[#6615] flash erase on bf526-ezkit fails(2011)

[#6615] flash erase on bf526-ezkit fails

Submitted By: Mingquan Pan

Open Date

2011-05-27 04:36:47 Close Date

2011-06-02 01:20:33

Priority:

Medium Assignee:

steven miao

Status:

Closed Fixed In Release:

N/A

Found In Release:

2011R1 Release:

Category:

N/A Board:

N/A

Processor:

ALL Silicon Revision:

Is this bug repeatable?:

Yes Resolution:

Fixed

Uboot version or rev.:

Toolchain version or rev.:

5013

App binary format:

N/A

Summary: flash erase on bf526-ezkit fails

Details:

flash erase on bf526-ezkit fails.

## Booting kernel from Legacy Image at 02000000 ...

Image Name: bf526-0.0-2.6.39-rc7-ADI-2011R1-

Created: 2011-05-18 20:16:27 UTC

Image Type: Blackfin Linux Kernel Image (gzip compressed)

Data Size: 4058006 Bytes = 3.9 MiB

Load Address: 00001000

Entry Point: 00216c64

Verifying Checksum ... OK

Uncompressing Kernel Image ... OK

Starting Kernel at = 00216c64

Linux version 2.6.39-rc7-ADI-2011R1-pre-svn9892 (test@uclinux81-bf526) (gcc version 4.3.5 (ADI-trunk/svn-5013) ) #588 Thu May 19 04:16:18 CST 2011

bootconsole [early_shadow0] enabled

bootconsole [early_BFuart1] enabled

early printk enabled on early_BFuart1

Board Memory: 64MB

Kernel Managed Memory: 64MB

Memory map:

fixedcode = 0x00000400-0x00000490

text = 0x00001000-0x0016aed8

rodata = 0x0016aed8-0x001e4ba0

bss = 0x001e5000-0x001f6bcc

data = 0x001f6bcc-0x0020e000

stack = 0x0020c000-0x0020e000

init = 0x0020e000-0x00773000

available = 0x00773000-0x03f00000

DMA Zone = 0x03f00000-0x04000000

Hardware Trace active and enabled

Boot Mode: 1

Compiled for ADSP-BF526 Rev 0.0

Blackfin Linux support by http://blackfin.uclinux.org/

Processor Speed: 400 MHz core clock and 80 MHz System Clock

NOMPU: setting up cplb tables

Instruction Cache Enabled for CPU0

External memory: cacheable in instruction cache

Data Cache Enabled for CPU0

External memory: cacheable (write-back) in data cache

Built 1 zonelists in Zone order, mobility grouping off. Total pages: 16002

Kernel command line: root=/dev/mtdblock0 rw ip=10.100.4.50 earlyprintk=serial,uart1,57600 console=ttyBF1,57600 ip=10.100.4.50:10.100.4.174:10.100.4.174:255.255.255.0:bf526-ezbrd:eth0:off

PID hash table entries: 256 (order: -2, 1024 bytes)

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory available: 56276k/65536k RAM, (5524k init code, 1447k kernel code, 653k data, 1024k dma, 612k reserved)

NR_IRQS:159

Configuring Blackfin Priority Driven Interrupts

console [ttyBF1] enabled, bootconsole disabled

Calibrating delay loop... 792.57 BogoMIPS (lpj=1585152)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512

Blackfin Scratchpad data SRAM: 4 KB

Blackfin L1 Data A SRAM: 16 KB (16 KB free)

Blackfin L1 Data B SRAM: 16 KB (16 KB free)

Blackfin L1 Instruction SRAM: 48 KB (41 KB free)

NET: Registered protocol family 16

Blackfin DMA Controller

ezbrd_init(): registering device resources

bio: create slab <bio-0> at 0

SCSI subsystem initialized

bfin-spi bfin-spi.0: Blackfin on-chip SPI Controller Driver, Version 1.0, regs_base@ffc00500, dma channel@7

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

i2c-bfin-twi i2c-bfin-twi.0: Blackfin BF5xx on-chip I2C TWI Contoller, regs_base@ffc01400

musb-hdrc: version 6.0, musb-dma, host, debug=0

musb-hdrc musb-hdrc: MUSB HDRC host driver

musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

musb-hdrc musb-hdrc: USB Host mode controller at ffc03800 using DMA, IRQ 59

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

UDP hash table entries: 256 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

NET: Registered protocol family 1

debug-mmrs: setting up Blackfin MMR debugfs

JFFS2 version 2.2. (NAND) Â 2001-2006 Red Hat, Inc.

msgmni has been set to 109

io scheduler noop registered (default)

bfin-uart: Blackfin serial driver

bfin-uart.1: ttyBF1 at MMIO 0xffc02000 (irq = 31) is a BFIN-UART

bfin-otp: initialized

brd: module loaded

physmap platform flash device: 00400000 at 20000000

physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000020 Chip ID 0x008815

Intel/Sharp Extended Query Table at 0x0039

cfi_cmdset_0001: Erase suspend on write enabled

cmdlinepart partition parsing not available

RedBoot partition parsing not available

Using physmap partition information

Creating 3 MTD partitions on "physmap-flash.0":

0x000000000000-0x000000040000 : "bootloader(nor)"

0x000000040000-0x000000200000 : "linux kernel(nor)"

0x000000200000-0x000000400000 : "file system(nor)"

m25p80 spi0.1: sst25wf040 (512 Kbytes)

Creating 2 MTD partitions on "m25p80":

0x000000000000-0x000000040000 : "bootloader(spi)"

0x000000040000-0x000000080000 : "linux kernel(spi)"

bfin_mii_bus: probed

bfin_mac: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1, mdc_clk=2500000Hz(mdc_div=15)@sclk=80MHz)

bfin_mac bfin_mac.0: eth0: Blackfin on-chip Ethernet MAC driver, Version 1.1

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0

bfin-wdt: initialized: timeout=20 sec (nowayout=0)

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

TCP cubic registered

NET: Registered protocol family 17

rtc-bfin rtc-bfin: setting system clock to 2004-05-31 02:57:01 UTC (1085972221)

dma_alloc_init: dma_page @ 0x0275c000 - 256 pages at 0x03f00000

IP-Config: Complete:

device=eth0, addr=10.100.4.50, mask=255.255.255.0, gw=10.100.4.174,

host=bf526-ezbrd, domain=, nis-domain=(none),

bootserver=10.100.4.174, rootserver=10.100.4.174, rootpath=

Freeing unused kernel memory: 5524k freed

_____________________________________

a8888b. / Welcome to the uClinux distribution \

d888888b. / _ _ \

8P"YP"Y88 / | | |_| __ __ (TM) |

8|o||o|88 _____/ | | _ ____ _ _ \ \/ / |

8' .88 \ | | | | _ \| | | | \ / |

8`._.' Y8. \ | |__ | | | | | |_| | / \ |

d/ `8b. \ \____||_|_| |_|\____|/_/\_\ |

dP . Y8b. \ For embedded processors including |

d8:' " `::88b \ the Analog Devices Blackfin /

d8" 'Y88b \___________________________________/

:8P ' :888

8a. : _a88P For further information, check out:

._/"Yaa_: .| 88P| - http://blackfin.uclinux.org/

\ YP" `| 8P `. - http://docs.blackfin.uclinux.org/

/ \.___.d| .' - http://www.ucPinux.org/

`--..__)8888P`._.' jgs/a:f - http://www.analog.com/blackfin

Have a lot of fun...

HY: 0:01 - Link is Up - 100/Full

BusyBox v1.18.4 (2011-05-18 23:37:48 CST) hush - the humble shell

root:/> version

kernel: Linux release 2.6.39-rc7-ADI-2011R1-pre-svn9892, build #588 Thu May 19 04:16:18 CST 2011

toolchain: bfin-uclinux-gcc release gcc version 4.3.5 (ADI-trunk/svn-5013)

user-dist: release svn-10167, build #7173 Thu May 19 04:15:15 CST 2011

root:/> successful boot attempt

************** STEP 3: MTD test

cat /proc/mtd

dev: size erasesize name

mtd0: 00040000 00010000 "bootloader(nor)"

mtd1: 001c0000 00010000 "linux kernel(nor)"

mtd2: 00200000 00010000 "file system(nor)"

mtd3: 00040000 00001000 "bootloader(spi)"

mtd4: 00040000 00001000 "linux kernel(spi)"

root:/>

Case 1 ...PASS

************** STEP 4: Erase MTD

flash_unlock /dev/mtd2

root:/> flash_erase -j /dev/mtd2 0 0

Erasing 64 Kibyte @ 0 -- 0 % complete flash_erase: Cleanmarker written at 0

Erasing 64 Kibyte @ 10000 -- 3 % complete flash_erase: Cleanmarker written at 10000

Erasing 64 Kibyte @ 20000 -- 6 % complete flash_erase: Cleanmarker written at 20000

Erasing 64 Kibyte @ 30000 -- 9 % complete flash_erase: Cleanmarker written at 30000

Erasing 64 Kibyte @ 40000 -- 12 % complete flash_erase: Cleanmarker written at 40000

Erasing 64 Kibyte @ 50000 -- 15 % complete flash_erase: Cleanmarker written at 50000

Erasing 64 Kibyte @ 60000 -- 18 % complete flash_erase: Cleanmarker written at 60000

Erasing 64 Kibyte @ 70000 -- 21 % complete flash_erase: Cleanmarker written at 70000

Erasing 64 Kibyte @ 80000 -- 25 % complete flash_erase: Cleanmarker written at 80000

Erasing 64 Kibyte @ 90000 -- 28 % complete flash_erase: Cleanmarker written at 90000

Erasing 64 Kibyte @ a0000 -- 31 % complete flash_erase: Cleanmarker written at a0000

Erasing 64 Kibyte @ b0000 -- 34 % complete flash_erase: Cleanmarker written at b0000

Erasing 64 Kibyte @ c0000 -- 37 % complete flash_erase: Cleanmarker written at c0000

Erasing 64 Kibyte @ d0000 -- 40 % complete flash_erase: Cleanmarker written at d0000

Erasing 64 Kibyte @ e0000 -- 43 % complete flash_erase: Cleanmarker written at e0000

Erasing 64 Kibyte @ f0000 -- 46 % complete flash_erase: Cleanmarker written at f0000

Erasing 64 Kibyte @ 100000 -- 50 % complete flash_erase: Cleanmarker written at 100000

Erasing 64 Kibyte @ 110000 -- 53 % complete flash_erase: Cleanmarker written at 110000

Erasing 64 Kibyte @ 120000 -- 56 % complete flash_erase: Cleanmarker written at 120000

Erasing 64 Kibyte @ 130000 -- 59 % complete flash_erase: Cleanmarker written at 130000

Erasing 64 Kibyte @ 140000 -- 62 % complete flash_erase: Cleanmarker written at 140000

Erasing 64 Kibyte @ 150000 -- 65 % complete flash_erase: Cleanmarker written at 150000

Erasing 64 Kibyte @ 160000 -- 68 % complete flash_erase: Cleanmarker written at 160000

Erasing 64 Kibyte @ 170000 -- 71 % complete flash_erase: Cleanmarker written at 170000

Erasing 64 Kibyte @ 180000 -- 75 % complete flash_erase: Cleanmarker written at 180000

Erasing 64 Kibyte @ 190000 -- 78 % complete flash_erase: Cleanmarker written at 190000

Erasing 64 Kibyte @ 1a0000 -- 81 % complete flash_erase: Cleanmarker written at 1a0000

Erasing 64 Kibyte @ 1b0000 -- 84 % complete flash_erase: Cleanmarker written at 1b0000

Erasing 64 Kibyte @ 1c0000 -- 87 % complete flash_erase: Cleanmarker written at 1c0000

Erasing 64 Kibyte @ 1d0000 -- 90 % complete flash_erase: Cleanmarker written at 1d0000

Erasing 64 Kibyte @ 1e0000 -- 93 % complete flash_erase: Cleanmarker written at 1e0000

Erasing 64 Kibyte @ 1f0000 -- 96 % complete libmtd: error!: MEMERASE64 ioctl failed for eraseblock 31 (mtd2)

error 30 (Read-only file system)

flash_erase: error!: /dev/mtd2: MTD Erase failure

error 30 (Read-only file system)

Erasing 64 Kibyte @ 200000 -- 100 % complete

root:/>

Last passed time: 2010_Sep_28_13_58, ucdist ver: 9833, kernel ver: 9171

Case 2 ...FAIL

Follow-ups

--- Mike Frysinger 2011-05-28 17:14:34

probably the same as bug #4884

--- Mingquan Pan 2011-05-29 22:40:32

This should be a different one, since when #4884 is filed, this bug isn't

occouring and this case is good.

--- Mike Frysinger 2011-05-29 22:46:19

i imagine that's merely by accident

--- steven miao 2011-05-30 04:04:24

it's mtd-utils's issue, flash_unlock miss unlocking the last erase block of mtd

partion.

--- Mingquan Pan 2011-06-02 01:24:50

Yes, it can flash erase to the end now.

Close.

Files

Changes

Commits

Dependencies

Duplicates

Associations