Thread Details

  • State Verified Answer
  • Replies 5 replies
  • Subscribers 34 subscribers
  • Views 1344 views
  • Users 0 members are here
Options 

        

            Post
             Go back to editing
        

    

    


    

    









		


















	
	
			
	
			
		
	
	
		

	    
	    
	    		
Flashing Evaluation BF537-EZKit Lite with uboot & kernel image

		
	
				

			

									
					    tejaswi
					
							

            
            			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Feb 16, 2018 
				
			
			
		
    
		
		                     
				
        		
    
		    
		    		    
		    			
    
			    
    Hi,
    
 
    I am new to the forum and currently there are several questions running in my mind. 
    
 
    I am able to successfully get the BF537-EZkit up with the help of Visual DSP5.0 and run the example codes on the same. I have run the example flash programing on the kit and able to boot up the kit without running the Visual DSP5.0.
    
 
    Now, I have few question or doubts, request you to kindly address the same.
    
 
      Followed the steps in https://blackfin.uclinux.org/doku.php?id=bootloaders:u-boot:compiling  for compiling the uboot for BF537. 
    
 
    1. What is the difference between make bf537-stamp, bf537-mintaur, bf537-pnav and bf537-srv1.
    
 
    2. Which command should be used to build uboot for evaluation kit and for the bare bf537 processor. 
    
 
    Regards,
    
 
    Tejaswi
    
			
    
			
									
		                             
                        

    
    
                                            
                 Audio Signal Processors
                
                                                    
                 bf537-stamp
                
                                                    
                 Blackfin Embedded Processors
                
                                
            
    
    
    
		
    

				
				        
        		
    
			
						
									
												
			
			
                        
                                    
                        
                        
                        
            
			            
						
						
			
			
			
			
		
    

        
        
        
    
					
    
			
    


    
















    
	
    
	
    
					



			








	
	
	
	



Parents
	
      
	

    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
		    
		    		    
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
						
                            
            
            				
            
                on Feb 28, 2018 5:30 AM
            
            
						
			            		
      
		
										0
					
	
      

		
		
      
		
      
                                
                                                            
      
					
      Hi Tejaswi,
      
 
      For UART boot, after switching to position 7, and reset, you are not supposed to see meaningful output on the console, instead, you are suppose to download u-boot from this UART port, as described by the document. After the downloading through UART is done, u-boot will get run and you start to get output on console.
      
 
      Thanks
      
 
      Aaron  
      
			
      

		
			
	      

		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
				
						
				
				
		
		
      
			
		
      
	
      

      

      • 

	
    



Reply

      


    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
		    
		    		    
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
						
                            
            
            				
            
                on Feb 28, 2018 5:30 AM
            
            
						
			            		
      
		
										0
					
	
      

		
		
      
		
      
                                
                                                            
      
					
      Hi Tejaswi,
      
 
      For UART boot, after switching to position 7, and reset, you are not supposed to see meaningful output on the console, instead, you are suppose to download u-boot from this UART port, as described by the document. After the downloading through UART is done, u-boot will get run and you start to get output on console.
      
 
      Thanks
      
 
      Aaron  
      
			
      

		
			
	      

		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
				
						
				
				
		
		
      
			
		
      
	
      

      

      • 


    


Children
	
    No Data