00284000-0x009d7000

available = 0x009d7000-0x03e00000

DMA Zone = 0x03e00000-0x04000000

Hardware Trace Active and Enabled

Boot Mode: 1

Reset caused by Software reset

Compiled for ADSP-BF548 Rev 0.2

Blackfin Linux support by http://blackfin.uclinux.org/

Processor Speed: 525 MHz core clock and 131 MHz System Clock

NOMPU: setting up cplb tables

Instruction Cache Enabled for CPU0

External memory: cacheable in instruction cache

L2 SRAM : uncacheable in instruction cache

Data Cache Enabled for CPU0

External memory: cacheable (write-through) in data cache

L2 SRAM : uncacheable in data cache

Built 1 zonelists in Zone order, mobility grouping off. Total pages: 15748

Kernel command line: root=/dev/mtdblock2 rw rootfstype=jffs2 earlyprintk=serial,uart1,57600 console=ttyBF1,57600

PID hash table entries: 256 (order: -2, 1024 bytes)

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory available: 52804k/65536k RAM, (7500k init code, 1760k kernel code, 812k data, 2048k dma, 612k reserved)

NR_IRQS:295

Configuring Blackfin Priority Driven Interrupts

console [ttyBF1] enabled, bootconsole disabled

Calibrating delay loop... 1046.52 BogoMIPS (lpj=2093056)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512

Blackfin Scratchpad data SRAM: 4 KB

Blackfin L1 Data A SRAM: 16 KB (16 KB free)

Blackfin L1 Data B SRAM: 16 KB (16 KB free)

Blackfin L1 Instruction SRAM: 48 KB (41 KB free)

Blackfin L2 SRAM: 128 KB (128 KB free)

NET: Registered protocol family 16

Blackfin DMA Controller

ezkit_init(): registering device resources

bio: create slab <bio-0> at 0

SCSI subsystem initialized

spi spi0.2: Warning: SPI CPHA not set: Slave Select not under software control!

See Documentation/blackfin/bfin-spi-notes.txt

bfin-spi bfin-spi.0: Blackfin on-chip SPI Controller Driver, Version 1.0, regs_base@ffc00500, dma channel@4

bfin-spi bfin-spi.1: Blackfin on-chip SPI Controller Driver, Version 1.0, regs_base@ffc02300, dma channel@5

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

i2c-bfin-twi i2c-bfin-twi.0: Blackfin BF5xx on-chip I2C TWI Contoller, regs_base@ffc00700

i2c-bfin-twi i2c-bfin-twi.1: Blackfin BF5xx on-chip I2C TWI Contoller, regs_base@ffc02200

Advanced Linux Sound Architecture Driver Version 1.0.23.

musb-hdrc: version 6.0, musb-dma, host, debug=0

musb-hdrc musb-hdrc: MUSB HDRC host driver

musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

musb-hdrc musb-hdrc: USB Host mode controller at ffc03c00 using DMA, IRQ 82

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

UDP hash table entries: 256 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

NET: Registered protocol family 1

debug-mmrs: setting up Blackfin MMR debugfs

msgmni has been set to 103

io scheduler noop registered (default)

bf54x-lq043: FrameBuffer initializing...

dma_alloc_init: dma_page @ 0x029cb000 - 512 pages at 0x03e00000

bfin-uart: Blackfin serial driver

bfin-uart.1: ttyBF1 at MMIO 0xffc02000 (irq = 48) is a BFIN-UART

bfin-otp: initialized

brd: module loaded

scsi0 : pata-bf54x

ata1: PATA max UDMA/66 irq 68

physmap platform flash device: 02000000 at 20000000

physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000089 Chip ID 0x00881e

Intel/Sharp Extended Query Table at 0x010A

Using buffer write method

Using auto-unlock on power-up/resume

cfi_cmdset_0001: Erase suspend on write enabled

RedBoot partition parsing not available

Using physmap partition information

Creating 3 MTD partitions on "physmap-flash.0":

0x000000000000-0x000000080000 : "bootloader(nor)"

0x000000080000-0x000000480000 : "linux kernel(nor)"

0x000000480000-0x000001000000 : "file system(nor)"

m25p80 spi0.1: m25p16 (2048 Kbytes)

Creating 2 MTD partitions on "m25p80":

0x000000000000-0x000000080000 : "bootloader(spi)"

0x000000080000-0x000000200000 : "linux kernel(spi)"

bf5xx-nand bf5xx-nand.0: data_width=8, wr_dly=3, rd_dly=3

NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit)

Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":

0x000000000000-0x000000080000 : "bootloader(nand)"

0x000000080000-0x000000480000 : "linux kernel(nand)"

0x000000480000-0x000010000000 : "file system(nand)"

smsc911x: Driver version 2008-10-21.

smsc911x-mdio: probed

eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)

net eth0: MAC Address: 00:e0:22:fe:bf:4e

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

input: bf54x-keys as /devices/platform/bf54x-keys/input/input0

rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0

i2c /dev entries driver

bfin-wdt: initialized: timeout=20 sec (nowayout=0)

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

ALSA device list:

No soundcards found.

TCP cubic registered

NET: Registered protocol family 17

rtc-bfin rtc-bfin: setting system clock to 2004-05-31 04:12:59 UTC (1085976779)

mmc0: host does not support reading read-only switch. assuming write-enable.

mmc0: new SD card at address e624

ata1.00: ATA-6: TOSHIBA MK4032GAX, AD101A, max UDMA/100

ata1.00: 78140160 sectors, multi 16: LBA48

ata1.00: configured for UDMA/66

blk_queue_max_segments: set to minimum 1

scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK4032GA AD10 PQ: 0 ANSI: 5

sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.2 GiB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

sda: sda1 sda2

sd 0:0:0:0: [sda] Attached SCSI disk

Freeing unused kernel memory: 7500k freed

_____________________________________

a8888b. / Welcome to the uClinux distribution \

d888888b. / _ _ \

8P"YP"Y88 / | | |_| __ __ (TM) |

8|o||o|88 _____/ | | _ ____ _ _ \ \/ / |

8' .88 \ | | | | _ \| | | | \ / |

8`._.' Y8. \ | |__ | | | | | |_| | / \ |

d/ `8b. \ \____||_|_| |_|\____|/_/\_\ |

dP . Y8b. \ For embedded processors including |

d8:' " `::88b \ the Analog Devices Blackfin /

d8" 'Y88b \___________________________________/

:8P ' :888

8a. : _a88P For further information, check out:

._/"Yaa_: .| 88P| - http://blackfin.uclinux.org/

\ YP" `| 8P `. - http://docs.blackfin.uclinux.org/

/ \.___.d| .' - http://www.uclinux.org/

`--..__)8888P`._.' jgs/a:f - http://www.analog.com/blackfin

Have a lot of fun...

BusyBox v1.18.4 (2011-04-17 06:48:37 CST) hush - the humble shell

root:/>

root:/> cd bin/

root:/bin> usb 1-1: new high speed USB device using musb-hdrc and address 2

scsi1 : usb-storage 1-1:1.0

base64 fixed_code_p klogd mv sync

bcdm fsck ln netstat syslogd

boa fsck.ext2 losetup nice sz

busybox fsck.ext3 lrz pidof tar

cat fsck.msdos ls ping telnet

chgrp fsck.vfat lsmod play telnetd

chmod ftp lsz pngview thdm

chown ftpd mdev portmap tone

cp gdbserver mixer ps touch

cpio getopt mkdir pwd traps_test

date getty mkdosfs rcp true

dd grep mke2fs reboot umount

df gunzip mkfs.ext2 rev uname

dhcpcd gzip mkfs.ext3 rm usleep

dhrystone hostname mkfs.jffs2 rmdir vconfig

dmesg hush mkfs.msdos rmmod version

dnsdomainname hwclock mkfs.vfat route vi

dosfsck ifconfig mknod rsh video_test

e2fsck inetd modinfo rshd vplay

echo init modprobe rz vrec

event_test insmod more sed watch

false iostat mount sh watchdogd

fdisk jpegview mpstat sleep whetstone

fixed_code kill mtdm stty zcat

root:/bin> scsi 1:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 6.51 PQ: 0 ANSI: 0 CCS

sd 1:0:0:0: [sdb] 2014271 512-byte logical blocks: (1.03 GB/983 MiB)

sd 1:0:0:0: [sdb] Write Protect is off

sd 1:0:0:0: [sdb] Asking for cache data failed

sd 1:0:0:0: [sdb] Assuming drive cache: write through

sd 1:0:0:0: [sdb] Asking for cache data failed

sd 1:0:0:0: [sdb] Assuming drive cache: write through

sdb: sdb1 sdb2

sd 1:0:0:0: [sdb] Asking for cache data failed

sd 1:0:0:0: [sdb] Assuming drive cache: write through

sd 1:0:0:0: [sdb] Attached SCSI removable disk

root:/bin> ./fixed_code

PASS: test_xchg32

PASS: test_cas32

PASS: test_add32

PASS: test_inc32

PASS: test_sub32

PASS: test_dec32

PASS: test_ior32

PASS: test_and32

PASS: test_xor32

:/bin> :/bin> :/bin> :/bin> :/bin> :/bin> :/bin> :/bin> :/bin> :/bin> :/bin> :/bin> :/bin> sd 0:0:0:0: [sda] Synchronizing SCSI cache

musb-hdrc musb-hdrc: remove, state 1

usb usb1: USB disconnect, address 1

usb 1-1: USB disconnect, address 2

musb-hdrc musb-hdrc: USB bus 1 deregistered

Restarting system.�

U-Boot 2010.06-svn2467 (ADI-2010R1) (Oct 08 2010 - 16:04:41)

CPU: ADSP bf548-0.0 (Detected Rev: 0.2) (parallel flash boot)

Board: ADI BF548 EZ-Kit board

Support: http://blackfin.uclinux.org/

Clock: VCO: 525 MHz, Core: 525 MHz, System: 131.250 MHz

RAM: 64 MiB

Flash: 16 MiB

NAND: 256 MiB

MMC: Blackfin SDH: 0

In: serial

Out: serial

Err: serial

KGDB: [on serial] ready

Net: smc911x-0

Hit any key to stop autoboot: 0

bfin>

Follow-ups

--- steven miao 2011-05-03 05:11:09

it was because fixed_code test close stdout, and not do cleanup before test

exit.

--- Mingquan Pan 2011-05-05 23:22:06

Yes, it is ok now. Close.

Files

Changes

Commits

Dependencies

Duplicates

Associations

Partner Forums

Partner Libraries

[#6550] print prompt error after running fixed_code case on bf548 ezkit(2011)