I get the following error message when I link-compile-download. "System.componentmodel.win32exception (0x80004005): The system cannot find the file specified at system.diagnostics.process.startwithcreaterprocess(processstartinfostartinfo) at system.di

Could not find the folders mentioned in the error message on my pc. 

Parents
  • Dave,

    Attached is a dspproj file.

    I have these same issues with any of my current dsp project files.

    I am running: win10 64 bit, SigmaStudio 4.1, HP Zbook workstation. Ethernet connection to HW (Simon-Kaloi rPod) audio playback and show control unit. Also a serial connection to unit's console port which lets me monitor and give some cpu commands.

    Unit has four AD1953 codecs of which I am using 3

    What I am encountering is:

    1, error message noted previously when I "link-compile-download" followed by "file could not be read" message

    2, stepping through the three error messages (apparently one per codec) yields following serial output on console port:

    Halt request, verifing completion...
     100:0x04 0x00
    Halt request, verifing completion...
     100:0x04 0x00
    Halt request, verifing completion...
     100:0x04 0x00
    Halt request, verifing completion...
    3, Still bar at bottom of screen shows green as if a good connection, says 100%, and "active downloaded"
    4, In SigmaStudio Screen controls affect the output but not as desired. for example IC1  input 1 (ch 0), output 1 and 2 make a mono channel (left) with a single input, four band parametric EQ and 3500Hz 12dB/oct crossover
       4a, enabling/disabling Gen filter2 affects gen filter3, likewise Gen filter3 affects Gen filter2. I can hear the change in frequency response as I switch.
       4b, moving control on parametric disables output filters
       4c, disabling/enabling input highpass filter also disables output filters.
    5, IC2 (right channel) IC2 input2 (ch 1) outputs3 and 4 behaves similarly
    6, IC3 (sums left and right channels for woofer output) uses input 3 outputs 5 and 6 and behaves similarly
    7, Audio will not play through any output until a control is moved
    8, I have returned the unit to the manufacturer and they say it works correctly on their SigmaStudio installation
    9, this why I suspect the installation on my pc
    10, Although, I Installed SS with disabled antivirus and firewall as Administrator and run it as administrator..
    testv4.dspproj.zip
Reply
  • Dave,

    Attached is a dspproj file.

    I have these same issues with any of my current dsp project files.

    I am running: win10 64 bit, SigmaStudio 4.1, HP Zbook workstation. Ethernet connection to HW (Simon-Kaloi rPod) audio playback and show control unit. Also a serial connection to unit's console port which lets me monitor and give some cpu commands.

    Unit has four AD1953 codecs of which I am using 3

    What I am encountering is:

    1, error message noted previously when I "link-compile-download" followed by "file could not be read" message

    2, stepping through the three error messages (apparently one per codec) yields following serial output on console port:

    Halt request, verifing completion...
     100:0x04 0x00
    Halt request, verifing completion...
     100:0x04 0x00
    Halt request, verifing completion...
     100:0x04 0x00
    Halt request, verifing completion...
    3, Still bar at bottom of screen shows green as if a good connection, says 100%, and "active downloaded"
    4, In SigmaStudio Screen controls affect the output but not as desired. for example IC1  input 1 (ch 0), output 1 and 2 make a mono channel (left) with a single input, four band parametric EQ and 3500Hz 12dB/oct crossover
       4a, enabling/disabling Gen filter2 affects gen filter3, likewise Gen filter3 affects Gen filter2. I can hear the change in frequency response as I switch.
       4b, moving control on parametric disables output filters
       4c, disabling/enabling input highpass filter also disables output filters.
    5, IC2 (right channel) IC2 input2 (ch 1) outputs3 and 4 behaves similarly
    6, IC3 (sums left and right channels for woofer output) uses input 3 outputs 5 and 6 and behaves similarly
    7, Audio will not play through any output until a control is moved
    8, I have returned the unit to the manufacturer and they say it works correctly on their SigmaStudio installation
    9, this why I suspect the installation on my pc
    10, Although, I Installed SS with disabled antivirus and firewall as Administrator and run it as administrator..
    testv4.dspproj.zip
Children
No Data